Search Documents

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

By H. R. Barnhurst

IT would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Doubtless the crossing of the sticks of wood in building a, wood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets utilized metal bars as supports for the same purpose. It is probable that Tubal Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in east iron, grate bars cane in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a. natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deficiencies in its primary development, and within that tine there has been great advancement in the means of producing initially fire of high efficiency, so that to clay we are moving rapidly toward loth high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to Min nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for raking what was at best a, very imperfect pulverization of the coal, and the expense of preparation was very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 10, 1913

By J. P. Dunlop

THE fact is-notable though probably little known that the United States is the only nation obtaining and distributing through its Government bureaus any data pertaining to waste metals and drosses. Some foreign governments do issue reports relating to mine or smelter production of primary metals, but none gives in scope and detail the information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for the year 1907 obtained and compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-metal industry. The National Conservation Commission had emphasized its opinion that the known domestic supply of certain kinds of the more important metals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there. been a lamentable lack of any data regarding the quantity of scrap metals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses were nearly as essential to both producers and consumers as the statistics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey to do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins-issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

Jan 1, 1928

By H. Q. Golder

INTRODUCTION The stabilization of slopes is not a design problem. A slope is designed before it is made. For a slope to be stabilized it must already exist. The basic problem has existed for a long time. It started with cuts in soil and rock made in the 18th century during the construction of the canals which were developed at that time, and continued into the 19th century with the development of the railways, and in the 20th century with motor roads and lately open pit mining. It is not difficult to stabilize a slope, but certain questions must be asked and answered. These are: i) How much stability is required? ii) For how long is it required? iii) How important is the cost? These three questions indicate the basic problem of Civil Engineering, which is that the solution to any problem is a compromise between safety, cost and time. Stabilization of slopes is no exception. If the slope exists why is stabilization a problem? There are many possible reasons, for instance, a neighbouring and similar slope may have failed, or it may be necessary to change the conditions of the slope, steepen it, increase its height, put weight at the top, or construct a building at the foot in which case added security is required, or guarantee its stability for a longer time. MECHANISM OF FAILURE In order to pick the correct method of stabilization the mechanism of failure must be understood and the immediate cause of failure known. Often to remove the cause is the best remedy. The mechanism of failure has been studied over a period of many years in landslide problems. Pit slope failures are very similar to some types of landslides. (1) (2) (3) (4) In one sense there are many causes of landslides. Terzaghi lists 19. This means that there cannot be a standard solution to a stabilization problem. In another sense, it can be said that there is only one cause, which is gravity. This is a constant, never failing force which cannot be

Jan 1, 1971

By B. M. Bird

ONE of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practise for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical danc-ing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1928

By L. E. Porter, H. P. Hassel

The state of California produced 310,-996,696 bbl. of oil and about 415,832,000 M cu. ft. of gas in 1944. Such oil production represented 18.5 per cent of the nation's production, as compared with 19 per cent in 1943 ,The tremendous demand placed upon the California fields is indicated by the monthly production in 1944, as follows: Month Barrels per Day Jan................... 809,262 Feb.................. 820,712 Mar.................. 824,592 .4pr ................. 829,973 May.................. 832,068 June.................. 846,038 July.................. 849,231 Aug.................. 858,932 Sept.................. 885,823 Oct................... 877,667 Nov.................. 876,613 Dec.................. 883,847 In all, 2100 wells in proved areas and 269 wildcats were drilled in California during the year 1944. At the end of the year, approximately 270 wells were drilling in the state, as compared with 156 wells at the same time in the preceding year. Nine new fields or new zone discoveries were made during the year, which, according to best estimates, will contribute some 77,000,000 bbl. of new reserves; in addition, the extensions of old fields will increase the new reserves about 165,000,000 bbl., or a combined total, through dis- coveries of new fields, zones, and extensions, of 242,000,000 bbl., offsetting to the extent of about 78 per cent the total oil produced during the year. Geographically, the reserves from these new field and zone discoveries and extensions are distributed as follows: Per Cent San Joaquin Valley........ 72 Coast Area............... 24 Los Angeles Basin Fields. . . 4 100 The state's reserves of crude oil at the end of the year have been estimated to be distributed as follows: The outstanding development project for the year was that of the United States Navy in the Naval Petroleum Reserve No. I, Elk Hills field. During the year, 115 wells were completed in this field, and at the close of the year an average of 19 strings of tools were drilling. This program is being jointly conducted by the Standard Oil Co. of California with the Navy and is designed to increase the production of Naval Petroleum Reserves from approxi-

Jan 1, 1945

By H. E. Rorschach

Activity in Oklahoma oil fields made 1937 one of the best years since 1926. During the year, 3454 wells were completed, an increase of about 25 per cent over the year 1936. Purchasers reports filed with the Corporation Commission of the State of Oklahoma showed a total of 221,842,-788 bbl. of oil purchased from leases in 1937, an increase of about 10 per cent over 1936. The assembly of a complete table of all of the oil fields in Oklahoma has not yet been achieved. Many of the early records of operators and pipe-line companies are incomplete. Table 1 includes all of the new fields, and this year there has been added work done covering pools discovered in previous years, so that most of the important fields in the state of Oklahoma are included therein. The outstanding development of the year was the discovery of the producing horizon classified as the Wilcox in western Payne County by the Mid-Continent Petroleum Corporation on a unitized block in sec. 18, Tp. 18 N., R. 2 E. This block is operated hy the Mid-Continent and owned in conjunction with the Carter Oil Co., Transwestern Oil Co. and Sinclair-Prairie Oil Co. Another important development of the year was the extension of the deep zone in the old Fox-Milroy area of Carter and Stephens Counties. Some of the other discoveries made during the year 1937 are South Cromwell, discovered by Sinclair-Prairie Oil Co.; Cromwell extension of the Fitts pool in Pontotoc County; discovery of the Langston area in Logan County; discovery of the Sporn area in Lincoln County by Skelly Oil Co. and the discovery of the North Wellston area in Lincoln County by Standard Oil & Gas Co. Table 2 shows the new oil areas discovered in Oklahoma during the year 1937 and areas that were discovered in 1936 but developed in 1937. Fox-Milroy Area.—Three wells were completed to the deep producing zone during the year. One of the wells completed in the early part of the year uas the Carter Oil Company's No. 1 Harley in sec. 24, Tp. 2 S., R. 4 W., 3 1/2 miles northwest of the original discovery well, the Ruth

Jan 1, 1938

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing' with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

By E. C. Potter

It is not the purpose of this paper to enter into the minutiae of a subject so vast, upon which volumes have already been written and volumes more might still be written, but simply to pass in review the characteristic features of that practice, which, dating from the blowing-in of the Edgar Thomson "A" furnace in 1879 and continuing down to the present day, has given to American blast-furnace operations a new significance. The blowing-in of " A" furnace marked the beginning of a new era in the science of iron-smelting if, indeed, it was not the very birth of science as applied to this industry in the United States. American blast-furnace practice in its generic sense and world-wide significance dates from that day, and really all that is valuable, all that is remarkable or worthy of discussion, is embraced in the experiences and achievements of the past fifteen years. Back of that we find only the dead level of mediocrity, or worse, a dispoition to " let well enough alone;" a general, almost universal, employment of " rule of thumb " methods. The application of scientific principles and methods was rare and, indeed, previous to the introduction of the Bessemer process in the early seventies, science had no place in controlling the operations of the American blast-furnace. The old practice consisted mainly in dumping raw materials in at the top of the furnace and tapping out iron and slag at the bottom, for the successful consummation of which the furnace-manager directed his best energies toward keeping the furnace as free as possible from "gobbing" with, alas ! but indifferent success. The burdening of the furnace was based largely on Mark Twain's receipt for " Johnny-cake," altered to suit the circumstances, viz.: a lot of ore, a lot of fuel and about a quarter of a lot of flux. The possible capacities of furnace-plants were not nearly realized. Enormous wastes were permitted, unheeded because not understood. In the use of fuel quantum suff. was always the rule. Increase of product was not thought of because it was not deemed wise or safe to attempt

Jan 1, 1894

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the lengt of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel-per-day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel-per-day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable-yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from she commonly understood barrel-per-day value, in that the conditions turrounding the sale of one lease or property at a fair market value may

Jan 1, 1923

By Dart Wantland, C. A. Heiland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By F. E. Bash

PREVIOUS to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to deter mine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than T 1 X 10-5 per ° C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25° C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table 1. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best coefficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese,-13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 per cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 9, 1919

By E. H. Hamilton

WHEN starting a series of experiments on the use of powdered coal in lead blast furnaces to replace coke, I realized that in copper smelting the problem is simpler because the sulfur recovers the copper in the form of matte. In lead smelting there are greater difficulties because a reducing atmosphere must be maintained in the active, zone corresponding to each tuyere in order to get the best recovery of lead. Therefore, the feed of powdered coal must be quite regular, uniform and under control. The molten products issuing from the taphole are the resultant of the work of all the tuyeres and it can readily be con-ceived that one part of the furnace may be forming slag with a higher lead content than the slag formed in other parts of the furnace. At first, we used only one tuyere situated on the back of the furnace. This was for the purpose of getting all of our regulations under the regular operating conditions. We tried every known system of feed and found they were not dependable and our present system was finally worked out, and so far as we know, is the only working system that will give uniformly good saving in lead blast furnaces. We placed a Bristol self-recording thermometer on the feed floor. This gives a 24-hr. continuous record of the temperature of the gases leaving the furnace. We put a self-recording gage on the "15-lb." air used in the injector. A second recording Bristol gage was put on the low-pressure air (40 oz.). I realized that it was necessary that we should know the exact weight of coal going into each tuyere and that it should 'be under observation at all times. L. W. Kirk was assigned to the problem and developed the open sight feed and the distributor, so that we now have the coal being fed into each tuyere in sight of the men in charge. We have an apothecary's balance beside the furnace, and the operator takes the pan and inserts it under the stream of falling powdered coal for one minute, and places the pan on the scale, the other scale pan having weights indicating the desired amount to be fed to each tuyere per minute.

Jan 10, 1922

By S. Fisher Morris

THE New River coal-field embraces that portion of the Appalachian coal formation which lies on the waters of the New River, principally in Fayette and Raleigh counties, West Virginia, covering a strip of territory about forty miles in length along the line of the Chesapeake and Ohio Railroad from Quinnimont to Kanawha Falls, where the New River empties into the Kanawha, the railroad following the banks of the river the whole distance. (See map.) Between Kanawha Falls and the Valley of the Ohio lies the great Kanawha region, and these two coal-fields possess a greater variety of coal than can be found in any other portion of the country, enabling them to furnish the best fuels for any of the various demands of manufacture or domestic use, the Kanawha region possessing many varieties of gas, hard splint, and cannel coal, and the New River region bituminous and semi-bituminous, steam and coking coal. The New River, in its westward course towards the Kanawha, has cut its way entirely through the Seral conglomerate or No. XII of the Pennsylvania Reports, the Umbral red shales of No. XI appearing at the foot of the mountains at the eastern end of the region at Quinnimont, one of the upper ledges of the Conglomerate forming the summits; while at the western end, at Kanawha Falls, the top of the Conglomerate is nearly down to the level of the river, a portion of the " Lower Productive Measures" forming the greater portion of the mountains. These mountains rise abruptly from the banks of the river to a height of from 800 to 1200 feet, leaving only here and there narrow strips of bottom land, a few acres in extent; and as the measures consist principally of hard sandstones, shales, and conglomerates lying in a nearly horizontal position, the mountain-sides are very precipitous, with many long and high cliffs, which, with the great height of the mountains, give the country a very rugged appearance. Along the sides of these mountains fronting on the New River and its many tributaries there are exposed the outcroppings of several veins of bituminous and, semi-bituminous coal, varying in thickness from a few inches to over four feet, five of them being workable, or

Jan 1, 1880

By Raymond J. Kujawa

For general purposes, insulating materials may be any of those mineral substances that provide a barrier between a desired human environmental feature and an unwanted condition. In this sense, radiation shields, electrical insulations, cryogenic insulation, and acoustical barriers would qualify. For this chapter only the thermal and acoustic insulations used for the median range of normal comfort control will be covered. Because of their magnitude and complexity the other fields are left to other chapters. In another sense, this section deals only with the ultra-lightweight aggregates and insulations, rather than the multitude of light-weight structural materials. Definitions and Uses The insulating materials covered in this chapter are the three groups of mineral products that provide thermal or acoustic barriers through the median temperatures encountered in home and industry. The three mineral categories are perlite, vermiculite, and the silicate wools whether they be categorized as glass, mineral, or rock. Perlites are those amorphous aluminum silicates with minor impurities that take the form of a felsitic, glassy lava possessing a pearl-like luster and concentric cracking. In a more commercial sense the term is used to describe either the natural or processed acidic, volcanic glass, containing from 2 to 5% combined water, that may be converted to a frothy mass by heating rapidly to the softening point. Vermiculites are micaceous, hydrated magnesium iron aluminum sheet silicates of varying composition. Commercial vermiculites are any of these sheet silicates that are capable of sufficient expansion on rapid heating to make an acceptable, highly porous product. Mineral wools, rock wools, silicate cottons, glass fiber are generic names for manufactured fibers in which the fiber forming substance may be slag, certain rocks, or glass. The fibers may be made by a blowing or spinning process. The resultant fibers may be felted or matted or gathered in the manner best suited to the use. The three groups may be used competitively to insulate ceilings and walls. The fibers have strong advantages in this area as they may be manufactured in batts that are stable in residential wall construction. The perlites and vermiculites are more suited to insulate cores and cavities of masonry walls and as plaster and concrete aggregates for thermal insulations. Vermiculite is widely used for insulating attic floors. Because of manufacturing techniques and controls, the glass fibers have made great strides as composites in the plastics industry but only a few of these uses classify in the insulation category.

Jan 1, 1975

By C. A. Heiland, Dart Wantland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By S. E. Bretherton

Most metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other rnetals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver metals are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthlees. Such was the experience of the oldest mines in Leadville,.Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered by smelting the cinder or clinker left in the re-

Jan 1, 1915