Search Documents

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By D. Turnbull, R. E. Cech

FISHER, Hollomon, and Turnbull have developed a theory for the nucleation of martensite. They first tested the theory on Fe-C alloys and low alloy steels. The major factor influencing nucleation of martensite was considered to be statistical composition fluctuations occurring in small regions at high temperature and frozen-in on quenching. These local regions of varying size and composition serve as nucleation centers. They become supercritical, one by one, as temperature is progressively lowered, resulting in temperature-dependent or athermal transformation. Fisher next applied nucleation theory to substi-tutional solid solution alloys. Detailed predictions were made for Fe-Ni alloys because of the availability of free energy data on this system. It was shown that composition fluctuations that were significant energy-wise did not occur, and nucleation frequencies could be calculated from average properties of the system. Nucleation was predicted to occur as time-dependent and having the functional relationship to give a C curve of nucleation frequency vs temperature. The analysis further predicted that the nucleation frequency was extremely sensitive to composition. Experimentally, it would be found that the transformation in some compositions is so slow that measurable amounts will not form in a reasonable length of time. With other compositions, only slightly different, the nucleation frequency becomes so great that the material becomes transformed while still distant in temperature from the maximum nucleation frequency. On quenching an alloy of such composition, the observed transformation kinetics would be similar to those found in Fe-C alloys. Cech and Hollomon repeated experiments of Kurdjumov n which the kinetics of transformation were similar to those predicted by Fisher for Fe-Ni alloys. The alloy studied in this investigation contained 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn. Fisher,' using an idealized model for the extent of transformation as a function of the number of martensite crystals per grain of parent phase, derived nucleation frequencies from the transformation curves of Cech and Hollomon. Complicating influences such as coupling effects between grains in the polycrystalline specimens were neglected. Nevertheless, excellent agreement was found between the theoretically and experimentally derived nucleation frequencies. These experiments, however, could not provide a critical test of the theory. Experimental nucleation frequencies could vary widely from those calculated, depending upon the extent of deviation from ideal partitioning and the extent of coupling effects. Further, since the compositions of material theoretically analyzed and experimentally determined were different, the free energy changes involved in the experimental work could only be estimated. Also, the effect of heterogeneities on the transformation kinetics was not considered. For these reasons, it was decided that experiments designed to test the validity of the Fisher analysis must be conducted on binary Fe-Ni alloys, which were the ones considered theoretically by Fisher. The martensite transformation in Fe-Ni alloys has been the subject of considerable study. Machlin and Cohen have shown that transformation proceeds in a manner quite unlike that in any other ferrous alloy system. They found that single crystals would transform to a large extent in a single burst. In large grain polycrystalline specimens, frequently more than one grain and sometimes the whole specimen would transform at the same instant in this manner. Results on filings indicated that different particles would undergo the burst transformation at widely different temperatures. These results support the conclusion that the transformation behavior could not be described by a single nucleation frequency as would be the case if the nucleation were homogeneous. It appeared that further work was necessary to define the factors responsible for burst-type transformation, so that the conditions could be altered to favor homogeneous nucleation of martensite if such could be accomplished. This report summarizes the results of some experiments conducted with powdered Fe-Ni alloys for this purpose and the re-

Jan 1, 1957

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,' `Associations,' or `Societies,' composed of those engaged in these occupations, and by the periodical publication of `essays' or `papers' communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

By William Fink

SINCE so many different curves have been published for the solid solubility of zinc in aluminum, it seems desirable to definitely establish the correct curve by two or more independent methods. The curve published in part I1 was based entirely upon X-ray measurements because the other methods employed at that time were not satisfactory. The present paper (the seventeenth of this series on high-purity aluminum alloys) describes the determination of the solid solubility of zinc in aluminum by the measurement of electrical resistivity at temperature and by microscopic examination. Since the publication of our part I in 1932, an investigation of the solubility relations in the aluminum-zinc system has been reported by Schmid and Wassermann2, who obtained their solubility results from lattice-parameter measurements on heat-treated and quenched speci-mens. The diagram that they published is shown in Fig. 1. In this investigation they also found by X-ray measurements that the parameter of the gamma phase changed continuously with zinc content and at such a rate that it would be identical with that of the beta phase at 60 atomic per cent zinc. It was concluded therefore that the beta and gamma phases, from the point of view of structural relationship, are one single phase. They also suggested a gap of immiscibility between 270° and 350° C. The complete boundary in this region could not be deter-mined satisfactorily by the method employed and therefore was not shown in their diagram.

Jan 1, 1936

By N. A. D. Parlee

The diffusion rate of hydrogen in liquid iron has been measured by a gas-liquid metal diffusion cell technique. The diffusion cell was formed by immersing an alumina tube containing hydrogen gas at 1 atm in a bath of stagnant liquid iron. The change in the composition of the melt in the cell was determined by measuring the rate of absorption of the gas in the cell. The appropriate solution to Fick's second law was used to examine the data and calculate diffusivi-ties. The absorption of hydrogen in stagnant pure liquid iron has been found to be diffusion-controlled. The results show that the chemical diffusion coefficient, D, of hydrogen in pure iron in the range of 1547" to 1726°C can be represented by the following Arrhenius relation: D(sq cnz per sec) = 3.2 x X exp(- 3300 i 1800/RT) where the uncertainty in the activation energy corresponds to the YO pct confidence level. Oxygen in the melt (above 0.015 pct 2) increased the apparent rate of absorption of hydrogen. The importance of diffusion data on liquid metals for predicting the rates of certain metallurgical processes has been recognized for a long time. Moreover, these data are much needed to test and develop theory for diffusion in liquid metals. Despite this practical and theoretical interest, however, relatively little reliable information about diffusion in liquid metals is available in the literature. This is particularly true for gas components such as hydrogen, oxygen, and nitrogen in liquid metals, where almost no data on chemical diffusion coefficients are to be found. This is probably due to a multitude of experimental difficulties particularly associated with high-temperature melts. In an effort to fill this gap in information, a research program was undertaken to study the diffusivities and rates of solution of gases in liquid metals. This paper presents the results of a study of the diffusion of hydrogen in liquid iron. EXPERIMENTAL METHOD Two methods for the study of the kinetics of dissolution of gases in liquid metals are being employed in this laboratory. Both involve the measurement of the volume of gas absorbed by the melt as a function of time and as such both avoid the uncertainties involved in chemical analyses of quenched samples for relatively small amounts of gas. In the first method, the gas dissolves in an inductively stirred melt and, in the absence of a slow surface reaction, the results are often interpreted in terms of mass transport across a liquid "boundary layer" between the homogeneous gas phase and well-stirred part of the melt. Other interpretations of the results of such experiments have also been described in the literature.1'5 In the second method a gas-liquid metal diffusion cell is used.' The gas dissolves in a cylindrical column of stagnant liquid metal and, in the absence of a slow surface reaction, the results are interpreted in terms of a non-steady-state diffusion solution to Fick's second law. The weakness of the first method is that while it gives information on the mechanism of absorption by stirred melts it yields an overall rate constant which even in the simplest cases depends on the nature and the thickness of the "mass transport layer" or "boundary layer". It yields no values of diffusion coefficients. The second method was used in this research because in many cases it is possible to determine the diffusion coefficient of the gas component in the liquid metal. In this research it has been utilized to measure diffusion coefficients of hydrogen in liquid iron. The apparatus used was essentially the same as that described by Mizikar, Grace, and par lee but certain modifications have been introduced to meet the elevated temperatures and special conditions of this research. Fig. 1 is a schematic drawing of the apparatus and Table I gives the identification of various parts in this figure. The diffusion cell, shown in detail in Fig. 2, was formed by immersing an impervious alumina tube (hereafter called absorption tube) in a bath of pure liquid iron contained in an alumina crucible. Two types of tubes were used, Morganite triangle RR and McDanel AP35. The crucible was contained in a vertical impervious alumina combustion tube (32 mm ID by 914 mm long) which was closed at both ends by water-cooled brass heads employing O-ring compression seals, Fig. 1. A protection tube enclosing a Pt, 5 pct Rh-Pt, 20 pct Rh thermocouple was introduced through the lower end of the combustion tube

Jan 1, 1968

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By C. M. Loeb, A. M. Gaudin, J. H. Brown

THE object of most size reduction operations in the mineral industry is to liberate the grains of valuable minerals in the ore from those of the gangue. This is usually accomplished by crushing and grinding the entire mass of ore until there is only a small probability that any single particle contains more than one mineral. During this size reduction only limited control exists over size or composition of the particles exposed to the breaking action, and there is no control over the paths followed by cracks generated during the operation. This lack of control usually results in overgrinding and in production of large quantities of very fine material. The first detriment, overgrinding, is costly in itself, but when combined with the second factor it is doubly so. Not only is the fracture of a free particle unnecessary—the fracture of these particles may also make subsequent separation operations difficult, inefficient, and wasteful. It has been pointed out&apos; that if the object of size reduction is to liberate the valuable mineral component of the ore then, ideally, fracture should follow intergranular paths to the exclusion of trans-granular ones. This would result in liberation of the valuable minerals with as little size reduction as possible. This ideal comminution operation is referred to as intergranular comminution, and it was the object of the investigation to determine the extent to which it could be developed by heat treatments. There are many indications in the literature that heating rocks prior to crushing may be favorable. Reports by Holman,2 Yates3 and Myers&apos; are pertinent. These investigators showed that heating certain rocks prior to crushing them did, in fact, improve their crushing characteristics in that fewer fines were produced, although the fact that intergranular comminution was being effected apparently was overlooked. In addition, Sosman noted that if there is appreciable anisotropism in the thermal coefficients of expansion of even a pure mineral, then considerable permanent separation of the grains of the rock can be expected as a result of heating the rock to a high temperature.&apos; By the same token, if there are ap- preciable differences in the thermal expansion coefficients of the various minerals of a multi-component rock, similar results should be obtained by heating this rock. This has been tested, partially, by Brenner," who obtained patents covering the heat treatment of some pegmatitic rocks in order to facilitate comminution of these materials. It has also been demonstrated that this may occur in taconite." Also, the possibility of causing decomposition of one mineral in a rock as a means of promoting intergranular fracture has been considered. Seigle2 and Schiffman et al. have obtained patents on such processes as applied to calcareous iron ores. These reports all indicate that heat treatments prior to crushing may contribute materially to intergranular comminution, but they also indicate that no organized attempt has been made to determine the controlling factors of the method or to determine its applicability in general. The present article is a report on the initial phase of such an investigation. The authors have reviewed the claims of prior investigators and have attempted, also, to establish the factors that might determine the applicability of heat treatments in the mineral industry. In this work 2000-g samples of various rocks were heated in a small laboratory furnace and crushing and sizing operations were carried out in standard laboratory equipment. All samples of each rock were as nearly identical as possible in particle size, grain size, and composition and contained only lumps coarse enough to contain many grains each. Tests on Granite A number of tests were made on a coarse grained Finnish granite obtained in the form of coarse chips from a local monument yard. This rock exhibited little variation from piece to piece in either composition or grain size. The minerals contained were quartz, orthoclase, small amounts of hornblende, and minute quantities of mica. Grain size ranged from about 1 mm to about 3 mm. Temperature of the Heat Treatment: In some cases the granite was heated to a particular temperature and crushed, hot, immediately upon withdrawal from the furnace—in others the rock was allowed to cool before crushing, but without quenching to room temperature after heating. In most tests on granite the heating period was about 2 hr with the furnace at the highest temperature for about 1 hr. Cases in which these periods were varied greatly will be presented separately.

Jan 1, 1959

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By Eckley B. Coxe

Having been appointed, on February 19th, 1890, a member of the Commission created by the Legislature of Pennsylvania for the purpose of investigating the " Waste of Coal Mining, with the View to the Utilizing of the Waste" (waste in this case referring specially to the small sizes of anthracite heretofore thrown away), my attention was naturally directed to the mash economical method of burning these small sizes.* Although I had been Familiar with the burning of anthracite for • many years, I found when I came to study the matter carefully that I was far from thoroughly understanding it, particularly with reference to the hurning of the smaller sizes, and that the literature of the subject, which was not very extensive, had more of a tendency to confuse than to enlighten me. I began therefore to investigate the subject so as to arrive if possible at some definite principles applicable to the question. With the aid of my assistant, Mr. John R. Wagner, I began at Drifton a series of experiments upon the burning of small anthracites. We first erected a small furnace with a grate 3 feet long and 2 feet wide, with which we experimented about two months. From the information thus acquired, we designed and built another furnace of about the same size, which gave us facilities for extending our investigations still further. After experimenting several months with the second furnace, we built a third one, which was much larger, having a grate area of about 68 square feet, which was exactly the size of the grate used in the boiler-plants of&apos; Coxe Bros. &

Jan 1, 1894

By R. L. Templin

THE increasing use of aluminum and its alloys in commercial fields has demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure aluminum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. COMPARISON OF CUTTING TOOLS Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30° to 50°, making the total angle of the cutting edge of the tool from 35° to 55°. A side

Jan 1, 1928

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.&apos; Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By G. M. Schwartz, J. N. Gundersen

Utilization of magnetite-bearing taconite from the great Mesabi range of Minnesota is fast becoming a major industry in the state. The planning and early development stages of taconite processing projects have been de-scribed1-3 and an excellent discussion has appeared recently4 concerning the current mining, crushing, concentrating, and pelletizing techniques of the Reserve Mining Co., whose operations lie entirely within the Eastern Mesabi district. The present paper will deal only with some of the geological aspects of taconite utilization in the district, with emphasis placed upon some of the common mineralogical and textural features of the tacon-ites currently being mined or stripped and how these factors generally affect the potential recovery of the iron from the metamorphosed Biwabik iron-formation. The generalized geologic setting of the Eastern Mesabi district is presented in Fig. 1. The small circles on the geologic map, adapted from Grout and Broderick,3 mark the location of drill holes that were available for inspection during this study through the courtesy of Reserve Mining and Erie Mining Cos. The cores from these holes were divided into stratigraphic units and examined for their mineral content. Typical mineral associations and grain fabrics were also determined from hundreds of thin and polished sections. Available metallurgical tests made it possible to determine the probable response of a given variety of taconite to magnetic concentration. The longitudinal section of Fig. 1, projected along the strike of the iron formation, presents the simple stratigraphy of the area. It also shows the uniformly thick nature of the iron formation members in the district as well as a somewhat abrupt thickening of the formation to the west of the probable fault. The stratigraphy of these precambrian rocks has been described5-&apos; elsewhere and need only be briefly reviewed. Historically, the oldest rocks unit, the Giants Range granite (Algoman) was covered by the Animikie group of sediments (Middle Huronian?), consisting of the Pokegama, Biwabik, and Virginia formations. Outcrops of the Pokegama quartzite are locally distributed along the northern limit of the Biwabik iron formation, but they are too limited to depict on the geologic map of Fig. 1. The effects of the intrusion of several small diabase sills within the Virginia and Biwabik formations are obscure because all of these rocks have been subsequently highly metamorphosed, mainly by the Duluth gabbro. The emplacement of the transgressing Duluth gabbro (Middle Keweenawan) and that of numerous peg-matitic veins in the iron formation8 has resulted in extensive contact and metasomatic metamorphism which has locally reconstituted the previously existing minerals of the Biwabik formation, in large part quartz and magnetite, into a wide variety of silicate mineral assemblages9 that have a profound effect upon the re coverability of the remaining magnetite. The entire region has subsequently been eroded and largely buried beneath Pleistocene glacial deposits. Structurally, the strike of the gently dipping Animikie group generally parallels the elongate outcrop pattern of the Biwabik iron formation on the map of Fig. 1. The Animikie group most commonly dips from 5" to 15" to the south-southeast. In this area, the Duluth gabbro pluton is somewhat sill-like, dipping about 30" to the southeast. Projecting these present structures upward, it seems probable that the gabbro once extended over the underlying Animikie group in the Eastern Mesabi district. SELECTION AND PRESENTATION OF DATA Because of the locally intense metamorphic activity in the district, mineralogical variations within the magnetite-bearing taconites are commonly abrupt, both vertically and laterally. Consequently it is difficult to select a single hole or small group of holes whose cores will be entirely representative of all of the district. Two holes have been selected, however, that in a general way represent mineralogical and textural variations that are likely to be encountered in both the eastern and western parts of the district. These recently drilled holes were chosen for discussion because it was possible to log the core and then to place the sample intervals at stratigraphic boundaries prior to preparation of the core for magnetic tube tests.

Jan 1, 1961

By F. F. Craig

Many full-scale waterflooding operations are preceded by pilot floods, one purpose of which is to provide an estimate of recoverable oil. A laboratory model study was made to determine the influence of the producing wells&apos; effective productivity on the oil recovery efficiency of single five-spot pilots, as well as single injection well pilot floods. The effective productivity is indicated by the value of Condition Ratio, defined as the actual well productivity to that of on undamaged and non-stimulated, normal-sized well in the same formation. The effects of initial gas satrcration and mubility ratio on recovery eficiency were also investigated in this model study. Model test results skowed that at favorable mobiliry ratios, a five-spot pilot flood can provide a direct quantitative estimate of the recoverable oil in the pilot area. If the pilot producer&apos;s Candition Ratio is 2.2 or more, upwards of 90 per cent of the recoverable oil in the pilot area is recovered from the inside producer, regqrdless of the mobility ratio or initial gas saturation. This Condition Ratio can be achieved with preyent fracturing techniques. Model studies also showed that over the range of imposed injection pressure differences and regional pressure gradients normally encountered in field operations, there was no effect on the recovery efficiency of a five-spot pilot waterflood. Model studies of single injection well pilot waterfloods showed that with no initial gas saturation, the total oil recovery at the offset producing wells can indicate the oil recovery possible by full-scale waterflooding. It is essential that the Condition Ratios of the offset wells be above 1.4. If an initial gas saturation exists prior to water injection, the recoverable oil cannot be directly evaluated by a single injection well pilot flood. However, the production per formance of such a flood can be used to provide information on volumetric sweep efficiency. INTRODUCTION Oil reservoirs are conlplex structures and cannot always be fully studied in the laboratory. Therefore, many operators consider it prudent to evaluate a waterflood prospect by means of a pilot flood. Pilot waterfloods generally involve one of two well arrangements: a single five-spot pilot waterflood, involving four injectors and an internal pilot producing well; and a single injection well pilot flood (sometimes called an inverted five-spot pilot) having one injector and four sur- rounding pilot producers. Some pilot floods are composed of multiple five-spot pilot patterns. To yield information applicable to field-wide performance, the pilot must be located in a representative portion of the reservoir. Pilot floods generally are conducted for one or more of the following reasons: (1) to determine whether water could be injected at desirably high rates, (2) to determine whether an oil bank or zone of increased oil saturation is formed by water injection, and (3) to estimate the oil recovery by waterflooding. Many of the early pilot water-floods were conducted for only the first two reasons. As soon as a buzz in oil production was obtained in the pilot, water injection was initiated throughout the entire lease or field. A number ot laboratory studies have been directed toward determining conditions under which a pilot flood could yield a quantitative estimate of the oil recovery possible by full-scale pattern flooding. One of the early studies of single five-spot pilot flooding&apos; showed that well damage to the inside pilot producer could reduce the total amount of oil recovered. In a study of the single injection well pilot flood pattern,&apos; the results indicated that if the model boundaries were no closer than a half-well spacing beyond the pilot pattern, the pilot performance in the laboratory is unaffected by these boundaries. In another study,? he effect of initial gas saturation and mobility ratio on the ratio of production to injection rate for various groupings of five-spot patterns was defined by mathematical and analog methods. In a study4 involving both potentiometric and flow model experiments at a mobiliry ratio of unity, four different pilot patterns were studied. These included a single five-spot, a single injection well pilot, a cluster of four single injection well pilots and six inverted five-spots. In this study the ratio of well diameter to the distance between injection and producing wells was held constant at 1:1000. The effect of the 7 ratio-—the ratio of the pressure drawdown at the producing wells to the pressure build-up at the injection wells on the pilot performance-was studied. The values of 7 ratio ranged from 0 to 0.34. Results showed that both the total oil recovery and the total fluid production from the pilot relative to the cumulative injection increased with increasing values of the 7 ratio. The effect of both the ratio of injection to producing rates and mobility ratio on the oil recovery performance of a liquid-saturated single five-spot pilot flood was studied in a series of flow model tests.5 Rate ratios ranged from one to four, and mobility rates ranged from 0.1 to 10. Resulls of these tests showed that at low rate ratios, the pilot producers may recover up to four times the recover-

Jan 1, 1966

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU&apos; OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l&apos;l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967