Search Documents

By C. W. Hoffman, W. R. Hinken

Probability sizing, a fairly recent development in the field of particle separation, is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages of probability sizing vs. conventional screening methods are: (1) reduced space requirements for a high capacity unit, (2) fewer moving parts, (3) more versatile product sizing selection, (4) reduced maintenance requirements, and (5) lower power consumption. Screening is a necessary part of virtually every crushing circuit. At some stage in the process, particle separation becomes a controlling factor in the operation. The basic type of screen in use today is the vibrating unit, which usually employs a mechanical vibrator of one type or another to obtain sizing and material transportation across the screen surface. The vibrating screen has its limitations and inherent problems. Operators must live with: (1) high maintenance — worn rods, screen cloth, spacers, cross members, chutes, etc., (2) low capacity in relation to floor space requirements, (3) extreme noise levels, (4) high power consumption, and (5) structural problems in the screens and supporting steelwork. All plant operators have become tolerant of these drawbacks through the years, and little innovation has been developed in screening. The vibrating screens in use today incorporate improved metals, more efficient power sources, better lubricants, and increased manufacturing skill, but the basic machine itself remains unchanged. Screening is a relatively small part of most plants' operating expenditures and gets relatively little attention from research and development. The HiProb sizer is a new approach to the problem of particle separation on a high tonnage basis. Developed by Dr. Fredrik Mogensen (president of Fred-rik Mogensen, A. B. of Djursholn, Sweden), this unit has found its primary acceptance in the sizing of wet or dry materials in the fine ranges. Climax has been working cooperatively with Mine and Smelter Supply Company, the United States licensee, on the adaptation of the sizer to obtain consistent recovery at a high tonnage rate on a — 3/8-in. separation. This was a new application for the sizer and opened up a whole new field of problems. Dr. Mogensen's machine utilizes the control of normal probability of falling particles and is designed to eliminate some of the undesirable features of vibrating screens mentioned earlier. The machine is light, compact, consumes less power than conventional screens and has a low noise level. PRINCIPLES Probability sizing is a process designed to allow solid particles to segregate with a high ratio of the materials reporting into their respective size fractions with a minimum amount of misplaced particles. Sizing is defined in this paper as segregation of dry solid particles into fractions of comparable sizes. Probability is usually estimated as the ratio of the number of ways an event might occur vs. the total number of allowable ways. The probability process described depends upon the fact that particles falling through a network will segregate across the sizing surface even though all openings are larger than the particles. The degree of segregation is dependent upon the particle size and the trajectory applied by the sizing network to each falling particle. Specifically, the process utilizes a maze made up of screen cloth to control the path of a particle in free fall as illustrated in Fig. 1. The usefulness of this probability sizing process is dependent upon the degree of efficiency of an effective maze. Primarily, a maze must be extremely flexible to meet the multi-faceted nature of solid particles and, at the same time, the degree of control must be reproducible so that a desired separation is predictable. Dr. Fredrik Mogensen has formulated a maze that is not only flexible and easily controlled, but, mote importantly, easily adaptable to a working machine.

Jan 1, 1970

By Eric R. Jette

In order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned. Heterogeneous Reactions The thermodynamic side of metallurgical reactions has received much attention in the past; the mechanisms, relatively, very little. The main reason for our present lack of information on the mechanisms of these reactions lies in the fact that every one of importance is a heterogenkous reaction; i. e., the substances involved in the reaction exist in more than one phase, while, if we neglect the large amount of work which has been

Jan 1, 1931

By P. K. Weimer

Coinpletely integrated thin-film circuits inco?,porating more than 1000 active and passive elements have been fabricated reproducibly in the laboratory by evaporation of- all components. A 180-stage modified shift register comprising 540 CdSe TFT's, 360 resistovs, and 180 capacitors was deposited upon a glass substrate during one pump-down of the vacuum systeitl. Experimental units have been operated for more than 5000 hr at temperatures uP to 85°C without failure of any slages. The present pupper reviews the charvactevistics of evaporated thin-film transistors (TFT's) and discusses their application to integrnted circuils. INTEGRATED circuits most widely used today are based upon silicon technology, with the circuits formed on the surface of a block of single-crystal silicon1 or on a block of sapphire 2,3 upon which a thin layer of silicon has been deposited. Transistor patterns and interconnections are defined by photographic procedures using photoresist masking. Large groups of transistors are produced in batches which undergo many processing steps, some of which are carried out at elevated temperatures. Passive elements are formed by treatment of the semiconductor surface or are deposited by evaporation alongside the active elements. The size and complexity of the circuits are limited by defects in the devices and by the size of the available single-crystal chips. Capacitative coupling to the semiconducting substrate may also limit useful size and frequency response of the circuits. An alternative approach to integrated circuits is based upon the deposition by evaporation of all circuit components upon a noncrystalline, insulating substrate such as glass.4 Thin-film field-effect transistors,1'6 known as TFT's, can be deposited in large arrays on glass or plastic substrates at the same time the associated passive elements are being deposited. Although still in the research stage the all-evaporated approach is expected to offer certain advantages for many applications. In particular, the use of thin films upon a noncrystalline substrate offers the prospect of producing complex, large-area circuits not now feasible with single-crystal silicon. Important applications of this type include memory arrays for computers and imaging devices for television. The ease with which the evaporated TFT's can be deposited may permit continuous, automated production methods not possible with high-temperature batch processing. Recent advances7'8 in the fabrication of thin-film transistors have led to greatly improved reproduci-bility and life of the TFT's. Experimental circuits having over 1000 active and passive elements deposited upon a common glass substrate are currently being produced in the laboratory. The present paper reviews recent progress in the development of the TFT and in its application to integrated circuits. I) DESCRIPTION OF THE THIN-FILM FIELD-EFFECT TRANSISTOR The TFT is a field-effect transistor of the type having the control gate separated from the semiconductor by a thin insulating spacer. Although its operation resembles that of the silicon MOS transistorg its construction is based entirely on thin-film techniques. Fig. 1 shows a cross-sectional view of an evaporated TFT deposited upon a glass substrate compared with a silicon MOS transistor deposited upon single-crystal sapphire.3 The semiconductor in the TFT is a poly crystal line layer, of a material which can be readily evaporated, such as cadmium sulfide, cadmium selenide,l0 or tellurium." Silicon monoxide layers have usually served as the gate insulator, but other oxides, sulfides, and fluorides may be used. Film thicknesses range from a few hundred to a few thousand angstroms. The source, drain, and gate electrodes in the TFT are of metal. Qpical source-drain gap dimensions are 0.0003 x 0.030 in., with a gate strip whose width slightly overlaps the source and drain. The source and drain electrodes should make low impedance contacts to the semiconductor. With cadmium sulfide films, gold is a satisfactory material for underlying electrodes, while aluminum is preferable for overlying electrodes.12 Considerable variation in design of the TFT is permissible, with the electrodes being

Jan 1, 1967

By W. N. Lacey, R. H. Olds, B. H. Sage

Samules of liquid and gas were obtained from the primary separator of a well in the Paloma field. The volumetric properties of the samples and of six systematically chosen mixtures of the samples were experimentally determined at 100°, 190°, and 250°F. at pressures up to 5000 lb. per sq. inch. From these data the influence ,of pressure and temperature upon the composition and specific volume of the bubble-point liquid and of the retrograde dew-point gas was established, The formation volumes and gas-oil ratios of the rnixtures investigated were calculated on the basis of the plant-product oil, which is defined as the isobutane and less volatile portion of each mixture. The results are presented in graphical and tabular form. The volumetric behavior of the mixture corresponding to that produced by the well at the time of sampling was determined for 235ºF., the reported reservoir temperature, by graphical interpolation of the experimental data with respect to composition and temperature. The results indicate that the well-production mixture probably existed as a gas at its retrograde dew point under the conditions of temperature and pressure believed to prevail in the producing zone at the time of sampling. The effect upon the phase behavim occasioned by the omission from the well-production mixture of certain components of intermediate molecular weight was investigated. In the first case, all of the isobutane and 11-butane, and substantially all of the iso-pentane, were removed from the mixture of trap samples corresponding to the well production. In the second case, all the propane, isobutane and n-butane, and substantially all of the isopentane, were removed. Both modifications led to considerable increases in the retrograde dew-point Pressure at 235ºF.; an increase of 558 lb. Per sq. in. above that of the unmodified well-production mixture in the first case, and an increase of 1208 lb. Per sq. in. in the second. It was concluded that the material? remaining after the removal of certain components of intermediate molecular weight could not be injected back into the reservoir in the saqe proportion in which they were produced without entailing appreciable loss of liquid material through condensation within the formation. Introduction Under the usual conditions of production practice, petroleum arrives at the surface of the earth in a physical state considerably different from that in which it existed in the underground reservoir. The relative rates of production and the properties of oil and gas measured at surface conditions do not constitute, in general, even a qualitative description of the fluids existing in the reservoir. The estimation of reserves and the attainment of optimum efficiency with regard to rate, quantity, and cost of production require accurate data concerning the physical properties of petroleum throughout large changes in pressure and temperature. Many schemes have been devised for predicting the behavior of propane, as it is encountered in nature? but the experimental work upon which these predictions are based has not, for the most part, been extended to the higher pressures that occur in practice, nor do these methods permit, as yet, the estima-

Jan 1, 1945

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" ' also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder')"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder's results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13' and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*' " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.'" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.''' The experiments which will be described in this paper pertain to: (a) the effect of a crystal's shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By F. I. Stalkup

Vapor-liquid phase equilibrium experiments have been conducted in a static equilibrium cell on mixtures of a light, 45 API stock- tank gravity reservoir fluid and a rich hydrocarbon gas containing approximately 55 mole per cent of intermediate hydrocarbons. Both apressure-vs-composition study of the gas and a simulated reservoir fluid, and a multiple-batch contact simulation of the condensing-gas-drive oil recovery process were performed. In the latter experiments equilibrium gas and liquid compositions were analyzed. Also, conventional, "condensing-gas-drive", long-tube displacement experiments of the reservoir fluid and gases of various richness were performed. The results of these experiments could not be satisfactorily interpreted by the conventional pseudo-ternary-diagram representation of multicom-ponent phase behavior. The results seem to be explained better by considering a bubble-point surface and a dew - point surface joined in a plait-point locus. Portions of the plait-point locus cannot be "seen" directly by the rich hydrocarbon gas because of curvature of the dew-point surface. In such a system, continuous injection of the rich gas over stationary reservoir fluid might form a zone of contiguously miscible compositions from pure rich gas to pure reservoir fluid by: (1) saturating the reservoir fluid with injected gas to the bubble-point surface; (2) creating by mass transfer with fresh injected gas a path of contiguously miscible compositions along the bubble - point surface to the plait-point locus; and (3) creating by mass transfer with additional injected gas a path of gas compositions along the dew-point surface up to the point where direct miscibility results between dew-point fluid and the injected rich gas. INTRODUCTION The use of the pseudo-ternary-phase diagram to illustrate miscible displacement phase behavior has been discussed by several authors.5,7 Such a representation of phase behavior is not rigorous, but the ternary diagram nevertheless gives a qualitative picture of what actually occurs in a miscible displacement process. Fig. 1 is a typical illustration of miscible displacement phase behavior by a ternary diagram. The multicomponent hydrocarbon system is divided into three pseudo-components: a light fraction containing methane and nitrogen, an intermediate fraction containing ethane through hexanes plus carbon dioxide, and a heavy fraction containing heptane and heavier components. A two-phase region is bounded by a dew-point curve and a bubble-point curve, which are joined at the critical point. The concept deduced from such a representation for miscible displacement by a condensing-gas-drive process is as follows: a rich gas G, which lies to the right of the limiting tie line through the critical point C, is injected into the reservoir and contacts reservoir fluid L, saturating the reservoir fluid to give bubble-point fluid L1 and equilibrium dew-point gas GI. Continued injection of rich gas changes the composition of the saturated liquid L1 through a series of liquid compositions lying along the bubble-point curve, until the critical composition C is reached, at which point direct miscibility with the rich gas is achieved. Some equilibrium gas with compositions lying along the dew-point curve from G1 to C is also formed in this process. Thus, continuous injection of rich gas forms a

Jan 1, 1966

By Robert E. Hoffman, John B. Hudson

The self-diffusion coefficient of pure lead has been measured at five pressures between atmospheric and 40 kb. over a temperature range of about 150°C near the melting point at each pressure. Measurements were made using a radiotracer technique, samples being sectioned electrochemically after the diffusion anneal to determine the diffusion penetration curve. Pressure was applied in a "belt" type pressure device similar to that used by Hall et al., in the diamond synthesis. The self-diffusion coefficient, D, can be represented by an equation of the form at constant pressure, and an equation of the format constant temperature. An apparent correlation between the effects of pressure on self-diffusion and on the melting point of the material observed by Nachtrieb et al., at pressures below 10 kb. was found to be only approximate as measurements are carried to higher pressures. OVER the course of the past 30 years a large number of studies1-' of the rate of atom movements in solid metals have been carried out. These studies have in general been aimed at increasing the understanding of the detailed atomic process by which atom movements in metals can take place. The largest portion of these studies consisted of measurements of the self-diffusion coefficient, D, as a function of temperature. From such studies con- siderable information regarding the energetics of the motive process has been deduced. Recently such measurements have been extended to the pressure dimension. However, the existing work in this area is scanty and has in the past been limited to the pressures attainable in oil or gas bombs—i.e., up to about 10 kilobars (kb). In the present work, the self-diffusion behavior of pure lead has been investigated using the "belt" type high-pressure apparatus designed by Hall7 over a pressure range from atmospheric to 40 kb at temperatures extending over about a 150°C range close to the melting point at each pressure.

Jan 1, 1962

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By W. A. Griffith

Fractional replication of factorial design, a general method for planning experimentation and for analysis of data obtained, is described as applied to a flotation investigation. This method leads to determination of optimum process conditions with minimum experimental effort. Its advantages over simple factorial design are demonstrated. A METHOD for planning experimentation and for analyzing the data secured will be demonstrated. This method, termed fractional replication of factorial design, employs a relatively small number of individual experiments to determine which of a large number of process variables are controlling, to determine which combination of levels of these variables is most likely to produce optimum results, and also to predict what results will be obtained with a particular combination of conditions not already tested. Although the general method is not new, having been developed by Finney in 1945,' the extent to which it can improve the effectiveness of applied research generally has not been recognized by metallurgists. The fractional replication procedure is particularly useful in flotation experimentation and an example from such an investigation will be used in the paper. However, it has equal value in any investigation in which similar experimental difficulties are encountered. In developing a flotation process for a particular mineral separation, the investigator is inevitably confronted with the following difficulties: 1—There are a large number of potentially important process variables. 2—Results of individual experiments are not highly reproducible, due in part to the difficulty in precisely controlling all the variables. 3—Considerable effort is expended in conducting individual experiments. 4—There are practical limits on the number of individual experiments which can be made. In situations of just such a type, modern statistical methods of planning experimentation and analyzing data have their greatest value. Applications of one such technique, called factorial design, to problems of this type have been described by Dorenfeld and others.'-' The simple factorial design is an efficient procedure when the investigator hopes to provide a comprehensive understanding of the effects and interrelationships of a small number of variables over a limited range. In applied research, this is seldom the main objective. Rather, the investigator usually wishes to determine which of the many potentially important variables are in fact controlling, which levels of the controlling variables will provide opti- mum metallurgical results, and what these results will be at optimum conditions. Interest in detailed trends is limited to the controlling variables and to levels in the region of optimum conditions. Simple factorial design has serious deficiencies for such objectives and is not the most efficient method of experimental design. Deficiencies of Factorial Design In a simple factorial design, an experiment must be made at every possible combination of each level of every variable, once these have been chosen and the levels of each to be included have been decided upon. As the number of variables or levels of each increases, the experimental program quickly reaches prohibitive size. For example, an investigation of only four variables, each at four levels, requires 256 individual experiments. Often upon completion of such an extensive program, it is found that one or more of the variables has metallurgically unimportant effects or that a poor estimate has been made as to the appropriate range of levels to be investigated. The result is that only a small proportion of the data obtained falls in the range of real metallurgical interest. Indeed, it frequently can be anticipated that certain combinations of levels of variables will not produce results of interest, but they still must be included so that the essential balance, or orthogonality, of the design will be retained. It may be true that factorial design will provide the greatest amount of information from a given number of experiments, but it does not necessarily follow that it will lead to the desired information with a minimum number of experiments. Much of the information provided may be of little value. Advantages of Fractional Replication The disadvantages of simple factorial design are overcome to a great extent by a modification known as fractional replication. This is a technique for sampling systematically the potential data of a full factorial experiment, that is, the data which would have been obtained if the complete factorially designed program had been completed. Only a fraction of the total array of experiments is made, but the experiments are chosen in such a way that the important advantages of factorial design and the accompanying analysis of variance are retained. The data obtained from the first group of experiments are used to determine which of several variables are controlling and which levels of these variables are most likely to produce the desired result. Unimportant variables and levels of variables then may be

Jan 1, 1956

By Harry H. Angst, Reuel A. Cochrane

THE successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. ROCK FORMATIONS At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in-the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1941

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By E. R. Stover, J. Wulff

A tentative 870°C isothermal section, the solidus equilibria, and the solubility of Tic and graphite in the nickel solid solution have been determined with arc-cast specimens. Each of the Ni-Ti intermetallics forms two-phase fields with Tic; only Ti,Ni has a measurable solubility for carbon. A quasi-binary eutectic exists between Tic: and a titanium-rich nickel solid solution; ternary eutectics occur on either side, with TiNis or with graphite. Graphite is in equilibrium with a nickel solid solution containing a ratio of Ti/C which increases below the solidus. DURING the past decade, titanium-carbide cermets containing nickel or cobalt alloy binders have been widely studied for high-temperature and wear-resistant applications. Recent work has emphasized control of the carbide grain size and distribution2's and the thermal exparision match between the phases/ The present study was initiated to determine the phase compositions during the sintering or infiltration process, and during subsequent heating. Although the effects of additives and impurities in commercial compositions are important, it was necessary to consider first the pure ternary, Ni-Ti-C. Emphasis was placed on the nickel corner, since the nickel solid solution is the continuous phase in compositions having highest strength. Early metallographic work by Zarubin and Molkov- showed that solid solubility at either end of the section Ni-Tic is small. Edwards and Raine reported that nickel dissolves between 3 and 5 wt pct Tic at 1250° C, on the basis of microstructures of annealed, vacuum-melted powder mixtures. Although the solubility of nickel in Tic has not been measured, Tic formed by the menstruum process in liuid-iron solution contains as little as 0.06 wt pct Fe. BINARY SYSTEMS The most recent determinations of the three binary systems are summarized in Fig. 1. Titanium carbide (6) is predominant among the binary phases, and it melts above the boiling point of nickel. The Ni-C binary is based on separate liquid solubility' ) and solid solubilitylo measurements. The eutectic temperature, 1328OC, is taken from the solidus determination described below. However thermal analysis data by Morrogh and williams also show eutectic arrests in this vicinity in the absence of supercooling. The Ni-Ti binary is taken from the work of Poole

Jan 1, 1960

By G. Derge, W. Peifer, J. H. Richards

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more- difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in inter- mediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, of ten called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1985

By Samuel G. Vera

INTRODUCTION The Climax Mine is a property of Climax Molybdenum Company, a division of AMAX Inc. Climax is located in the central part of the Colorado Mineral Belt on the west slope of the Tenmile Range, Lake County, Colorado at 3,425' m. above sea level. Climax Mine, the largest single producer of molybdenum in the free world, has been a cornerstone of mining in the State of Colorado for many years. Before molybdenum was known, the early hunters of gold and silver laid their hands on the outcrops of the Climax deposit and left it as low quality lead or graphite without much value. Today, 44,000 TPD of ore is extracted from the heart of Bartlett Mountain. The molybdenum, separated from the ore, is vital for mankind, being used for everything from fertilizer to fine components of aerospace ships, because of its valuable physical and chemical properties. The operations at Climax have never remained static. Constant demand for the "gray gold", and technological advancements, have converted Climax into an "open book of technology", where learning the still-hidden secrets of mining is a continuing process. (All figures related to tons are metric tons) BRIEF HISTORY The mine produced its first molybdenum ore in 1918. It was shut down in 1919, resumed production in 1924, and has been in continuous production since that time. During World War 11, a peak of 20,000 tons per day was reached, then tonnage dropped from 1945 to 1950. Since 1951, production has been in- creasing, reaching a peak of 46,000 tons per day during the month of June, 1980. Early mining used shrinkage stoping. Block caving using the grizzly system was introduced in the early 1930's. Caving methods were improved through empirical studies of rock behavior and by trial and error, evolving a very efficient mining method by the late 1940's. This form of continuous retreat panel caving, with small modifications, is still used today, and has made the Climax Mine one of the biggest underground mines in the world. The Climax Mine, synonymous with molybdenum, was essentially an underground mine until 1973 when the open pit was introduced. Since then, both mining methods have operated successfully. Current production is 60% from underground, and the remaining from the open pit. Climax has been in continuous operation for 56 years, and as of December 31, 1980, more than 386 million tons of ore have been mined. The orebody is not fully defined, and at the present mining rate, the known life span of the mine will be to the year 2020. GEOLOGY The Climax deposit is a large low-grade porphyry molybdenum deposit somewhat similar to porphyry copper deposits, with a well- mineralized quartz molybdenum stock work sys- tem. It lies within the pre-Cambrian granites and schists and the Tertiary Climax porphyry. The age of mineralization is thought to be mid-Tertiary and is characterized by fracture filling and replacement through silicification. The main economic mineral is molybdenum, with pyrite, cassiterite and wolframite as by-products. Fluorite and topaz also occur, but are not recovered at this

Jan 1, 1981

By F. X. Tartaron

This paper deals with basic physical phenomena, which when combined and interpreted, lead to the same mathematical equations that describe comminution phenomena. Thus, a physical model is described that corresponds to the mathematical model presented in the writer's previous papers. '12 In the mathematical model, the energy consumed in breakage is related to the volume or weight of material broken and the size of particles broken. The equation E=2.303 Ck-a log x1/x2 was derived by multiplying the volume or weight of each size in an ideal Gates-Gaudin-Schumann size distribution by an energy factor. The product of these two factors gives the energy distribution among the different sizes in a single size distribution. The energy of breakage of a specific constant weight of one size distribution to another size distribution is given by the equation E = constant/kn-1. In this case, where the volume or weight is constant, the energy is proportional to the size factor 1/kn-1. In what follows, a physical theory will be presented showing that the energy consumed in comminution is proportional to the volume or weight of the material broken and to the reciprocal of the size of this material raised to a constant exponent. THE VOLUME FACTOR The atomic theory of matter reveals that in solids, atoms or ions are arranged so as to be in equilibrium at specific distances from one another. Although the atoms or ions are oscillating, there is a definite determinable mean distance between them and this distance is a balance between repulsive and attractive electrical forces. It therefore requires force to separate the atoms or ions and when an outside force is applied, it first produces strain in increasing the distance between the atoms or ions. This strain increases to the breakage limit on application of sufficient force. In brittle materials, there is negligible plasticity and when an elastic limit is exceeded, breakage takes place. The work done is the force applied per unit area times the cross sectional area of the ideal particle multiplied by the maximum strain per unit length at right angles to the area times the length of the particle. Thus the work done is proportional to the area times the length, which is equivalent to the volume of the ideal particle. If more than one feed particle is considered broken, each particle must be subjected to sufficient strain so that the breakage limit of its contained atoms or ions is reached in order for the particle to be broken. Thus, the energy of breakage is proportional to the total volume of the particles broken. If the particles are of different sizes, the size factor must be included to get a correct determination of energy of breakage. In the preceding, it has been assumed that there is a constant binding force between the atoms throughout the volume being strained. This, of course, is not true. It is known that there are many irregularities in the structure of matter and the binding force differs markedly in different portions. But the differences are only discernible by examining extremely small subdivisions of matter. In one order of magnitude of volume, cracks can be discerned separately from non-cracked neighboring material. In a smaller subdivision of volume, lattice dislocations can be isolated. When these situations are brought into focus, mechanisms of their behavior can be learned, leading to a fuller understanding of phenomena that occur in larger scale subdivisions of matter. Very often, however, the mechanisms that operate in small scale subdivisions have negligible effect in those of large scale, and there still is a place for deriving a mechanism for large scale conditions. The quantum theory is extremely valuable for use with photons and electrons, but is of negligible use with ordinary atoms and molecules. This paper deals with relatively large scale subdivisions of volume present in comminution phenomena. Hence, the effects of cracks, lattice dislocations, misplaced atoms, etc., are smoothed out in an average, constant for each relatively large subdivision of volume. This attitude is supported by experience. If two 10 cc samples of the same ore were ground identically, the same product would be obtained. However, if two samples, each a cubic micron, were conceived to be broken, then one sample might contain a crack and the other not, hence a different product would be obtained. Experience shows that ordinary samples used in comminution, behave as though no irregularity existed

Jan 1, 1964

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By Earl S. Greiner, Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two monographs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken. Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon. Discussion oF Continuous Series It has often been said in print that the iron-silicon alloys form a continuous series of solid solutions from 0 to 15 per cent. silicon. This claim the authors are inclined to doubt: first, because the alloys from 0 to 4.25 per cent. silicon are ductile and malleable at atmospheric temperature, while those with 5 per cent. or more of silicon are comparatively hard and brittle. Furthermore, the alloys with more than 4.25 per cent. silicon are comparatively hard and low in ductility at atmospheric temperature, but become much more ductile when heated slightly. It is well known, for example, that the alloy containing 4.75

Jan 1, 1930

By Edward Estabrook

THE Salt Creek oil field in Natrona County, Wyo., is the largest pool that has been found in the Rocky Mountain region and one of the largest in the United States. Many features of its production records are of peculiar interest, because of the unusual slowness with which it has been developed. This paper is published by the permission of the Midwest Refining Co., whose records have been freely drawn upon. Many mem¬bers of the Midwest organization have assisted in the collection of the material, but Messrs. F. E. Wood and L. E. Smith have been particularly helpful. The Salt Creek oil field is situated on a great dome with a closure of about 1500 ft., which rises at the northern end of a long anticline extending north-northwest by south-southeast for fully 25 miles. The productive area includes parts of townships 39 and 40 north and ranges 78 and 79 west of the sixth principal meridian. The Teapot oil field occupies a minor dome at about the center of the same anticline and adjoins the Salt Creek oil field on the southeast. The Teapot Naval Reserve includes the Teapot Dome and about 760 acres of the Salt Creek dome. In this paper, the Salt Creek oil field will be considered as' including all of the dome, except that part which lies within the Teapot Naval Reserve and the area west of the dome where oil is produced from shale crevices.

Jan 9, 1925