Search Documents

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be done by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts.

Jan 1, 1944

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through inter- change of knowledge. This can best be done by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts.

Jan 1, 1946

By Jack Fox

Although this is going to appear in the December Issue of &E, it is being written long before the end of the year. December, of course, is the time for a summing up of the year's activities. Perhaps, the best way to begin is to report on what went on at the SME Board of Directors Meeting in St. Louis on October 20. This won't be a chronological report, and I shall take time to comment on some of the items we cover as we go along. You should be encouraged to know that your Directors take their duties seriously. Of the 21 current Directors, 19 were present, and three of the new 1971 Directors came to observe what goes on at an SME Board Meeting.

Jan 1, 1970

By Bruce A. Kennedy

The place of the young engineer in the mining industry has been the subject of a large number of keynote addresses, magazine articles, and papers in the past year. One of the best of these was the keynote address given by Mr. J. C. Kinnear, Jr. at the Fifth Annual Intermountain Minerals Conference in Vail. Colorado. Mr. Kinnear presented as part of his address the statistics of a Canadian survey Instigated to find out why young engineers and geologists are leaving the mining industry. The results of the survey showed four main reasons for leaving: 1) insufficient money 2) slow promotion 3) lack of association with senior engineers, as well as insufficient opportunity to keep abreast of technological development 4) geographic isolation

Jan 1, 1970

By M. S. Klima, P. T. Luckie

An evaluation of the operating performance of a recently designed pneumatic centrifugal classifier is presented. This classifier has been modified from a separate air and feed input design to an entrained solids in air feed input. The evaluation first required determining the size distributions for the three streams (feed, fine, and coarse). Using size distribution data and mass flow rates, a size selectivity curve was calculated for each operating condition tested. This curve, in turn, was characterized by appropriate selectivity parameters (i.e., the equiprobable or cut size, the sharpness index, and the apparent bypass values). The variation of these parameters with classifier operating conditions was examined. From these evaluations, the "best" operating conditions for the classifier were then determined.

Jan 1, 1985

By John V. Beall

As Mother Nature arranged it, the hottest potential mineral target in the country today, the Stillwater complex had to occur in a spectacular natural setting-the north margin of the Bear Tooth Mountains of Montana. What more appropriate backdrop for the August 17-18 field hearings of Senator Frank E. Moss (D-Utah). His subcommittee, on Minerals. Materials and Fuels, heard 37 witnesses ponder the value of minerals vs esthetics or other uses of federal lands. On August 17, four Army Hueys swept the senatorial party, the press, Forest Service Officers and such distinguished witnesses as Montana Governor Forrest H. Anderson over the Custer-Gallatin National Forests, besting the thin air of 10,000 ft p1us, they set down on Iron Plateau.

Jan 1, 1971

By Christopher Haycocks, J. Richard Lucas

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine design, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environmental considerations and the visible limitations of other energy sources.

Jan 4, 1973

By I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) has been successfully applied to the recovery of gold and uranium from the residues of Witwatersrand ores. Good overall recoveries have been achieved for particles as small as 12µ, and finer particles of uranium minerals are recovered when present as inclusions. The best results were obtained with a matrix of soft-iron balls 6 mm in diameter. However, pilot-plant tests drew attention to a major defect of the machine: the matrix could be blocked by wood chips and ferromagnetic particles. This problem was overcome by the incorporation of a modification that allows the balls to be discharged from the rotating annulus. Two full-scale units that incorporate the modification have been installed.

Jan 1, 1980

By D. W. Duncan, A. Bruynesteyn

An ore containing chalcopyrite was microbiologically leached in 6 ft columns at particle sizes ranging from -2 +1 ½ inches, to -3/8 + 3/16 inches. The rate of leaching increased exponentially as the particle size decreased. The controlling factor was the active leaching volume made up of the particle surface area and the depth of penetration of the bacteria and leach liquor into the particle. This volume became an increasingly larger part of the total volume as the particle size decreased. The sample under test leached poorly at larger particle sizes and it was calculated that under commercial conditions, it would produce at best a pregnant solution containing 100 mg/l (0.2 lb/ ton) of copper per 100 ft of dump height.

Jan 1, 1974

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 12, 1978

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 1, 1979

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

By B. G. Bunting, J. H. Johnson, H. J. Schock

This paper describes an experimental method for monitoring diesel-generated exhaust gas pollutants in a deadended drift to assess the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 32 m long and slightly downsloping, with an everage height and width of 2.4 and 8.6 m, respectively. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generate pollutants. Induction ventilation appeared to be the least effective of the three methods examined.

Jan 1, 1982

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By H. B. Pulsifer

ABOUT 15 varieties, or modifications, of the best magnesium available were prepared and subjected to etching tests, then examined for microstructure. Of the 30-odd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressure cold metal deforms slightly, then shears to fracture without plastic flow: The chief structural features of magnesium are presented in two reduced photographs and 30 photomicrographs.

Jan 1, 1927

Division of Geology, State of Tennessee, 401 Seventh Ave, North, Nashville, Tenn. Walter F. Pond, State Geologist A selected list of Bulletins available: Bulletin 1(B), Bibliography of Tennessee geology (1911); 2(A) Outline introduction to mineral resources (1910), 2(D) Marbles (1911); 2(G) Zinc deposits (1910), 16, Red iron ores of east Tennessee (1913), 22, Geology and natural resources of Rutherford County (1920), 24(A) Geology and oil possibilities of parts of Overton, Clay, Pickett and Fentress counties (1920); 24(B) Oil and gas resources of northeastern Sumner County (1920), 26, Mineral resources of Waynesboro Quadrangle (1921); 28, Marble deposits of East Tennessee (1923), 29, Magnetic iron ores of east Tennessee (1923), 31, Zinc deposits of east Tennessee (1923), 33, Tennessee coal fields, 37, Geology and mineral resources of Hardin County, 38, Stratigraphy of the Central Basin (in press), 39, Brown iron ores of the Eastern Highland Rim (in press) From 1911 to 1919, inclusive, volumes were issued annually on The Resources of Tennessee Only a few of the separate papers contained in those volumes are now available Vol. 2 (1911): No 1, Explosions of coal dust in mines, and other papers, No. 4, Lignite and lignitic clays in west Tennessee, and other papers; 5, The growth of knowledge of Tennessee geol¬ogy; 9, The valley and mountain iron ores of east Tennessee, 10, The iron industry of Lawrence and Wayne counties, and other papers; 11, Barite deposits in the Sweetwater district, and other papers, 12, The iron ore deposits in the Tuckalioe district, and another paper Various oil maps (15 to 40 cents each) and traverse maps of counties (25 cents and 31 each) can be had, as well as pertinent U. S topographic maps.

Jan 1, 1933

By A. W. McReynolds

E. OROWAN*—I observed the phenomenon of jerky yielding many years ago with zinc25 and cadmium single crystals. A significant point was that the jerks occurred not only when the stress was raised but also (sometimes, after a pause of many minutes during which no trace of creep was observable) at constant stress. The phenomenon may be closely linked with the inertia of the testing machine and of the specimen, although the inertia alone cannot account for it. If, during the test, the resistance of the material to plastic deformation suddenly diminishes while the applied force remains constant, a sudden deformation follows until the yield stress has risen, by strain hardening, to the level of the applied stress (= the value of the previous "upper yield point."). When this is reached, the rate of deformation has attained a maximum value because, up to this moment, the applied force was higher than the plastic resistance of the specimen, and the difference was used for accelerating the moving parts of machine and specimen. The kinetic energy accumulated is now transformed into plastic work by further deformation; that is. the deformation overshoots the point at which the plastic resistance equals the applied static force. When the kinetic energy has been used up, therefore, we are left with a specimen the yield stress of which is higher than the applied stress, and no further deformation can occur (apart from a little creep) until either the applied stress has been raised to the new yield stress level, or the yield stress has fallen by thermal recovery to the level of the applied stress. While this occurs, a new upper yield point can develop, for example, by precipitation.26

Jan 1, 1950

By P. Barnes

The sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus he obtained of the facts embodied in the statement as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying arid compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

By P. Barnes

THE sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus be obtained of the facts embodied in the statement, as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying and compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879