Search Documents

By M. C. Flemings, P. J. Ahearn

Dendvite morphology of unidirectionally solidified Sn-12 pct Bi alloy was determined with the aid of X-ray and macroetch techniques. Columnar growth direction (growth direction of primary arms) in this alloy is [110]; secondary arms grow in the [lii], [111), and [112] directions. Interstices between [112] dendrite arms fill in during early stages of solidification so that well-defined (110) planes are seen in the final structure (parallel to the heat-flozo direction). Similarly, interslices betweex the [111] secondary arrlls fill in to form (112) planes, and interstices between [1111 ] arms fill in to form (112) planes. DENDRITE morphology in alloys is conveniently studied in unidirectionally solidified castings. In this type of solidification, heat is extracted from a single chill surface of the casting while other surfaces are insulated. Solidification progresses from the chill and results in cast grains that are columnar with the long axis of the grain perpendicular to the chill. Dendrite morphology is conveniently studied by examination of etched surfaces parallel and perpendicular to the chill, as previously described.'" Experimental studies on the growth direction for tin are in general agreement. The major growth direction is [110]:-' although this is altered somewhat by supercooling. In one study, tin dendrites pulled from a supercooled melt had a growth orientation 12 deg away from the [110] direction toward the [002] direction.' This orientation could be changed back to the [110] or close to the [110] direction by changing the tempera- ture gradient in the melt. In a study using autoradio-graphic techniques, (111) directions were shown to be directions of preferred growth in addition to the [110) direction.7 PROCEDURE The samples employed in this study were cut from 12 pct Bi-88 pct Sn castings, 1.5 in. in diam and 3.5 in. tall. The casting procedure consisted of heating the charge to 390°C and then pouring the molten alloy directly into a gypsum sleeve mounted on a massive copper chill. Specimens were cut from the ingot, mounted, polished, and etched with Taffs reagent [FeC13 .6H2O, 2 g; HC1, 5 cu cm;H20, 30 cu cm; CzHaOH (95 pct), 60 cu cm].' The dendritic pattern was clearly visible after etching. Photomicrographs at about 8 and 35 times were taken on surfaces parallel and perpendicular to the chill. Laue back-reflection patterns were obtained from three different columnar grains in a singIe polished face 2 in. from the chill. The cut face was polished and positioned in the beam of a Laue camera, so that diffraction occurred from a single dendritic grain. The resulting diffraction pattern was interpreted to determine crystal log raphic orientation in relation to the heat-flow direction and in relation to microstruc-ture of the given grain. RESULTS Fig. 1 shows a horizontal and vertical section of the columnar structure, at low magnification. Light regions are rich in tin, and darker regions tin-poor; the primary phase is tin-rich a phase. The two sections shown were taken orthogonally from the same metallographic specimen. It is readily seen from Fig. 1 that the dendrites have

Jan 1, 1968

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By R. A. Morse, C. R. Stewart, F. F. Craig

This paper preFents the results of a series of model flow test on a number of large limestone cores, having different pore configurations. For limestone cores having substantially sandstone type porosity, the production characteristics for solution and external gas drives are similar. For cores whose pore spaces were microscopically heterogeneous (i.e., consisted of combinations of solution cavities, matrix. and fissures), the production characteristics lor solution and external gas drives vary widely. The degree of divergence between gas-oil relative permeability relationships calculated from solution or external gas drive tests is an indication of heterogeneity of rock pore structure. The results of water floods on cores depleted by solution gas drive for each of these two general types of limestone porosity are also shown. Generalizations are made on the water flood recovery that could be expected from each of these two types of limestone porosity. The similarity between solution drive field performance and model solution drive performance on cores from the same formation is shown for several cases. This indicate? the feasibility of predetermining limestone field performance from such large core tests. Photomicrographs of plastic-impregnated rock thin sections of the samples tested are presented as an aid in understanding the flow test performances. INTRODUCTION During the past 15 years. reservoir engineers and research workers have developed methods of testing rock and fluid samples and applying the results, through calculation, to allow reasonably satisfactory predictions of oil recoveries and performances to be expected in sandstone oil recervoirs. It has been determined that representative fluid flow data can be obtained on rock samples as small as three-fourths in. in diameter by one in. long in most sandstones. However, little has been accomplished toward the laboratory determination of fluid flow characteristics in limestones. There has been a great deal of speculation as to the influence of variations in pore size, shape, and degree of interconnection upon oil recovery processes, and a great deal of thought has been given to the interpretation of limestone field perfomance. It has been generally recognized that predictions of reservoir performance based on oil displacement tests on small limestone core samples the size of those used for sandstone tests can often be misleading because of the improbability of obtaining a representative sample in such a small core. Obviously, if there are present in the rock, pore openings of the magnitude of 1/16 in., or fractures or solution channels up to one in. or more in length, it will be impossible to cut any sample less than one in. in any dimension which would represent the flow geometry of the gross rock system. In some formations, the individual openings in the rock are of such size that it would be impossible to obtain a good sample of the flow system even in the total core available from conventional-sized well cores. However, by increasing to the maximum the size of the sample used, it should be possible to obtain representative flow data from the majority of limestone reservoir materials which can be used for prediction of future primary production performance or response to be expected from secondary recovery measures. The only alternatives to obtaining good laboratory test data to serve these purposes are extrapolation of primary performance data obtained by partial depletion of a field, or obtaining information from pilot tests. It has been shown previously, and will be demonstrated further by the work reported in this paper, that extrapolation of solution gas drive performance for an estimate of gas injection response can be very misleading in reservoirs of heterogeneous type porosity. Although it cannot be expected that laboratory information can ever eliminate the necessity of small-scale pilot operations, it is expected, as is now the situation with sandstone reservoirs, that laboratory tests should provide reliable information for screening of

Jan 1, 1953

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By R. J. Cowan

In the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as '' Catalytic" "atomic," "nascent" and "activated," in an attempt to describe the process. These words are used indiscriminately. For instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process. Reactions at Metal Surfaces For many years attention has been directed to the consideration of reactions that occur on metal surfaces. When heated under the influence of certain metals a complex gas will be broken down and one of the constituents thereof usually found to be very active chemically in combining with the metal. The process of nitriding is an example of this type of reaction. In this case ammonia (NH3) breaks down at the metal surface and the nitrogen which is thus liberated reacts with the surface to form a nitride whereas molecular nitrogen not so liberated is inert and will not react chemically with the metal. Whatever term or terms may be used to describe such reactions, the fact remains that they are highly important and valuable in their commercial applications. Since the metal surface plays so important a part in these reactions, it is evident that any accumulation of reaction products thereon interferes seriously with the progress of the reactions. For this reason it is desirable to remove all such products as rapidly as they are formed in order to bring active gas into contact with the surface and thus facilitate the desired reactions. This is accomplished best by conducting the operation in a continuous manner, thereby causing the reacting gases to pass over the

Jan 1, 1931

By F. W. Bremmer

The experiments described in this paper constitute the preliminary work of an investigation outlined to determine the combined effects of steam and temperature on the endurance properties of certain steels. Essentially of a fundamental nature, it was found necessary, in order to make the investigation comprehensive, to test materials treated to give a wide range of properties. The work reported deals chiefly with nickel steel with one series of tests including nitriding steel. Such a study involves numerous variables, and requires an endurance-testing machine of rather special design. Testing Machines The testing machines used were designed by C. E. Weaver;l they are a modification of the White-Souther and McAdam types. Each was driven directly by an individual 1/2-hp. 115-volt direct-current motor, running at a speed of 2200 r.p.m. Fig. 1 shows the assembly drawing and Fig. 2, a photograph of one of the machines. Specimen B is held by the rotating specimen holder A inside the steam box F, which is closed at the top by a tight-fitting, elliptical cover G. The load is applied to the specimen through the rod D and bearing C. E is an oil pipe leading fromthe lubrication system to the bearing C. The steam, which comes from the power house, is admitted through an inlet (not shown in Fig. 1) at the side of the box, the drain being at the bottom. Steam packings were placed around the rod D and the rotating shaft at H, from which the water was drained by means of a vacuum, which usually showed a gage reading of about 10 in. The temperature was measured by a mercury thermometer, and the pressure by a steam gage. Method of Applying Load After the motor has been started and the specimen as a consequence put in rotation, the load is applied by placing the foot pedal A (Fig. 2) in contact with electromagnet B, the winding of which is connected electrically in series with the motor. This operation releases the support under the weights that constitute the load. By this means the load

Jan 1, 1930

By L. F. Engle, M. A. Hewedi

SUMMARY Initial interest in using solutions of ammonium salts to leach native copper was documented in notes from an AIME meeting in 1871; By 1916-1917, application of the NH3-CO2-H2O system to recover nonferrous metals attained commercial significance, when it was used as a process for copper recovery by Kennecott Copper Corporation and Calumet & Hecla Mining Company. The Caron work in the early 1920s, Freeport Sulphur Company’s achievements leaching Cuban laterites during World War II, out- standing accomplishments in both eastern and western Canada, recovery of manganese related to the work of Dean -- all serve as landmarks as this One Century Review surveys a base for future technology. Current emphasis on compatibility of metals-producing systems with the need to meet environmental protection criteria provides special encouragement to researchers and engineers to find accept- able ways of recovering metals. The ever-present demand of management to design, build and operate facilities on a profitable basis provides additional impetus to apply information from the technical literature to that need. Examination of the general approach to this paper will reveal much that is firm and positive with respect to empirical results -- extractions, recoveries, amenability to familiar proven equipment and materials of construction common to the industry. Although there are many references, there are gaps in the basic scientific data that if filled could lead to even more usefulness; the paper attempts to indicate where further information is needed.

Jan 1, 1973

By Burnham E. Field

TAE chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is-one of the more important forms of corrosion-and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, 'the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling. this acid under plant conditions.1 The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others,' but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum.3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By B. H. Kear, S. M. Copley

A dynamic theory of precipitation hardening in alloys containing cohevenl, stvess-.free, ordered particles is developed. The yield stvess is predicted from the stress dependence of the plastic strain vale, which is related to a derived dislocation velocity-stress function. The theory is shown to predict the magnilude and temperature dependence of the yield stress of a commercial nickel-base superalloy as well as many details of its slip structure. GLEITER and Hornbogen have developed a theory of the yield stress in alloys hardened by coherent, stress-free ordered ptrticles based on the observation that dislocations (b = a/2 (110)) glide in pairs.' When a dislocation pair shears through an ordered particle, the glide motion of the leading dislocation is impeded since it must create antiphase boundary (APB), whereas the motion of the trailing dislocation is assisted because it annihilates APB produced by the first one. Taking into account the APB energy, the size, and spacing of the particles, G-H predict the observed yielding behavior in Ni/18.8 Cr/6.2 A1 alloys composed of a matrix phase y '(nickel-solid solution) and particles of y' (basically Ni3A1). The G-H theory, as well as all previous theories of hardening by coherent ordered particles, do not include the details of dislocation motion; the present dynamic theory is an attempt to overcome this limitation. In the dynamic theory, the yield stress is predicted from the stress dependence of the plastic strain rate, which is related to a derived dislocation velocity-stress function. This function can be evaluated if the structure of the alloy, the APB energy of the ordered phase, and the characteristic drag or frictional stresses of the matrix and precipitate phases are known. The theory is shown to account for the observed temperature dependence of the yield stress in a commercial nickel-base superalloy. 1) NICKEL-BASE SUPERALLOYS Although their compositions are complex, the nickel-base superalloys have remarkably simple structures. A detailed examination of the commercial superalloy

Jan 1, 1968

By A. Stanley, J. C. Mead

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus % in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9 1/2 in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9 1/2 in. bed sinters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite recovery). These tests have proved successful in increasing ilmenite recovery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was plus from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By L. E. Young

THE progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. INTRODUCTORY STATEMENT AND SIGNIFICANT POINTS IN PROGRESS Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: I. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods and the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, considering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for the mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics, petroleum engineering, petroleum technology, ceramics and so forth. 7. There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1947

By Carleton Ellis

(Presented at a meeting of the New York Local Section of the Institute, Apr. 12, 1912.) I. INTRODUCTION. THE problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific stand-point, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by way of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " ?flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of combustion as they occur in ordinary flames. All hot surfaces have an accelerating influence upon chemical changes in gaseous systems. If, at any temperature, a gaseous system, A, tends to pass over into another system, B, contact with a solid at the same temperature will accelerate the process. To take a very simple example, if a mixture of hydrogen and oxygen in their combining proportions (electrolytic gas) were maintained in an inclosure with smooth glass walls at a temperature of, say, 450° C., there would certainly be a tendency to form steam, but the rate of change would be negligibly small. If, however, there were brought into the system some porous solid material at the same temperature, so that a large surface was exposed to the gases, the rate of change would at once be rapidly accelerated in the layer of gas immediately in contact with the hot surface. Steam, the product, would diffuse outward from the surface, and the supplies of hydrogen and oxygen at the surface would be renewed by diffusion inward. Thus combustion would proceed heterogene-

Sep 1, 1912

By W. B. Plank

I HAVE been asked by the Chairman of the Engineering Education Committee to outline what the engineering colleges would like the mining companies to do with the young engineer just, out of college. It has been suggested that, because my own personal experience has been almost entirely within the coal industry, I handle this subject from that view- point. Many thoughtful engineering educators are today wondering what effect the present employment policies of many industrial companies are going to have on the young man just starting out in his profession. Since before the World War large industrial concerns, such as those in the electrical and mechanical industries, have gone to the colleges to interview 'likely graduates until today there has developed in most of our engineering colleges, especially in the eastern part of the country, what appears to be a lively competition on the part of these companies in bidding for the young graduate engineer. The employers of mining engineers, with one or two exceptions, have not yet begun to enter this competition. It remains to be seen how serious this situation will become, how it will affect the training of other engineers, and what effect, if any, it will have on the mind of the young man about to enter college who may be inclined to take up mining engineering, but who gains the impression from this well advertised employment service just mentioned that there is no opportunity for him in the mineral industry as com- pared with the opportunities offered in say civil, mechanical, and electrical engineering.

Jan 1, 1929

By Games Slayter

NO reasonably well-informed person believes that the role of minerals, both metallic and nonmetallic, will be any less important in the future than it has been in the past. The contrary is true. Industrialization is based on mineral resources and man's ability to make use of them. A nation's standard of living, its political and military power, will continue to depend largely upon the extent to which it is industrialized-and minerals are the raw materials both of the machine and the power to run the machine. Minerals are also the raw materials of human health and stamina. The world's healthiest, most vigorous, and most long-lived peoples have always been those that have lived in regions of the globe where the earth is rich, and kept rich, in the phosphates and other minerals required for the production of the so-called growth foods. Only a small proportion of the land surface of the globe is suitable under any circumstances for large-scale production of these and other essential foods. As things stand, only a part of this land is capable of such production either because the soil minerals have been exhausted by cultivation, or because they never existed in the soil in sufficient quantities.

Jan 1, 1943

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment The operations in Cuba have already been described by F S Norcross, Jr 7 and the laboratory study of manganese oxide flotation goes back a number of years 4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill The writers have had access to Company records and in particular to the petrographic studies made on thin sections of ore by the late Professors R J Colony and Philip Krieger, of Columbia University They acknowledge their debt to both of these men for the help derived from the reports Manganese oxides are black, friable, smudging It is therefore, very difficult to judge operations by inspection The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper, namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganifeous mineral crystals with impurities of various sorts By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane " The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all However, it seems to be the best under the circumstances This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By F. J. Plecity, W. C. Leslie, F. W. Aul

During isothermal recrystallization, the rate of grain growth in dilute Fe-hlo alloys decreased rapidly with increasing Mo content, up to -0.04 at pct, and less rapidly therea-fter. Rate of growth also decreased sharply with time at constant temperature. The observed rates of boundary migration did not cor,espond to predictions of the Lucke-Detert theory. It is proposed that the growth of recrystallized grains is inhibited by clustering of solute atoms at inzperfections in the unrecrystallized matrix. It is now firmly etablished" that the rate of re-crystallization of cold-worked metals, i.e., the rate of growth of recrystallized grains into the deformed matrix, is greatly inhibited by the presence of alloying elements in solid solution. The effect is greatest with the first very small quantity of alloying elements, and additional increments cause much less pronounced retardation of growth. The early papers on this subject were reviewed in Ref. 6. The mechanism of retardation of growth is not clear; only one theory, due to Lucke and Detert? has been advanced. This assumes an elastic interaction between grain boundaries and solute atoms which tends to increase the concentration of the latter in the grain boundaries. Except at very low solute concentrations or at high temperatures, the mobility of the boundary is assumed to be controlled by the rate of diffusion of the accompanying solute atoms. Abrahamson and Blakeney2 have noted a correlation between "recrystallization temperature of binary alloys of iron and the number of d-shell electrons in the solute atoms. There is need for considerably more experimental data on the effect of solute elements on the rate of migration of grain boundaries into the deformed matrix, to provide the basis for an understanding of the annealing process in metallic solid solutions. Only a start has been made in this direction. To avoid unnecessary complications, alloys in which precipitation does not occur should be used, but to produce the maximum effects it is desirable to select alloys with a large difference between the sizes of the atoms of the solvent and solute. For these reasons, alloys of iron and molybdenum sen for this study. MATERIALS AND PROCEDURES A 30-lb. ingot of iron and four similar ingots of Fe-Mo alloys were vacuum melted in magnesia crucibles and poured into cast-iron molds. The molybdenum contents were planned according to the results of Abrahamson and Blakeney2 sothattwoalloyswould fall in the region of rapid change of recrystallization kinetics with change in composition (0.006 to 0.015 and 0.030 to 0.045 at. pct Mo) and two alloys would fall in the region of gradual change (0.18 to 0.24 and

Jan 1, 1962

By Gerald Sherman

(San Francisco Meeting, September, 1915) THE ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be-discussed here in detail. Certain of their characteristics, however, control -methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattered through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most general characteristics are the softness of the ore and their great horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been .subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread . over a great area. A diagram map (Fig. 1), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 9, 1915

By Stephen Taber

A vein may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-bearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-books today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped masses should be classed as veins or as dikes. Some of the earlier investigators have also advocated the theory that veins are contemporaneous in origin with the inclosing rock, while others have believed the vein minerals to represent a recrystallization or transforma-

Jan 1, 1920

By Alexander L. Field

IN a previous paper,' the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of " red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the rettetion between zirconium and sulfur in molten steel may be represented by the simple equation, Zr + 25 = ZrS², and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion. Hot-rolling Properties of High-sulfur Steels with and without Zirconium The chemical composition of twenty-eight steel ingots embracing eleven heats made in a basic-lined electric furnace is shown in Table 1. The practice followed in the manufacture of these high-sulfur steels was described in the previous paper. Table 1 also gives the behavior of the

Jan 1, 1924