Search Documents

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By Russell G. Wayland

SINCE the installation at Kropfmuehl, Bavaria, of a modern flotation concentrator in 1938, the flake and fine graphite from the Passau area can now be delivered in about any normal specified carbon content of any size range up to a flake averaging about 0.7 mm. The graphite finds a wide German and export market for crucible manufacture, pencil leads, dry cells and other uses.

Jan 2, 1951

By S. Ramachandran, L. A. Vazquez, N. L. Grauerholz

A novel process is described for the selective flotation of scheelite from low-grade (- 0.5% W03) tungsten ores having appreciable quantities of calcareous and siliceous gangue minerals. Specifically developed for the Tempiute, Nevada facility of Union Carbide, the process yields tungsten concentrates exceeding 15 percent W03 with at least 85 percent recovery. This condition was not achieved through conventional processes. This process consists of conditioning the ore pulp with judicious amounts of lime, followed by soda ash and sodium silicate as modifiers. The scheelite is then floated using a mixture of oleic and naphthenic acids as collector. Contrary to the common observation as to the deleterious effects of calcium in fatty acid flotation systems, lime addition is found to be beneficial in achieving satisfactory results. The process has also shown excellent results on a Brazilian scheelite ore.

Jan 1, 1976

By Laszlo Valentyik, John T. Patton

A conventional heavy-media separation process utilizes a mixture of finely ground solids like magnetite, ferrosilicon, or shale and water. The always-present clay in the medium acts as a stabilizing agent since the coarse heavy-media solids would quickly sink if they were mixed only in water. As the pseudoplastic nature of polymer solutions has excellent suspending properties, laboratory investigations were conducted at the Institute of Mineral Research on whether polymers could be used as suspending agents for finely ground heavy media. The preliminary results (published previously) of the laboratory research studies have shown that sufficient stabilities of heavy media can be obtained at a relatively low polymer concentration. This paper is a continuation of the previous work and it presents some of the results of recent studies where the rheological properties of the heavy-media suspensions were studied in a newly developed settling tube and the already familiar concentric-cylinder-type consistometer. In the investigations bentonites as a stabilizing agent also were included so that comparative results would be available to the plant engineer to assist him in the choice of the most suitable material for stabilizing various heavy media.

Jan 1, 1977

Jan 1, 1894

By J. Kostuik, M. J. de Bastiani

Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10° to 45° on the north limb and 10° to 20° on the south limb.

Jan 12, 1960

By R. G. Treuting, W. C. Ellis

D. Whitwham, M. Mouflard, and P. Lacombe (British Council Research Fellow, Labratoire du Professor Chaudron, Vitry-sur-Seine; Inqenieur de Recherches, Labratoire de Vitry; and Maitre de Recherches, Labratoire de Vitry, Professeur Adjoint de Metallurgie, Ecole des Mines, Paris)—The authors' work is of great interest in bringing out the geometrical relations existing between twinned lattices, and for the notion of a coincidence super lattice developed from this. We should like to point out that a similar idea was put forward by Friedel8 in his book on the subject of lattice merohedrism "merihedrie réticulaire:"—When two crystals A and B are twinned with respect to a mirror plane, there exists a common superlattice, "réseau periode," which is independent of the contact surface between the two crystals. The volume V of this superlattice is a simple multiple of the volume v of the lattice of crystals A, or B, (Fig. 5). This "multiple cell" is defined by the twin plane (p q r) and a row of atoms [h k l] normal to this plane, the base being taken as the smallest unit (two-dimensional) of this plane. Two cases must be considered. First when the multiple cell, as defined, has no atom site at its center nor at the center of its faces other than (p q r), v the twinning index is defined by —. In the second v case, when one of the two above conditions does not v apply, then the twinning index is V 2v A more intuitive definition of the twinning index would be the proportion of atoms of C, which would coincide with those of C1 when the C, lattice is imagined to extend on the other side of the contact surface. In the case of cubic crystals, the twinning index

Jan 1, 1952

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By Stanley B. Roboff

Throughout the world nuclear power re- actors are being designed and constructed as the energy source for stationary power plants. They are built to power submarines, surface ships, and long-range aircraft and to provide small package power plants that can be set up with relative ease in outlying areas. Regardless of type, most of these plants are designed to operate at the highest permissible temperatures and with the greatest possible burn-up of fuel. On paper it is now possible to design a nuclear power plant that will out-perform all existing types of power-generating plants, and at costs which are attractive. Such plants, however, are not now being built, nor will they ever be built, unless major engineering advances are made in the realm of reactor materials. The reason for this is straight- forward enough. Although it is known that huge quantities of energy can be generated in nuclear fuels within short periods of time, as yet there are no construction materials capable of withstanding the severe conditions that would exist within a power reactor operating with ultrahigh output.

Sep 1, 1956

WHEN Georgius Agricola, in 155o, dedicated his now famous De re Metallica to the rulers of Saxony, Thuringia, Meissen, and other, smaller principalities, he included in his review of previous works on similar subjects reference to two books written in German: one, an "anonymous, rather disorganized account of assaying for metallic content and of metals," which must be the Probierbüchlein, the other, "dealing - with veins, written by Calbus of Freiberg, a well-known physician."* Calbus is mentioned a second time-and cited-at the end of the Third Book of De re Metallica. Comparison of the citation with the Bergbüchlein leaves no doubt that Agricola considered Calbus of Freiberg the author of the latter work, although all the editions of the Bergbüchlein known now were published anonymously. It is generally accepted by those who have dealt with the bibliography of the Bergbüchleint that Calbus was Ulrich Rülein von Kalbe, who served the City of Freiberg, in Meissen, as health officer in 1497, as member of the City Council in 1509, and as mayor in 1514 and 1519. He died at Leipzig in 1523. In connection with the very garbled description of the mining compass toward the end of Chapter 3 of the Bergbüchlein it is of interest that von Kalbe is supposed to have been not only a physician of repute but a mathematician, astronomer, mine sur-

Jan 1, 1949

By J. N. Sicking, F. H. Brinkman

A new method for obtaining equilibrium vaporization ratios (K-values) for reservoir fluids has been developed and tested. By application of the method, complex experimental measurements of liquid and vapor phase compositions are eliminated. This simplified technique reduces the cost of experimental equilibrium-ratio data for reservoir studies of condensates and volatile crude-oil systems. The method is designed for systems of constant composition and, therefore, is best suited for depletion studies where compositional changes at high pressures are minor. The basic data required, in addition to the composition of the initial reservoir fluid, are the relative vapor-liquid volumes and densities at reservoir temperature and variom reservoir pressures. Tests demonstrated that the method predicts equilibrium ratios accurately for condensates. A single test on a crude oil was not conclusive; further testing will be necessary before the accuracy of the method can be determined for crude-oil systems. In addition to determining equilibrium ratios, the calculation method provides information on the physical properties of the "plus" component in the vapor and liquid phases. The "plus" component is that mixture of components heavier than the least volatile fraction analyzed. This information is useful in studies of both natural depletion and cycling operations for condensate reservoirs where the heptanes-plus component in the gas phase is produced from the reservoir. INTRODUCTION As more volatile oil and condensate reservoirs are found, the use of phase behavior techniques to predict their performance is increasing in importance. These techniques have long been used for condensate fields and have more recently been applied to crude-oil fields containing oils of medium-to-high volatility. In these phase behavior methods, equilibrium ratios (K-values) are used to predict compositional changes in the reservoir fluids—thereby accounting for the recoverable oil that exists in the gas phase. The reliability of the predictions depends to a large extent on the equilibrium ratios used. These values must be obtained for each component for the entire pressure range being investigated. Unfortunately, because of the complex nature of hydrocarbon mixtures, accurate K-values are hard to obtain. The equilibrium ratios for a particular component will vary not only with the temperature and pressure, but also with over-all composition of the system. The importance of composition is quite critical at elevated pressures, but becomes negligible at pressures below about 300 psia. Therefore, because most phase behavior problems involve the high-pressure region, each fluid system becomes a special case. Experimental programs to determine characteristic K-values are quite difficult and time-consuming. Thus, it is often necessary to resort to approximations of the K-value data. Charts giving K-values for various mixtures and classes of mixtures are available in the literature. However, there are two major difficulties in using them: (1) the K-values of the "plus" component (that mixture of components heavier than the last one analyzed) must be obtained by extrapolation from the K-values of the other components; and (2) the K-values obtained must finally be adjusted by trial and error to agree with observed volumetric data. To eliminate these difficulties, a new method of determining equilibrium ratios was developed. Briefly, after the composition of the system as a whole has been analyzed, the method uses empirical correlations and the gross fluid properties of the system (relative vapor-liquid volumes and densities) to calculate K-values. Because the calculative procedure is long, it is best solved on a digital computer. About one hour of machine time on an IBM 650 computer is required to develop a K-chart for the fluid being examined. DEVELOPMENT OF THE METHOD OF OBTAINING K-VALUES Equilibrium ratios are defined as the ratio of the mole fraction of a component in the vapor phase to its mole fraction in the liquid phase. This statement is expressed in Eq. 1. A typical plot of equilibrium ratios for a particular system is shown in Fig. 1. It should be noted that, at pressures near the saturation pressure, the K-values appear to converge to a common point. This apparent convergence point is called the convergence pressure and is a characteristic of the system involved. Various empirical correlations of K-values have been noted. It has been observed that an isothermal plot of

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By A. F. Taggart

THE following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laboratory at the Columbia School of Mines during the years 1926 to 1928-inclusive. CLASSIFICATION OF EXPERIMENTAL WORK The experiments performed may be grouped for purposes of description under the following general -headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils) c. Action of dissolved collecting agents. II. Frothing agents. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. SUMMARY OF THE ORIGINS OF PRESENT-DAY FLOTATION PRACTICE The first practicable, foolproof method of froth flotation was described in U. S. patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.1 The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when' compared with those used today.

Jan 1, 1929

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By Euzebio P. de Oliveira

One of a recent batch of samplcs from the Serra da Baliza, in the state of Paraná, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto Uniáo to Uruguay discovered asphalt coming from eruptives that outcrop along the Rio de Peixe. The occurrence of asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botucatd sandstone is always a hard vitrified rock, from the metamorphic action of the overflowing eruptive contacts. In this region, howeyer, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used in mortar for building in Guara-puava and Palmas. South and west from Porto Uniáo, this bench of sandstone is about 50 m. thick, and is capped by a heavy bed of basic eruptives, many of which are amygdaloids. Nature of Rocks Dr. Geo. P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking." Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination of many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety of structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 1, 1921

Jan 1, 1894

By S. F. Emmons

Introductoy.—In view of the fact that an opportunity is to be offered to the members of the Institute present to inspect the recent developments of gold-deposits in the immediate vicinity of Washington it has seemed appropriate that some preliminary description of them should be given which may facilitate that inspection. It would have been a matter of much satisfaction to me to be able to present some general description of the gold-deposits of the Appalachian system ; but I have as yet had no opportunity of personally examining any others than those of Montgomery county, and these are still in their infancy. It is, moreover, a slower and more difficult operation to make geological observations in this region than in the more northern States; for whereas in the latter region the

Jan 1, 1890

By Wilfred P. Sykes

AT intervals in the course of history an event occurs which, though scarcely heeded at the moment, marks in retrospect the beginning of a new era in some one field of human activity. Such a happening is perhaps more readily spotted in the field of technology than in other realms of human endeavor. Here the span of years is relatively short and the records have been kept with some degree of precision. In the current scene of our social and economic drama the art and science of metallurgy is playing a major role. Off stage will be found the metallurgist in one guise or another aiding, he trusts, in the development of processes and products which will contribute to the happiness of his fellow men. The results of his efforts appear in the form of metallic substances known as alloys built up from any two or more of the wide variety of metals which have been extracted from the mineral deposits in the earth's crust. An alloy by virtue of its inherent physical properties may seem ideally suited for human use in a special way but until this material can be produced economically it will fail to attain a place of prominence as an article of commerce. In fact many commercial alloys are being continually replaced by new or modified compositions better suited to meet the increasingly severe demands of industrial service.

Jan 1, 1939

By E. A. Holbrook

IT may be taken for granted that a mine official knows his duties, as outlined by the bituminous mining laws of the State, he knows how coal should be mined and transported, and he has judgment on any possibly unsafe condition in his mine. Certainly, if he is weak on any of these points, there are definite ways in which he can acquire the needed knowledge. If with this knowledge the mine official has the necessary practical experience to bring self-confidence, he stands before the world as a man who knows his job. There is, however, another side to his work, one not found in hooks, a side even that may not be learned at the face even though one spends a lifetime there. The actual duties a mine official knows and performs are the tangible and definite things about his work. There are other things which may be termed intangible, because they are hard to pin down and see, and. which appear to be of equal importance in successfully handling a job and which in time determine the very success of the company itself.

Jan 1, 1930