Search Documents

By O. P. Hood, G. St. J. Perott, S. P. Kinney

"FOREWORD (By O. P. Hood, Chief mechanical engineer).During the war certain suggestions concerning power production were made by Mr. Walter E. Trent to the War Inventions Board, and at the request of the War Department facilities for experimental work were provided on the grounds of the. Bureau of Standards.The experiments were along the line of controlling the conditions of combustion in a closed space. In order to reduce slag troubles, experiments were carried out for removing ash from powdered coal. After the war, work along this line was continued, resulting in the Trent Process, which agitates or beats together powdered coal, water and oil.A new technology had previously been given to ore preparation by the use of small quantities of oil in water with froth flotation, and although the methods, results and mixtures of the Trent Process were quite different, yet the same physical phenomena of differential wetting used, and the possibility of there being interesting results in fuel technologic was evident. A cooperative agreement was entered into, whereby the Bureau of Mines was to investigate the underlying physical and chemical facts and make them public, and the Trent Corporation was to pay the cost of the investigation.The several reports as made have been available to any one interested, and are now to be published. While the Bureau of Mines felt justified in investigating the physical phenomena so far as might be done in a laboratory, and so far as public interest might reach, no attempt was made to discover the commercial possibilities which development might bring. The question of commercial possibilities must be left for commercial enterprise to answer."

Jul 1, 1921

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By Steven A. Fechner

In 1991 and 1992, the Bureau of Mines completed chromium, platinum-group metals (PGM), and tin investigations, and started indium, manganese, titanium, and vanadium investigations in Alaska. These studies were done as part of the Site Specific Minerals Investigations project. As a result of this work, the Bureau found PGM-bearing composite plutons in the Yentna River area of the Alaska Range, which are chemically similar to composite plutons in other parts of the Alaska Range and to Ural-Alaskan type complexes. Previously unknown chromium and PGM occurrences were found in the western Brooks Range. A compilation report on the Bureau's chromium and PGM investigations in the western Brooks Range was also published. Indium was found in anomalous concentrations at the Lost River tin deposit. Small occurrences of manganese were located, mapped, and sampled in the Wiseman and Chandalar quadrangles, and in the Liberty Falls, Prince William Sound, and Homer areas. Tin occurrences in western Alaska were summarized in three Bureau open file reports. The beaches near Cape Yakataga and Yakutat were evaluated for their titanium potential and a sampling methodology was developed. Vanadium investigations included examining streams in the Wiseman and Eagle areas that contained anomalous vanadium values. In the Eagle area, high vanadium, uranium, and copper values were found in the basal layers of the Road River formation.

Jan 1, 1994

By Paul M. Tyler

THE winning of metals from Nature has been advanced to a degree of efficiency that commands admiration even in this Machine Age. Economy of human effort underground, in surface plants, and in treatment works, and better means of performing all manner of operations have cut costs and im¬proved products to an extent that seems far beyond the wildest imagin¬ings of those that labored in the days of hand mining and muscular metallurgy. Principles and methods borrowed from other professions and sciences - mechanical engineering, chemistry, and physics-all have con¬tributed to the rapid development of ore production and treatment, but no small part of the achievements must be credited to the free exchange of ideas within the industry itself and mass attack upon problems of mutual concern. The esprit de corps or class consciousness that has contributed so effectively to the progress of the metal industries has been less apparent among nonmetallic mineral producers. As a class they have been handicapped by inadequate contact with the metal-mining fraternity as well as among themselves.

Jan 1, 1935

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By Brunno Spinelli Pimentel

Ambientes contendo H2S e CO2 impõem condições severas a componentes fabricados em aços, já que estes podem sofrer corrosão com perda de propriedades mecânicas e falha das instalações. Uma preocupação é a quantificação dos fenômenos envolvendo difusão do hidrogênio atômico, o qual (seja pelo gás H2 em interfaces ou pela interação com ligações atômicas ou discordâncias) pode causar redução nas energias superficiais de fraturamento prejudicando ductilidade e tenacidade. Neste cenário, este trabalho investiga a fragilização por hidrogênio em um aço microligado API 5L X65 sour obtido de um tubo de diâmetro externo 32” e espessura de parede 20,6 mm fabricado pelo processo UOE. Amostras longitudinais e transversais de tração (ASTM E8/E8M) foram extraídas e imersas em solução saturada com H2S. O eletrólito empregado foi a solução A (ácido acético contendo cloreto de sódio) da norma NACE TM0284-2011, fazendo-se purga com N2 e injeções de H2S. Os tempos de imersão foram de 0, 96 e 360 horas, sendo os ensaios de tração realizados após doze dias do término da imersão. Os resultados não revelaram efeito estatisticamente relevante na resistência mecânica, na evolução tensão-deformação e tampouco no módulo de tenacidade. Entretanto, foi observado maior espalhamento dos resultados advindos de amostras submetidas a H2S. Esse comportamento sugere que o hidrogênio influenciou no micromecanismo local de fraturamento, mas com inexpressivo comprometimento das propriedades monotônicas macroscópicas. Tal desempenho pode ser fruto da microestrutura com grãos refinados e do baixo nível de inclusões encontrado, indicando poucos e uniformes sítios de ancoramento de hidrogênio irreversível.

Aug 8, 2018

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938