Search Documents

By ROBERT R. RICHARDS

My. first paper, read at the Cobalt Meeting of the Institute,1 July, 1907, dealt with the behavior of a small Wilfley table when concentrating galena from quartz, the table being fed with natural products, with sized products; and with classified products. Since galena, having a specific gravity of 7.5, is among the heaviest minerals ordinarily concentrated by Wilfley table, it was desirable that a similar set of tests upon a mineral of, lighter weight should be made. Chalcopyrite, of a specific gravity of 4, would have been the best mineral for this purpose, on account of its great importance as an economic mineral, but in carrying out the test, however, I was obliged to content myself with a cupriferous pyrite, the specific gravity of which was 4.68 and the contents in copper 8.80 per cent. Through the kindness of Mr. H. 0. Cummins, this material was obtained from Shasta, Cal.,in very pure, clean, homogeneous condition. It was broken by rolls to 2 mm. in size, taking care to make a minimum of slimes. The quartz used to mix with it was pure, white, New England quartz, broken in the same way to the same size. In studying the accompanying tables, it should be borne in mind that the material concentrated was of low copper-content, and in many cases the quantity fed to the machine was 1 kg: or less.. As a consequence of the smallness of the 'quantity treated it was very difficult to adjust the table and get it in condition to do its best work before the feed became exhausted, and for this reason many results were obtained which appear irregular.

Sep 1, 1908

ABSTRACTMechanised cut and fill stoping in the Racecourse orebodies between II and 9 levels was started in 1964.Five stopes are in progress over the two level interval, extracting the full strike length (600-2,000 ft) of each orebody without transverse pillars.Each stope is served by a central 10 ft by 12 ft service intake ventilation raise and an 8 ft by 8 ft return air raise at each end of the stope. Each stope is divided into two sections for drilling. firing. mucking, and fillingto maintain steady production. All equipment is kept in the stope for one level lift stoping. Gardner-Denver 2 boom jumbos are used for uphole drilling and Wagner ST 5 Scooptrams for loading and transport to ore passes located in the footwall of the orebody. A Wagner PTIO is used for materials handling and scaling of the stope backs.Mill tailings, after one stage of cycloning are used to fill the stope, one section at a time. About 80 per cent of the water is removed by decantation while the remainder percolates through hessian-covered pipes and boxes.The ore is passed to 11 level where it is hauled by the 3 ft 6 in. gauge train to the tipple at the shaft area. The ore is crushed underground before hoisting to the surface.A performance of about 100 ton/manshift is achieved by the drilling, blasting, and mucking crews in the stopes.

Jan 1, 1968

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By S. V. Burr

"A 28-year study of cross folds leads to the conclusion that the northwest-southeast folds recognized in many areas of North America are part of a regional pattern. Detailed examination of over 650 geological maps and reports of Ontario indicates that this folding can be traced across the province. Evidence is presented that this fold pattern played an important part in determining the pattern and scale of intrusion, that its recognition in the field can aid in defining stratigraphy, folding and faulting, and that it may have played an important role in channeling hydrothermal or magmatic mineralization. IntroductionThe concept of regional cross folding in Ontario is not new. W.H. Gross (1955) discussed regional cross folds in the Archean of Northwestern Ontario, and A.M. Goodwin (1961) referred to regional cross folds in the Archean of Ontario and Quebec. However, the interpretation in this paper is new.The writer saw a cross fold for the first time, underground, at Little Long Lac Gold Mines in Geraldton, Ontario, in 1951. This recalled the ""transverse folds"" on E.R. Faribault's classical maps of Nova Scotia, published by the Geological Survey around the turn of the century; M.E. Hurst's cross fold(s) at Timmins, Ontario (Figure I); and the cross folds mapped by A.W. Jolliffe in the Yellowknife area of the Northwest Territories. All these mapped cross folds had one thing in common with the fold at Little Long Lac: A northwest-southeast axial trend. Were such cross folds of purely local extent, or might they be indicative of a widespread regional fold pattern? If so, has such folding any significance for mineral exploration or potential?By 1959, based on a study of about 1000 Canadian geological maps and reports, including 291 in Ontario, the writer reached the conclusion that cross folding trending northwest-southeast is so widespread as to constitute a pattern of folding, and that such cross folding should produce changes in plunge along pre-existing greenstone fold belts."

Jan 1, 1980

By W G. Forbes

SOME 20 years ago, upon finishing second year at the University of Manitoba, I was faced with the choice of whether I wanted to be a geologist or a chemist. Accordingly, I sought out Professor Brownell, Head of the Department of Geology, to ask him what a geologist did. His reply contained the statement that following graduation one went out into the field in northern Canada for 5 to 15 years to reduce to practice what had been learned at university. To a young man, very socially conscious, even one year, let alone 5 to 10, in a small mining community sounded like being banished to a monastery in the Himalayas and thus I turned to chemistry. Moving to the present, last month I asked a geologist, and then a mining engineer, what does the fresh graduate in their field do these days? The reply was: usually serve an apprenticeship for an indeterminate period either underground or in the field learning the job.

Jan 1, 1965

By H. A. Doerner

"The pure mineral chromite, FeO.Cr203, consists of ferrous and chromic oxides, chemically united in equal molecular proportions. Unfortunately, pure chromite as defined above appears to be a rare exception. In most chrome ores the mineral may be considered a combination of spinel, MgO.Al203, and chromite, with the latter predominating. The ratios between the four common constituents Fe0, Mg0, Cr203 and A203 vary greatly, and other minor constituents such as TiO2 and. Fe203 may also be present.In the mechanical concentration of chromite ores the maximum grade of concentrates that can be produced is thus limited by the composition of the chrome minerals present. Pure chromite contains 68 per cent Cr203, but the Cr203 content of the chrome minerals in commercial ores varies between 45 and 60 per cent and the average is not far from 55 per cent.Chromite is usually associated with serpentine. Other silicates, quartz, dolomite, magnetite, ilmenite and other iron Minerals are frequently present.The amenability of a chrome ore to concentration, depends upon the kind and amount of the various gangue minerals present and the amount .of crushing necessary to separate the chromite from them.A relatively small amount of chrome ore is concentrated by milling. In most cases the mine product is simply hand-sorted. Such chrome deposits as are known in the United. States can not be worked in this way on account of one or both of the following conditions: High cost of labor and finely disseminated impurities. There are, however, several deposits in the United States, Canada, and Alaska which may be able to compete with imported or by efficiently utilizing modern ore-dressing and milling methods."

Nov 1, 1930

By G. B. Quaye

The deep level gold mining environment is characterized by high stresses that give rise to intense mining induced fracturing of the rock mass surrounding the stopes. In a geologically disturbed region where the intensity of mining induced stress fracturing is high, the degree of faulting and/or the frequency of other geological features such as joints may pose serious strata control problems. Unfavourable intersection of these discontinuities namely, faults, joints and mining induced stress fractures tend to divide the immediate hangingwall into unstable keyblocks which, if not supported, may result in extensive falls of ground. Effective support strategies therefore demand detailed investigation of the predominant inclinations and orientations of these discontinuities. The orientations and inclinations of these discontinuities surrounding a deep level stope have been measured. The results are projected onto the lower hemisphere of a stereographic net to determine the factors that contribute to the falls of ground in the stope. The analyses reveal that unfavourable intersection of these discontinuities divides the immediate hangingwall into unstable wedges that may become dislodged between support units.

Jan 1, 1998

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By L. van Dyk

The project was aimed at evaluating the double-header trains implemented at Great Noligwa mine, looking at the changes from the old conventional trains to the new trains, and identifying possible improvements to obtain an even better and more productive tramming system. The methods used to evaluate the double-header trains at the mine included personal observations, time studies, personal interviews, technical research, safety analysis, cost analysis, production analysis, breakdown analysis, break test analysis, comparisons and working closely with engineering department and manufacturers. Issues that were evaluated are the improvements in safety, cost reductions, tramming congestion reductions, better efficiencies, labour optimization, enhanced driver safety and maintenance. Shortcomings of the double-header trains were identified and recommendations made to improve on the shortcomings. Findings of the evaluation study indicated the following: ?Drastic improvement on safety ?Extreme cost reductions ?Reduction in tramming congestions and bottlenecks ?Better tramming efficiencies ?Optimized labour placement ?Enhanced driver safety ?More effective maintenance. Although there is room for improvements, the double-header trains were implemented with great success at Great Noligwa mine. It is currently the preferred tramming methodology at Great Noligwa mine, and is also implemented at other Anglo Gold Ashanti?South Africa shafts. This tramming system has huge potential for growth, not only in Anglo Gold Ashanti, but in all other older mines that experience major tramming problems.

Jan 1, 2008

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By R. Benito

This paper describes the application of modern data-analysis tools, such as data mining, to determine a representative cost driver for haulage activity. This cost driver was subsequently used to trace incurred haul costs by bench for openpit optimization. For this purpose, large amount of previously unused cost and production data from an open pit mine was extracted, loaded, transformed and integrated into a data warehouse. Predictive modeling was performed using Microsoft Decision Trees algorithm to compute expected unit haul costs by bench for future mine expansions. Finally, a sensitivity analysis was carried out to determine the effect of two cost drivers (if any) for incremental haul costs in the final pit outline process.

Jan 1, 2008

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007