Search Documents

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120') below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300') above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820') of horizontal tun-nel, averaging 3.6 m x 3.6 m (12' × 12'), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13') long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10') diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

During recent years there has been a marked increase in the use of explosives in Queensland coal mines. Delay detonators have been introduced and their use has extended with the wider application of mechanised methods of mining.The need for careful study of the characteristics of delay detonators is stressed so that the advantages of simultaneous firing, from the points of view of safety and efficiency, may be obtained. With their use new potential hazards are introduced. These hazardsare considered and means whereby the overall safety may be improved are discussed.The increase in the number of misfires since the introduction of delay detonators is shown and the examination of misfired detonators is described. Lessons to be learned! from these misfires are noted and details are given of the essential requirements for safe and efficient blasting using delay detonators.INTRonUCTIONOne of the aims of mechanization in coal mines is to reduce the physical effort applied to the winning of coal. Explosives play an important part in achieving this and, following the introduction of power borers for the drilling of shot-holes in Queensland coal mines, much of the arduous work associated with coal getting has been eased. During recent years there has been a marked increase in the consumption of explosives, as shown in Table 1, and it must be the aim of all to use these explosives safely and efficiently. That there are dangers associated with the use Of explosives cannot be denied. The shotfiring operation is fully covered by legislation and, being under the control of one man, shQuld be capable of being carried out with a high degree of safety. The main source of accident appears to be the failure to take proper cover and this has resulted in...

Jan 1, 1958

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By Rob Thomas

Pre-driven recovery roads are used to speed up the longwall recovery process by reducing bolt-up requirements and by improving ground conditions on the face during the removal of the powered supports. To lower the geotechnical risks associated with the use of pre-driven recovery roads, and so improve its overall acceptance in the industry as a viable alternative to more conventional, potentially difficult and costly longwall recoveries, this paper outlines (i) a geomechanical model for the use and design of pre-driven recovery roads, (ii) an updated version of the worldwide database on pre-driven recovery roads, (iii) a summary of the various methods of holing a longwall into a pre-driven recovery road and (iv) a series of relevant ground support and strata management guidelines.

Jan 1, 2008

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By H. Sarvamangala

Biomineralization of manganese on titanium condenser material exposed to seawater has been illustrated. Biom-ineralization occurs when the fouling components, namely, the microbes, are able to oxidize minerals present in water and deposit them as insoluble oxides on biofilm surfaces. Extensive biofilm characterization studies showed that an alarmingly large number of bacteria in these biofilms are capable of oxidizing manganese and are, thereby, capable of causing biomineralization on the condenser material exposed to seawater. This paper addresses studies on understanding the exact role of the microbes in bringing about oxidation of manganese. The kinetics of manganese oxidation by marine Gram-positive manganese oxidizing bacterium Bacillus spp. that was isolated from the titanium surface was studied in detail. Manganese oxidation in the presence of Bacil-lus cells, by cell free extract (CFE) and heat-treated cell free extract was also studied. The study confirmed that bacteria mediate manganese oxidation and lead to the formation of biogenic oxides of MnO2, eventually leading to biomineralization on titanium surface exposed to seawater.

Jan 1, 2008

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By J P. Ashby

Compared with elsewhere in the world, New Zealand quarries have tended to be mostly small. The reasons for this are a combination of the relatively high transport costs, low population density and a pioneering, self-employed attitude. The small size of the operations is reflected in low productivity, a tendency to repair and rebuild equipment rather than replace it, designed flexibility in the processing plant, minimal reserves investigation or development planning and a versatile and innovative work force who are generally not professionally trained. The Resource Management Act and the Health, Safety and Employment Act as well as a customer driven demand for higher quality and consistent products will have even greater influence upon future direction of the Industry. The trend will be towards fewer quarries operated by companies and professional managers that can adapt to the new demands.

Jan 1, 1993

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996

By Dean Workman

Long extensible conveyor systems are an important option for efficient tunnel excavation where intermediate access is impractical. The conveyor system designed for the Pula Subbaiah Veligonda Tunnel #2 in Andhra Pradesh, India will eventually extend to 19.35km. The Ø10.0m water diversion tunnel will be excavated under India?s largest tiger sanctuary using a Robbins Double Shield TBM. Once extended, the conveyor will be one of the longest single-flight systems ever installed in India, and is expected to offer increased system availability over comparable systems using muck cars. This paper will examine the engineering challenges of long-flight extensible conveyor systems in the areas of belt selection, component design, and equipment location in confined assembly and launch areas

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

Jan 1, 1987

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By T. Geyer

The Carbon Disclosure Project (the pre-eminent global initiative for institutional investor collaboration on climate change) groups the business risks (and opportunities) related to climate change into four categories: 1. Regulatory risks from tightening legislation (and opportunities for companies that can make the carbon market work for them), e.g. rising costs for carbon and energy-intensive processes. 2. Competitive risks & opportunities generated by a possible decline in customer demand for carbon/energy intensive products (and opportunities from a consequent rise in demand for efficient / low carbon products). 3. Reputational risks from perceived inaction on climate change (and benefits to those perceived to be ?solutions providers?). 4. Physical risks from changes to climatic patterns, e.g. asset damage from extreme weather events; project delays; water scarcity; resource risks as certain crops become no longer viable in certain areas and new supply chains become necessary; and potential human and socio-political impacts. All of these are already having repercussions for businesses in certain sectors and geographies. The understanding of specific impacts of climate change is still evolving but it is clear that climate change will have a material impact on the value of many businesses, either directly or indirectly. Many commentators and analysts consider that rising energy costs are likely to represent the most direct and immediate investment risk that climate change and the resulting regulatory responses will create for business in the near term. However, it is already possible to identify numerous examples of competitive and reputational risks and opportunities that are leading to significant value creation or destruction in business: the success of the Toyota Prius; the rush by the UK?s leading supermarket retailers to ?green? their brands; and the surging fortunes of companies involved in the manufacture of renewable energy generation equipment, are all manifestations of this trend. In addition, the potential physical impacts of climate change are also making themselves felt in certain sectors: an example is the Australian wine industry, suffering after an extreme and prolonged period of drought. THE PROJECT This paper describes a project undertaken for a multinational mining company to examine the physical risks from climate change across its international business operations. The study addressed 163 components of the business and included operating sites (mines, smelters, and refineries), key transport routes (road and rail) and port links. The inclusion of the transport networks and ports is extremely important; key transport routes (e.g. a key railway link) may often be impacted (e.g. by flooding) far more than individual sites due to their large geographic exposure and multiple potential failure points. Extreme weather events causing loss of life and major economic damage continue to be front page news. According to the World Meteorological Organization, January to July 2007 ?was marked by record weather extremes in many regions across the world.? Inevitably, the associated phenomena are starting to impact business and investments, not so much as deal breakers, but in changing the parameters of risk management and the approaches required to devise mitigation measures. EXAMPLES OF EXTREME WEATHER EVENTS No one event can be presented as directly attributable evidence of climate change, however climate change projections suggest that the frequency and severity of many extreme weather events can be expected to increase in a warming world. In August 2003, a heat wave struck Europe, with temperatures as high as 42°C (108°F). As summer temperatures in much of northern Europe rarely exceed 30°C (86°F), the area was unprepared for the disaster, and many thousands of deaths occurred. In August 2005, Hurricane Katrina caused catastrophic damage along the Gulf Coast of the United States, forcing the effective abandonment of south-eastern Louisiana (including New Orleans) for up to two months and damaging oil wells that resulted in increased oil prices. Katrina killed over 1,800 people and caused at least $75 billion in damages, making it one of the costliest natural disasters of all time. This was followed in September, by Hurricane Rita which left 119 people dead along the U.S. Gulf Coast, causing $9.4 billion in damage. In January 2006, hundreds of people were killed when Russia, Eastern Europe and Scandinavia experienced the coldest weather for decades. In summer 2007, dramatic floods in the south central region of England, UK left 350,000 people without drinking water and many without electricity. Transport infrastructure was severely disrupted; combined with floods which occurred earlier in the summer in Yorkshire (North England), the damage is estimated to total over £2 billion. ASSESSING RISKS FROM CLIMATE CHANGE To date, only a minority of companies have attempted to quantify the risks from climate change. However, investors are seeking greater disclosure of climate change related risks and opportunities and it is expected companies that can demonstrate they are prepared for climate change will attract higher market valuations. Climate Change Threats A variety of climate change threats were examined for their potential to have a potential measurable impact on the mining company?s business operations. Those considered most significant were included in the study and are shown in Table 1 (see Appendix A). Certain threats can be considered as being cyclical in nature and the future predictions may suggest a change in the frequency and severity of such events (e.g. storms/hurricanes, rainfall, drought). However other threats are associated with a gradual change over time (e.g. loss of glaciers, loss of permafrost, sea level rises). A slightly different approach is needed to address this differing nature of the threats, as described subsequently. Climatic Regions Much of the research and data associated with climate change is collected and reported on a regional basis. An example of the climate change impacts predicted for a number of climatic regions is shown in Table 2 (see Appendix A).

Jan 1, 2009