Search Documents

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By K. Kotwica, P. Gospodarczyk, J. Sosnica, J. Pawlik, Z. Iwulski, K. Pawlik

The paper presents problems resulting from the mobile mining machines functioning and requirements concerning a machine control system, which controls successive operation stages of such machines. The problem is presenting on the example of a mobile hydraulic support to remove residual pillars in copper ore mines. The paper describes an algorithm and a flow chart to be followed when designing a supports control system. Design of control systems to ensure machine function under given circumstances is also presented.

Jan 1, 2003

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Neri Roux, Chris Budgell, Allan Cramm, Leo Cheung

"Anaconda Mining Inc. is investigating potential improvements and expansions to their operating plant located on the Baie Verte Peninsula in Newfoundland. An extensive batch and continuous bench scale testing program was launched to investigate the efficiency of cyanide destruction under different conditions in order to improve tailings handling. The primary objective of the cyanide destruction study was to apply new technologies to develop a novel cyanide destruction system.Effluent and slurry from Anaconda Mining Inc.’s Point Rousse Project was received at RPC where test work was conducted. Various sodium metabisulfite (MBS) dosages were evaluated and the use of utilizing ozone and ultra violet (UV) light to oxidize cyanide was investigated. All the data was evaluated and mass balances were compiled to develop several flowsheets. Overall encouraging results were found using a combination of ozone and MBS.IntroductionAnaconda Mining Inc.’s Point Rousse project includes an operating gold processing plant located on the Baie Verte Peninsula in Newfoundland which is in the process of improving and expanding. This plant comprises of milling and flotation followed by cyanide leaching in order to extract the gold. The residue from cyanide leaching is filtered by drum filters prior to being clarified for the Merrill-Crowe process. Once the gold has been recovered by the Merrill-Crowe process the effluent is filtered by filter presses and the resulting filtrate as well as the solids from the drum filters are detoxified prior to being pumped to the tailings pond along with the flotation tailings.The entire process is very dependent upon the efficient destruction of cyanide in the effluents and successful tailings handling. Substantial amounts of effluent are delivered to tailings ponds after gold extraction which could create environmental problems if the regulations are not met. Environmental regulations stipulate that final effluents contain no more than 1 mg/L Total CN.The detoxified tailings of the Point Rousse project are produced by the INCO SO2-Air circuit depicted in Figure 1. These detox tailings contain 10 mg/L Total CN at that point of the circuit and this was selected as the target to be matched while reducing overall MBS consumption rates from 3.2 g/L per minute. Prior to detoxification, the filter press tailings contain 520 mg/L Total CN while the drum tailings contain 29 mg/L Total CN."

Jan 1, 2017

By C. S. Kucukkaragoz

An ilmenite concentrate was reduced in the solid state with carbon under argon atmosphere at temperatures between 1000oC and 1400oC. The ilmenite concentrate and 50% excess carbon were reacted to achieve the highest attainable degree of reduction at each temperature and the reaction products were subjected to a series of analytical work by optical microscopy, X-ray diffraction analysis and SEM ( EDS) analysis. The ilmenite remained unaltered at 1000oC and had a slight change in its composition at 1050oC. A secondary oxide phase containing metallic nuclei was detectable at 12% reduction at 1100oC. The reduction of TixOy took place in a sequence changing the y/x ratio from 2.0 to a value less than 1.0 at 84% reduction at 1400oC. Metallic phase consisted of Fe and C initially and started to include Ti at the later stages. Complete reduction of TixOy to metallic Ti was not possible at these temperatures.

Jan 1, 2005

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

In 1973, US Borax & Chemical Corp. began investing three days wages and about $20 in training materials in every new employee before having him report to his first job. The result? Accidents involving new employees in the past two years have dropped by more than half from the 1972 level. What made this success possible was safety training done with programmed instruction materials-which, incidentally, US Borax also uses for vocational training.

Jan 4, 1976

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By Dean Lindsay, Inna Dymov, Mariam Melashvili, Jim Smolik, Chris Fleming

"This paper presents results from the proposed cyanide detoxification circuit for Seabridge Gold’s KSM project. The proposed flowsheet uses a two-stage CCD (counter-current washing/decantation) circuit to transfer the flotation products CIL(carbon-in-leach) barren solution to a SART process (Sulphidization, Acidification, Recycling of precipitate, and Thickening of precipitate) to recover copper and free cyanide from the copper cyanide complex. The SART barren solution is then treated by an AVR process (Acidification, Volatilization of HCN gas, and Reneutralization) to concentrate the cyanide that was liberated in SART for recycling to leach. The washed CIL barren pulp (the CCD underflow) is treated with the SO2 /Air process to oxidize residual cyanide.The goal of this complex flowsheet is to recover and recycle as much cyanide as possible and produce a final effluent containing less than 0.5 mg/L copper and CNWAD at the lowest cost. The SO2/air process is capable of achieving low residual CNWAD (<1 mg/L) in the final product, but the persistence of aqueous copper above the target level has been detected in the treated solution in some instances. The expected high concentrations of copper and cyanide in the KSM CIL barren ( >200 mg/L each species) and the difficulties this might create for the SO2 /air process was a key factor in the decision to consider including the washing, SART and AVR steps in the project flowsheet.The target concentrations of CNWAD and Cu were readily achieved after aging the SO2 /air treated pulp, as would occur in a tailing or polishing pond. This suggests no additional treatment will be required to sustain low levels of these species in the final plant effluent."

Jan 1, 2015

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By G A. Ekama

This paper describes a novel system for the biological sulfate reduction (BSR) of acid mine drainage (AMD) using primary sewage sludge (PSS) as carbon source in an upflow anaerobic sludge bed (UASB) reactor configuration. A UASB reactor was operated at a temperature of 35¦C and it received PSS (1875 mg/L COD) augmented with sulfate (1500 mg/L SO42-). The experimental results indicate that a high treatment efficiency was achieved at more than 90 per cent sulfate reduction at a liquid hydraulic retention time (HRT) of 13.5 h. In this study, the effects of various operational parameters were also investigated. The effect of a biomass recycle stream from the top to the bottom of the sludge bed was found to initiate rapid BSR from the bottom of the bed. Profile tests showed that effective and immediate sulfate reduction was achieved as soon as the influent entered the reactor. From these results, it can be concluded that the UASB configuration using PSS as energy source would be a viable method for the BSR of AMD.

Jan 1, 2009

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986