Search Documents

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By I M. Turnbull

QMAP (the Quarter Million Mapping Programme, 1:250 000 scale) is a geological mapping programme which will build a digital geological database of the whole country and publish maps and books to document it. The programme was established in 1993, following a recommendation by a review panel appointed by the Ministry of Research, Science & Technology, and is funded by the government, from the Public Good Science Fund. The relevance and fundamental value of QMAP lies in the greatly improved geological knowledge it will provide for researchers and other end-users of geological information.   QMAP research involves assessment of previous work, field and laboratory investigations in key areas, and data storage, manipulation and publication using Geographic Information Systems (GIS) computer technology. The QMAP digital database of New Zealand geology will be completed by 2006, as will the series of 21 full colour printed geological maps and accompanying explanatory texts. Two are already completed and published (Kaitaia and Dunedin), and six other projects are well advanced.   QMAP information will also be available in digital form. Next year we hope to expand the scope of the programme to cover the reconciling and linking of many other earth science databases to QMAP, because we believe this will create a powerful research tool. The intention is to develop internet access to the databases, to make the information publicly available.

Jan 1, 1997

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

To the industrial geologist, as wen as to the general or historic geologist, the possession of a reliable key to the true order or sequence of the stratigraphy or position of the various upper rocky envelopes of the earth's crust, is, equally, a desideratum of the utmost importance. Of similar value to the two groups of students is the possession of facts which throw light upon the relationships which subsist between the puccessive rock formation of different countries, especially between countries lying close to each other, or within the same great geographical division.But there is necessarily a fundamental distinction which marks the respective limits of the field of observations of the industrial geologist, and the purely historic interest of the general geologist. The former has a more definite though less extensive scope. The scope of the latter is wide and indeterminate. In short, the observations of the industrial geologist are, 'from a commercial or economic point of view, of a more practical character, and are, therefore, intentionally restricted to the study of all geological questions which throw light upon the rocks which yield products of economic value and only include the study of the character and history of other rocks, in so far, as they afford aid to the more perfect comprehension of the best manner in which materials of economic value are likely to be sought, and the best means whereby these products may be secured for the material advantage of the community. The motive of the general geologist-in most cases-is a love of the study of some particular branch or province of the geological field, and the fascination of opening a new volume in nature's library, and the hope of extending the realm of knowledge, however slight, are often sufficient, as a motive, to enlist the energy and life's devotion of the true brethren of the hammer, irrespective of considerations regarding the commercial utility of the pursuit.

By E. C. Baker

Costs of disposing of steel slag are estimated based on the present method and a proposed alternate method for a steel mill in the Pittsburgh area. Estimated cost data were calculated by the Bureau of Mines and do not reflect the investment and operating costs and credits of a specific steel mill and processing plant. The alternate method of steel slag disposal would result in an appreciable cost savings to the mill and concurrently supply the industrial and commercial markets with low-cost, high-quality construction materials.

Jan 1, 1970

By M A. Mongillo

Most geophysical and geochemical data collected during regional exploration programmes are in vector form (location, value), and have traditionally been presented and interpreted in a profile or contour map format. However, the human vision system can interpret data presented in image format much more easily and new information is often revealed by the judicious application of powerful interactive computer image enhancement techniques. This paper describes a practical demonstration of the application of such tools to gravity and resistivity datasets from the Central Volcanic Region of theNorth Island.   Filtering, contrast enhancement, relief shading, pseudo-colouring and then overlaying of the gridded datasets in image format has helped identify inter-relationships such as the association between many low resistivity anomalies (epithermal deposits or geothermal resources) and the edges of large gravity anomalies (calderas or grabens). Similar revelations should result from the application of these tools to the integration of other mapped datasets from geophysical, geochemical and geological disciplines.

Jan 1, 1992

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011