Search Documents

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Etienne S. Bieler

Mr. Chairman, Ladies and Gentlemen, I come to you tonight distinctly as a physicist, not as a geologist or a mining man. My experience in applied geophysics has been short, and I do not doubt that many of you have a much larger acquaintance: with the subject than I have. A little over a year ago, the firm of Alderson, MacKay & Armstrong decided to investigate the possibility of developing a new method of electrical prospecting suitable to our northern Quebec and northern Ontario conditions, and asked me to take up the work. A preliminary survey of existing literature convinced me that the field of induction methods was most promising. I wish to give you some account of the work carried on last summer in the Rouyn district in this connection with the very able assistance of Mr. H. G. I. Watson. Geophysical methods of prospecting can be divided generally into four classes: magnetic, electrical, gravitational, and seismic. Each class depends on the existence of a definite property in which the valuable mineral to be discovered differs materially from the surrounding rocks. In the four classes, the property will be, respectively, magnetic permeability, electrical conductivity, density, and elasticity. By far the largest differences occur in the case of electrical conductivity, where it is not rare to find ratios of the order of several millions, or even billions, between ores, sulphide ores especially, and the surrounding rock. Hence the sensitiveness and delicacy of electrical methods. Of these four classes, only two, the electrical and the magnetic methods, have been put to extensive practical use in the discovery of metallic ores. The other two classes are important mainly in connection with oil detection.

Jan 1, 1928

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Kobayashi M, Kametani H

Particles of nickel flash furnace malle (45 per cent i) were oxidized in a dropping-particle furnace. The particles melted and the molten drops simulated those produced by the atomization of molten matte. The partly oxidized droplets were quenched and then reacted with silica flux to form high-grade matte (70 per cent i) and a fayalite slag. This paper describes the experimental equipment and deals with chemical aspects of the investigation such as volatile impurity distribution and thermodynamic considerations. The overall behaviour of minor elements such as Cu, Co, As and Pb was similar to that observed in conventional converting.

Jan 1, 1986

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

When asked to lecture at Bendigo on the geological factors that determine the depths of ore deposits, I hesitated for a little before agreeing to lecture on the theory of deep ores in the city world famous as the pioneer of deep gold mining. If there be one place, wherein the conditions of deep-seated ore deposits should be sufficiently well understood, it is the city where the 180 mine made its bold plunge to previously neglected depths; and where the record of that famous mine has been broken by the skill of the managers, and the pluck of the proprietors, of the New Chum Railway and Lazarus mines.In the face of such practical triumphs, theoretical discussion may seem a waste of time, especially since it is often dedared that the existence of such deep-seated ores was denied by geological theory. This assertion is, however, startling since the oldest and best supported geoiogical theory of ore deposits, has taught for more than a century tliat ores must descend far below the regions of practical mining. This charge against Victorian geologists is generally based on opinions attributed to the late Sir Fredrick McCoy. It has been repeatedly affirmed that he declared that gold cannot occur pelow a depth of 300 feet. But so far I have not been able to discover that McCoy ever made any such assertion or ever held such a view.

Jan 1, 1902

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By R C. A Minnitt

The Witwatersrand Supergroup is host to the world’s largest gold deposits. The location, quantity, grade, continuity and other geological characteristics of a Mineral Resource are either known, estimated from specific geological evidence and knowledge, or interpreted from a well constrained and portrayed geological model. Establishing such a model is an integral part of the evaluation process in the Anglogold Ashanti (AGA) group, and is referred to as a Geoscience Business Model for the mining operations. The geological model established over the years has relied on detailed descriptions of the mineralisation, and understanding of the regional and local geology of the Witwatersrand sediments, in the West Wits and Free State goldfields. The processes of data collection in regard to underground stope and developing mapping, structural and sedimentological mapping, and the geological inputs to mine planning systems are described, together with aspects of drilling, sampling, grade control, and data management. Anglogold Ashanti’s Geoscience Department employs a complex and unique process to generate the Mineral Resource, including a 3D geological structure model of the orebodies which are usually highly faulted, and a robust mineralisation/facies model on which the decisions about domain boundaries are established. A Mineral Resource Inventory System (MRIS) has a dynamic graphic interface to the resource database that is used for compiling the resource statement. It is also used to determine the gold-called-for, as well as short and long-term planning. A unique estimation process using the extensive closely spaced stope face sampling database and the more widely spaced surface drilling information is used in combination in the Macro Co-Kriging estimation. The use of different support sizes in the C0-Kriging process is preceded by the equally unique ‘clusterisation’ and ‘acceptorisation’ procedures by which the data are quality controlled and assured prior to their use in the kriging process. The Mineral Resource and Ore Reserve estimates are classified according to the SAMREC code through a method that ensures that they are compliant, auditable, transparent and reconcilable with previous Mineral Resource and Ore Reserve statements.

Aug 22, 2011

Confirmation that acid drainage (AD) was a significant environmental issue for the Australian minerals industry came in 1992 with the first national workshop on the topic. Subsequently the extent of AD was documented in a national survey published in 1997. The recommendations arising out of that survey served as a platform for actions by government, industry and industry-support organisations such as the Australian Centre for Mining Environmental Research (ACMER) to enable more effective prevention and management of AD. This paper briefly documents the extent of AD in the industry, the government regulations and guidelines for AD management, industry initiatives, the role of ACMER and other organisations in assisting industry through research and technology transfer, and the efforts being made to deal with AD at derelict mines. Future management of AD in the industry will be assisted by the linkage of Australia (through ACMER) into the International Network for Acid Prevention (INAP) which is facilitating the interchange of knowledge on AD as well as coordinating global research on the topic.

Jan 1, 2003

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can't run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator's station. Components and service procedures on page 59.

Jan 1, 1976

By Leslie C. Richards

Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others. Introduction: Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951