Search Documents

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By F. J. Arriagada

Where gold is present in a finely disseminated form within sulfide particles, the porosity and surface area of the calcined material strongly influence leaching since they control the penetration of solution inside the gold-bearing grains. On the basis of a stability diagram for the Fe-O-S in the temperature range of 400 to 750aC, the expected sequence chemical transformations associated with the oxidation of pyrite is discus-sed. By using analytical techniques which include scanning electron microscopy, X-ray diffraction and BET gas adsorption, the chemical and structural changes experienced by auriferous pyrite-arsenopyrite concentrates and pure pyrite samples are studied under an oxidizing roasting atmosphere of com-position 80% N + 20% O2 in the temperature range of 450 to 750°C. The results indicate that as the roasting temperature increases, the surface area of the calcines decreases sharply after a maximum value attained at about 450-500°C. SEM micrographs show that the needle-shaped tips which characterize the surface of the oxide product become wider and the size of the pores between them is decreased when the roasting temperature is in-creased from 550 to 750°C. This effect suggests that the formation of a more "closed" hematite product at higher temperatures is due to sintering associated with a faster growth and crystallization of the oxide. A strong correlation is shown between increasing roasting temperature and increase in gold lost in cyanidation tailings, an effect which may be partly attributed to the loss in surface area of the calcines.

Jan 1, 1982

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that 'non-traditional' custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Zhenglong Li

A process has been developed to recover titanium from a blast-furnace slag which contains about 20-25% Ti02 and 12% Fe. In this process. "hot" slag from the blast furnace is directed to a separate furnace where it is reheated with additives to form two simple slag phases: one is titanium enriched anosovite (Ti3O5) and the other is a titanium lean non-crystal glass phase. The modified slag is then processed by conventional beneficiation techniques to produce a marketable titanium concentrate and a usable slag material. This paper focus on separating anosovite from glass by electrostatic separation and froth flotation.

Jan 1, 1996

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By Takao Mori

Novel rare earth boron icosahedral compounds are investigated as potential high temperature thermoelectric materials. REB50-type compounds and REB22C2N compounds were synthesized and the thermoelectric properties measured. Seebeck coefficients in excess of 200 V/K are observed at temperatures above 1000 K for the REB50-type compounds. Strikingly, n-type behavior was observed for REB22C2N. Up to now, non-doped B12 icosahedral compounds have all been p-type. The discovery of an n-type compound is extremely important in terms of the potential development of this class of compounds as viable thermoelectric materials. Low thermal conductivities of < 0.03 W/cm/K at room temperature was observed for these rare earth boron cluster compounds.

Jan 1, 2006

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By P. Kerr

Iron segregation is pre-dated by copper and nickel segregation processes for which the experimental methodology and reaction chemistry were established. The accepted reaction sequence for segregation involves the generation of hydrogen chloride, the chloridization and volatilization of the metal chloride, and precipitation of the metal from the metal chloride in the vicinity of carbon. Iron segregation roasting offers a potential extraction solution for processing oxide deposits with complex mineralogy or waste streams such as Minette-type iron deposits, nickel laterites, ilmenite, red mud, electric arc furnace (EAF) dust, mill scale and slag. After subsequent magnetic separation, one is left with a high grade metallic iron powder which can be marketed for powder metallurgy or briquetted to serve as a direct reduced iron (DRI) product. The non-magnetic product is typically concentrated oxides including rutile, alumina, or oxides of V, P, and rare earths, etc. that may be economically recoverable with subsequent processing. While operating conditions vary for different metals, they share the requirements of an elevated operating temperature and a mixture of oxide ore, carbonaceous additive and a chloride additive in varying amounts all in a closed reactor to allow for reducing conditions and contain the volatile chlorides. This process is then followed by some form of physical separation. Testwork performed by the authors shows promising results that may aid in future development of the process. Segregation roasting of iron will likely never displace traditional beneficiation and ironmaking technologies; however, it has great potential in niche markets where traditional technologies have failed or current technologies generate substantial waste.

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Eric Pirard

Theoretical studies carried out on shape analysis supply mathematical tools to analyze the influence of grain shapes on ore beneficiation. In the case of statistic images like those encountered in applied mineralogy parametrical and harmonical analysis methods are used. It is important that the shape parameters are adapted to the specific processes involved in ore beneficiation, while remaining easy to manipulate. The inertia parameters are considered in the scope of granulometric and gravimetric processes It appears that they are able to distinguish between the resulting products where very popular shape parameters are not. The measured statistics are analyzed through discriminant analysis procedures in order to estimate the importance of morphological differentiation and the aptitude of shape parameters to account for this.

Jan 1, 1989

By W. E. Straszheim

Computerized microscopic techniques were used to determine the size and identity of the ash-forming mineral components, as well as their association with the organic coal matrix, in order to aid in the development of physical methods of beneficiation which require such characterization for the most effective cleaning. Examples of particle size measurements, mineral phase identification, and especially coal-mineral association results are given for selected samples of raw and physically cleaned coals. These measurements can reveal certain characteristics of coals which can be be of significant value in predicting coal recovery and mineral matter rejection for coals undergoing beneficiation.

Jan 1, 1989

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015