Search Documents

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"The main idea of the report is that the yield surface can be presented as thick, ""foamed surface"" with dimensionality exceeding two. By other words, perhaps, the yield surface is fractal, i.e. it belongs to the class of geometric objects with fractional dimensionality. Apparently, fractal structure of the yield surface is determined by the fractal structure of natural materials. ""Cloud of internal stresses"" term is introduced to describe the stress distribution in representative volume element. Its plastic flow is determined by the interaction of this cloud with the thick yield surface. Thick yield surface and internal stress cloud concepts allow to determine an additional correlation between micro mechanical models of polycrystals and phenomenological theory of plasticity.1. IntroductionClassical plastic flow models are not satisfying the modem requirements. There are two main directions in their development. The first, mathematical, is connected with the development of the general theory of rheological relationships; the second, physical, is connected with the development of the representative volume element (RVE) models which are based on specific ideas about deformation mechanisms. Within the framework of the first direction, the macroscopic experimental data is formalized; the second approach deals with the generalization of physical research results for the different scale levels that are involved in plastic deformation.These approaches have advantages and disadvantages. In phenomenological theories, the advantages are the mathematical simplicity and laconic formulation of constitutive relations, which allows using them in practical calculations. However, the mathematical models of this class can not be considered as general, they are useful only for the description of limited range of deforming processes. On the other hand, physical theories that are based on the description of real plastic deformation mechanisms are very explanatory and predictive, but they lack mathematical simplicity. The above circumstances lead us to the necessity of compromise that can be found in determining the constitutive relations for RVE, which structure and parameters would bear the information about rnicrolevel and mesolevel phenomena. In this synthesis direction, the fundamental role belongs to [1,2], etc."

Jan 1, 2001

By K. E. Gonsalves, G. M. Chow

"Nanostructured powders (particle diameter of 1 - 100 nm) have uses in electronic, magnetic, structural, thermal applications as well as advanced processing of materials. Among many methods of making nanostructured powders, chemical routes offer many attractive features such as feasibility of cost-effective bulk quantity production, design of chemistry at the molecular scale, and chemical homogeneity of the powders. In this talk, two systems of chemically synthesized nanocomposite powders are presented, namely, granular magnetic materials of Fe-Cu and Co-Cu, and thermal-structural materials of AIN-BN. Synthesis and processing, characterization and properties of these materials are discussed.IntroductionNanostructured powders (particle diameter of 1 - 100 nm) are attractive materials because of many useful properties (e.g. catalytic, optical, magnetic etc.) and processing advantages (e.g. lower sintering temperature) [1]. There are many methods of making nanostructured powders, for example, physical and chemical vapor deposition, mechanical attrition, and solution chemistry [1, 2]. A common method of making composite powders involves the grinding, mixing and blending of constituents powders, but it has the limitation of inhomogeneous mixing. Chemical routes have many useful features. Using solution chemistry, precursors can be molecularly tailored and homogeneously mixed at the molecular level. The chemical approach may result in better properties of the final product. Compared to vapor-phase fabrication techniques, chemical routes are more cost-effective in producing large quantity of material. In addition, control of particle size, size distribution and stabilization of the nanoscale particles against agglomeration can be more effectively manipulated via solution chemistry.In this paper, we present an overview of some of our work in nanocomposite powders prepared by solution chemistry. Metallic systems of FeCu and Co-Cu, and ceramic system of AIN-BN are discussed. The powders were characterized using x-ray diffraction (XRD) , scanning electron microscopy (SEM), conventional and high resolution transmission electron microscopy (TEM, HRTEM), vibrating sample magnetometry (VSM), inductively coupled plasmaatomic emission spectroscopy (ICP-AES)."

Jan 1, 1994

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000

By Thomas J. O'Keefe, Pu Yu, George Houlachi, Xuewen Tang

"Impedance measurements were used to investigate the electrochemical characteristics of acidic zinc sulphate electrolytes containing Sb3+, gelatin and their mixtures. The data were correlated with cyclic voltammetry curves made using synthetic as well as industrial electrolytes. The cyclic voltammetry results were similar to those obtained in previous studies in that antimony caused a depolarizing effect while gelatin gave an increase in the potential for zinc nucleation on an aluminum substrate.The electrochemical impedance spectroscopy (ElS) evaluations were conducted on electrodeposited zinc at three overpotential values. The potentials were chosen to represent various current density regions in the zinc polarization curves. The antimony and gelatin gave characteristic impedance plots which correlated with expected behavior, particularly current efficiency. Both antimony and glue appear to modify the intermediate zinc reaction sequence, but in different ways. The data strongly suggest that film formation and stability are major factors in the zinc ion reduction mechanism.IntroductionThe zinc electrodeposition process is sensitive to the presence of a variety of organic and inorganic chemical species in the electrolyte [I]. Such components can produce either beneficial or harmful effects, depending on their relative concentrations and electrochemical behavior. Extensive investigations have been made to gain a better understanding of the changes occurring during zinc deposition in the presence of such additives. Techniques employed include microscopy, x-ray diffraction, dynamic voitammetry, current imd energy efficiency studies [2-5]. Ultimately, the objectives are to identify the factors which most affect the efficiency of the process and to provide a means to effectively control them.One of the most harmful impurities is antimony, which can be detrimental when present at concentrations as low as 10 to 20 parts per billion. Dramatic changes in zinc polarization behavior, deposition structure and current efficiency have been observed with antimony in the electrolyte. Antimony appears to lower the hydrogen overpotential by hydride formation or a similar catalytic mechanism, which allows an increase in localized corrosion and zinc dissolution [6-8]."

Jan 1, 1997

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Continuous and aligned fiber composites provide the highest possible reinforcement for a polymeric matrix. In particular, the impact resistance is significantly increased in comparison with a low energy absorbed brittle polymer. For this reason, investigations have been carried out with both synthetic and natural fibers as a way to improve the toughness of polymeric composites. Among the natural fibers, ramie was not yet been studied for its reinforcement effect to make tougher polyester composites. Thus, the present work assesses the impact toughness of polyester composites incorporated with different amounts of ramie waste fibers.IntroductionIn most engineering and other technological areas, the use of materials associated with low energy processing conditions is gaining attention for the possible environmental benefits. This offered an incentive towards the substitution of natural renewable and biodegradable materials for the traditional energy intensive synthetic materials [1]. Natural fibers from both origins: animal, such as silk and wool, and vegetable, such as cotton and jute, are typical examples of those environmentally friendly materials. Low cost and highly reduced processing machinery wear are important advantages of the natural fibers over the most common synthetic ones such as glass fiber and nylon. For these reasons, polymeric composites reinforced with natural lignocellulosic fibers have nowadays been the subject of investigation [2,3].The mechanical strength is one important property of lignocellulosic composites to access the possibility of uses like structural materials for building parts such as doors and panels, as well as furniture. In this case, mechanically strong fibers like sisal, jute, curaua and ramie [4-7] are most convenient. Moreover, the relatively low fiber/matrix interfacial shear stress in these composites is associated with higher impact energy. In fact, a greater energy has to be expended for the rupture of a weak interface. The many cracks that are formed by impact tend to branch during the fiber pullout from the matrix [8]. A larger number of cracks correspond to a greater fracture surface and consequently higher toughness."

Jan 1, 2008

By H. J. Thevik, A. K. Dahle

"A mathematical model that calculates the stress development in a coherent and stationary dendritic network due to interdendritic flow is proposed. The fluid flow is assumed to be related to the solidification shrinkage, and under the assumption of no porosity formation and unidirectional solidification, the shrinkage-induced flow within the mushy zone is calculated analytically. The interdendritic melt flow exerts a force on the solid network and an analytical expression for the stress build-up in the network is developed. Parameter studies illustrating the influence of cooling conditions, mushy zone length, dendrite coherency, fraction solid, volume fraction of eutectic, and solidification shrinkage upon the stress development within the solid network are presented. Comparing the magnitude of the calculated stresses to measurements of the strength in equiaxed mushy zones shows that it is possible for the stresses to exceed the strength, thereby resulting in reorientation or collapse of the dendritic network.IntroductionInterdendritic fluid flow is at present regarded as a very important mechanism for feeding of shrinkage during solidification of metal alloys. Solidification of many alloys is often characterised by heterogeneous nucleation of the primary phase on substrates in the melt with subsequent evolution of equiaxed dendrites. These equiaxed dendrites can initially grow freely, but impinge on each other and form a continuous dendritic network, ie. dendrite coherency, quite early in the solidification process. Measurements of the dendrite coherency point have shown that the dendritic network is established at solid fractions ranging between 0.1 and 0.5, and most often around about 0.2 [l]. Depending on the alloy composition this means that as much as 70 to 80% of the volumetric shrinkage has to be compensated by flow of liquid through the interdendritic network. Interdendritic flow occurs with a much larger resistance compared to free flow of the liquid and flow of a liquid with dispersed crystals. The pressure drop associated with the interdendritic flow increases rapidly with decreasing fraction ofliquid."

Jan 1, 1999

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Natural fibers are gaining attention as a class of low cost, biodegradable and renewable materials that also exhibit some interesting properties for specific applications. In particular, the incorporation of some natural fibers in polymeric matrix composites is nowadays providing opportunity of manufacturing a variety of industrial items, for instance automobile interior components. Among these fibers, ramie (Boehmeria nivea) is one of the least investigated and only recently was studied as polymeric composite reinforcement. Therefore, the objective of this work was to evaluate the possibility of ramie waste reinforced polyester composites to replace conventional building materials, such as plywood, plastic boards and gypsum panels in terms of a cost-benefit analysis.IntroductionThere is a growing concern over the environmental questions that are presently affecting our society in a global sale such as climate changes and generalized pollution. Among the solutions for these questions, the replacement of energy intensive materials, especially those long term degradable such as the synthetic fibers, is already being considered [1]. As a consequence, the past decades have witnessed an increase in research devoted to new biodegradable materials obtained from natural resources mainly the biomass. Important examples are the renewable natural fibers as well as composites incorporated with them [2,3]. In addition to their friendly status with respect to the environment, well know natural fibers like jute, sisal, wood, coir, hemp and flax are relatively low cost and recyclable. In recent works [4,5], the use of these cultivated and abundant lignocellulosic fibers was investigated as the reinforcement phase in polymeric composites.Other less know lignocellulosic fibers have also been recently investigated [6,7]. These are fibers that likewise show a potential of incorporation into the polymeric matrix of composite materials. Most of these less know fibers are typical of tropical regions and, in principle, their application in industrialized composites would represent job opportunities for developing countries in Africa, South Asia and Latin America."

Jan 1, 2008

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By Honorio Oliveros Gómez, Oscar Jaime B. Restrepo

"Colombia produces nine tons of electronic waste per year and there are approximately 60 tons accumulation generated in the last nine years. This work aims to establish a general methodology in the laboratory to recover gold, silver and platinum group present in electronic waste, also explore other forms of recovery of metals contained in electronic waste. We selected seven types of electronic cards present in the computers, which have their parent desoldering electronic components. Initially, we characterized the components of the cards through X-ray diffraction and SEM, to identify the metal species and composition. Tests were conducted laboratory hydrometallurgical recovery of metals. This paper proposes a methodology for laboratory-scale work.INTRODUCTIONColombia produces nine tonnes of electronic waste per year and build there in about 60 tons generated in the last 9 years [1], Computers, TVs, audio equipment, monitors, cell phones, remote controls, printers and operated toys battery, among others are part of this inventory, which mostly comes to landfills, because the lack of legislation to control the final destination of waste electrical and electronic equipment, and lack of efficient technologies to recover materials [2]. Under these circumstances which have environmental implications, technological and economic recovery is essential metals present in the electronic cards of computers, by hydrometallurgical with subsequent base metal electrodeposition [3]. Pyrometallurgical route is discarded by major implications for economic and environmental [4]. Recovery From this perspective, the determination of the metal fraction and the relationship between the different metals, using the SEM characterization techniques - BSE and XRD is indispensable [5] It follows with electrolytic dissociation processes in the leaching and electrodeposition [6], and unit operations in the laboratory to carry out successfully these processes on a larger scale. Were randomly selected computer twenty-four postcards for nine types of cards have different functions in the computer, which, through the absorption desoldering technique, they broke the resistance (thermal, surface, photoresist, power), capacitors (ceramic, electrolytic), diodes (silicon, germanium, high frequency), transistor (NPN, PNP), processors, integrated (high, medium and low frequency), the RAM card and pin parallel port serial"

Jan 1, 2011

By Maria G. Alves, Alexandre M. Stumbo, Francisca M. A. Pinheiro, Jonas Alexandre, Sergio N. Monteiro, Valdo da S. Marques, Paulo R. N. da Silva

"Brazil is among the few countries with potential for developing all sources of renewable forms of energy. In particular, the country is leading the world efforts of substituting petroleum based fuels for biofuels, such as ethanol and biodiesel. Most of the Brazilian petroleum, which has now achieved self sufficiency, is extracted from offshore wells located at the north region of the state of Rio de Janeiro. In view of the future depletion of petroleum, the State University of the Northern Rio de Janeiro (UENF) has created a Center for Alternative Energies (NEAL) to carry out R&D programs on renewable forms of energy. Today, the main project of the NEAL/UENF is a model park for generation of renewable forms of energy. The objective of this work is to present the structural concept of the park and discuss its contribution in terms of scientific, technological, economical and environmental benefitsIntroductionEnergy is presently a key issue in the world agenda for sustained development and environmental protection. It is of common agreement that the existing status of increasing use of fossil fuels, mainly petroleum, natural gas and coal will not only cause depletion of these resources with a consequent elevation in price but also climate changes, especially global warming. In fact, the humankind may be already facing an irreversible situation of climate alterations as well as reduction of conventional sources of energy. The worse predictions foreseen by specialists, still for this coming century, are dramatic disasters due to catastrophic weather in association with a profound energetic crisis. This scenario may, however, be avoided by actions that could effectively tackle the core of the problem. These actions have been suggested and discussed by scientists and leading authorities, especially in international symposia [1-3]. In particular, the Kyoto Protocol proposed goals for reduction of greenhouse gas emissions as well as a mechanism of carbon credits to allow for decreasing CO2 content in the atmosphere without affecting industrial production [3]."

Jan 1, 2008

By Guillermo Rios, Arbizum Cristina, Joa Viflals, Alba Sunyer

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities are located in Huelva (Spain) and account for the smelting of over one million tpy of concentrates to produce up to 260 ktpy cathodes and 900 ktpy of sulphuric acid. During copper concentrate smelting, the slag coming from the flash furnace and PS converters are treated in an electrical slag cleaning furnace. As a result of the treatment of the off gases from this furnace, approximately 2,000 tpy of a Zn-rich filter cake are produced and are sent to authorized waste managers. This paper describes the characterization of this material and the preliminary results of a new process to recover zinc as a pure zinc hydroxycarbonate while lead is collected as an indium-rich anglesite product. The behavior of impurities (Cd, As, Tl, Sn, Sb, Bi, Cu, Se, Te) in the leaching, solution purification and precipitation steps is also reported.IntroductionThe Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975, the old blast furnaces were replaced by Outokumpu flash smelting furnace (FSF) technology, and the copper refinery capacity was increased to 108,000 tpy. Between 1994 and 1996, an expansion project was carried out to increase the copper from concentrate and cathodes to 250,000 tpy and 215,000 tpy, respectively. This expansion basically consisted of a new sulphuric acid plant, replacement of the anode furnaces by two 400 t units, redesign of the slag cleaning furnace (SCF), an increase in the electrolytic cells to 1,120 and implementation of ISA permanent cathode technology. Furthermore, a debottlenecking project has led to a capacity of 1,000,000 tpy of fresh concentrate since 1997. Meanwhile between 1995 and 1998, a cathode production rate of 260,000 tpy was reached as a result of a progressive increase in the current density in the refinery."

Jan 1, 2012

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Guangxin Wu, Shunli Zhao

"Nucleation and growth model based on a 3D CAFE model, which was incorporated with macro heat transfer calculation within ProCAST software was used to predict the solidification microstructure of austenitic stainless steel in twin-roll strip casting. The simulation results of solidification microstructure agreed well with experimental results of austenitic stainless steel. The effect of different casting process parameters on the solidification microstructure was simulated. The predicted results show that solidification microstructure is obviously sensitive to superheat and convection heat transfer coefficient. With the increase of superheat, the grain density decrease and the proportion of columnar crystal increase. In addition, the proportion of columnar grains increases when convection heat transfer coefficient increases. Thus, it was demonstrated that the solidification microstructure evolution of twin-roll strip casting could be predicted reasonably by using this model.IntroductionNear-net-shape casting technology is an important research area in the iron and steel industry today. Twin-roll strip casting represents a major area of concentration of near-net-shape casting technology. It has been widely used for its outstanding advantages, such as extended solubility of alloying elements, refined solidification microstructure and reduced microsegregation [1]. Furthermore, it is the most environmentally friendly, energy saving, and C02-sensitive way to produce steel strips [2]. Therefore, much attention remains to be paid to this aspect. A lot of published works indicated that the solidification microstructure of twin-roll thin strip has obvious effect on the thin strip properties [3, 4]. For the accurate control of parameters of the process are made difficult due to the complicated process and the multi-fold factors, great attentions have been paid to numerical simulations to provide insight into the solidification behaviors of the thin strip formed by twin-roll strip casting [5, 6].Simulations of casting solidification can provide a method to predict microstructure and to improving strip quality by controlling the process parameters."

Jan 1, 2014

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By B. Balamurugan, D. J. Sellmyer, J. E. Shield, G. C. Hadjipanayis, Damien Le Ror, R. Skomski

"Rare-earth transition-metal (R-TM) alloys show superior permanent magnetic properties in the bulk, but the synthesis and application ofR-TM nanoparticles remains a challenge due to the requirement of high-temperature annealing above about 800 °C for alloy formation and subsequent crystalline ordering. Here we report a single-step method to produce highly ordered R-TM nanoparticles such as YCO5 and SmCO5, without high-temperature thermal annealing by employing a cluster-deposition system, and we investigate their structural and magnetic properties. Nanoparticles of size = 10 nm are monodispersed (s /d ~ 0.15) and have Hc values at T = 300 K of 8.0 and 4.5 kOe for YC05 and SmC05, respectively. Alignment of the easy axes is performed via a field applied to the clusters before deposition. These processing steps are highly desirable to create and assemble R-TM nanoparticle composites for future permanentmagnet applications.IntroductionMagnetic nanoparticles with high magnetocrystalline anisotropies (Ki > 1 MJ/m3) are required for permanent-magnet, recording-media, and other significant applications [1-3]. In this regard, bulk rare-earth transition metal alloys (R-TM) especially RC05 (R = Y and Sm) crystallized in the hexagonal CaCu5-type structure have shown a large Ki = 5 MJ/m3 (YC05) and 22 MJ/m3 (SmCo5) along with an appreciable saturation-magnetic polarization (Js, > 10 kG) and high curie temperatures (Tc > 1000 K) [2]. The challenges in controlling the size, sizedistribution, phase purity and crystalline ordering, however, limit the research on RCo5 nanoparticles [4,5]. The conventional arc-melting technique requires high-temperature annealing for alloy formation and subsequent crystalline ordering, which causes excess growth and thus results in nanocrystalline powders of particles sizes larger than 30 nm [6, 7]. Low-temperature wet-chemical techniques yield SmC05 nanoparticles of sizes smaller than 20 nm [5], but the control of phase purity is challenging due to the presence of surfactants and formation of other secondary phases [8]."

Jan 1, 2012