Search Documents

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By Clodualdo C. Conde

In order for Philippines Associated Smelting and Refining Corporation (PASAR) Corporation to remain a leader in the copper smelting and refining industry, continuous improvements in plant technology are required. Reliable performance of plant equipment is essential for a competitive smelting operation. PASAR is constantly searching for the best equipment and technology to allow us to manufacture products more efficiently. When the Smelter was commissioned in 1993, the Flash Furnace off-gas treatment system was a constant source of problems. There were frequent shut-downs of the electrostatic precipitator due to material buildups on the discharge electrodes and collecting plates. In 1998, the precipitator was successfully upgraded to eliminate the buildup problems and to increase the collection efficiency. The upgrade greatly reduced down time and maintenance, and the enhanced collection efficiency also eliminated pluggage problems and material losses in the Acid Plant. This extensive precipitator upgrade was accomplished during a 30-day Smelter turnaround.

Jan 1, 1999

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By C. E. Hunt

Since the turn of the century, copper-nickel sulphide ores have been processed at the Sudbury, Ontario operations of INCO Limited, currently the largest integrated mining, milling, smelting and refining complex in the free world. Through the years operational, ecomomic, social and legislative changes have dictated the need for research and development directed at mitigating the impact of existing operations on the surrounding natural environment and also the reclamation of areas affected by earlier mining activities. Approximately one hundred years of mining history and the current annual processing of some 12 million tons of ore presents significant challenges with respect to waste disposal, liquid effluent treatment and land reclamation, particularly in light of rapidly evolving environmental regulations' and controls within the Province of Ontario.

Jan 1, 1992

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By M. Giralico

Optimized mixer settler designs will now handle flows of over 25,000 GPM. The size and expense of the equipment hamper experimental settler optimization efforts. Computational Fluid Dynamics (CFD) is a timely and predictable tool for settler design development. In the past, CFD has been used to evaluate only the flow field in pumped and auxiliary tanks. A similar numerical analysis is used to evaluate settler flow and phase separation. Phase separation is analyzed using multiple species for the aqueous and organic phase. Experimental validation shows good agreement between the computational and experimental solutions in both flow field and phase separation. The computational model is used to show performance differences between various choices of settler geometry, liquid depth, with variable flow rates. Understanding the differences allows the development of optimized settler designs. System improvements are predicted to lower entrainment levels further and/or allow new smaller footprint designs. This paper focuses on the major design components of the settler and how future technological advances will lead to further improvements in their design. LIGHTNIN?s new designs will handle tomorrow?s production requirements, while maximizing profits.

Jan 1, 2003

By Fumito Tanaka

The Converting Furnace (C-furnace) of the Mitsubishi process has solely provided opportunities for producing blister copper continuously from molten matte. Continuous converting originates from the proven technology for controlling the behavior of magnetite in lime-ferrite slag of the CaO-FeOX-Cu2O system. Recent improvements in the C-furnace operation have included the slag controls reflecting the impact of minor oxides on magnetite behavior. Although previous investigations focused on magnetite behavior, sulfur has also affected the C-furnace operation because it is of practical importance to avoid the precipitation of gypsum from lime-ferrite slag and the separation of matte from blister copper. This paper will quantify the behavior of sulfur in C-furnace with respect to the gypsum formation and matte separation, and discuss better controls for C-furnace operation.

Jan 1, 2006

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By Pierre-François Bareel

EU legislation imposes ambitious recycling targets for various consumer goods. End-of-Life Vehicles (ELVs), scrap iron and various proportions of Waste Electrical and Electronic Equipment (WEEE) are processed by shredding plants which recover most of the metals but produce Shredder Residues (SR) which are landfilled. They represent 20 to 25 wt.% of the shredder input. Energy issues for the coarse fraction of SR are now largely studied. However, below 2 mm, the calorific value falls off drastically. These Fine Shredder Residues (FSR) represent up to 55 wt.% of the total SR. To meet European objectives other alternatives to landfilling must be considered for the FSR. The present paper describes a study carried out to characterise the FSR and investigates ways to process them and produce marketable products. Applying Gy's theory, a sampling procedure was conducted over two years to statistically quantify the variability of the physical and chemical properties of FSR produced by a Belgian post-shredding treatment plant. Macroscopic characterisation has led to the identification of four material categories which could be separated according to their physical properties: ferrous metals (more or less oxidised), non-ferrous metals, an organic fraction (plastics, rubber, textiles, foams, wood) and a minerals fraction (glass, ceramic, concrete). The entrainment of small metallic particles within the pores of organic fragments will affect the quality of the separations.

Jan 1, 2006

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By Kimio Itagaki

Thermodynamics and rate process fundamentals are two of the important principles involved in nonferrous production processes. The process configuration establishes whether thermodynamics or rate process behavior is most relevant in a particular application. In this paper, thermodynamic theory and rate process fundamentals are used to analyze the main characteristics of smelting and converting processes. The effect of increased oxygen potential .is examined with emphasis in view of the increased use of highly oxygen-enriched gas in modem smelting processes. Phase equilibrium and the distribution of minor elements between copper or nickel matte and FeOx-SO2- or FeOx-CaO-based slag are reviewed. The use of oxygen-rich gas has no serious effects on 'the recovery of valuable copper and silver in the matte phase, while the recovery of nickel and cobalt is adversely affected. The oxygen content in the gas also strongly affects the distribution behavior of arsenic, antimony and bismuth. Analysis of the rate processes occurring in the shaft of flash smelting, and converting furnaces by a 3-D computational fluid-dynamics model is also discussed. After being validated with experimental data collected in a large laboratory furnace, the computer model has been used to simulate the main features of an industrial flash converting operation. The results present quantitative features of the improved mixing of the particle-gas suspension and increased oxygen efficiency obtained with a distributor-cone burner compared with those with a single axial entry burner. The role of basic principles in the engineering analysis of high-intensity matte smelting processes is also discussed.

Jan 1, 2002

By Ross Baldock, Ross Andrews, Gu Helin, Lan Xu, Markus Reuter, Song Xingcheng

"A commercial lead smelter using Outotec Ausmelt TSL Technology has been successfully commissioned and put into operation at Yunnan Tin Company Ltd operations near Gejiu City, in Yunnan Province, China. The plant was commissioned in July 2010 after three years in the design and construction phase. The process uses a three stage batch process to produce lead bullion and zinc fume, and a slag that is low in metal values. The paper provides details of this lead smelting project, including the theoretical evaluation of the multi-stage process chemistry, engineering design, plant commissioning and the final operation. Comparison of the design targets and actual performance of the plant is emphasized. The fast ramp-up to full production of the largest Ausmelt TSL lead furnace built to date is highlighted.IntroductionIn 2002, Ausmelt and Yunnan Tin Company (YTC) successfully commissioned a smelter to modernise the Yunnan Tin smelter in Gejiu City, Yunnan Province, China. A single Ausmelt furnace was installed by YTC to process tin concentrate and revert materials, to produce YT Brand tin product. The advanced Ausmelt Technology furnace at YTC replaced seven existing reverberatory furnaces and provided a flexible, energy efficient and environmentally beneficial system to complement the world leading refinery facilities of YTC."

Jan 1, 2012

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Victor Bredykhin

The report is devoted to the investigation and improvement of processes taking place at contact of large quantities of water insoluble liquid and particles of solid phase in a pulp. Theoretical analysis and simulation of acting conditions have allowed to determine that after attaching of oleophilic particles on the «water-reagent» separation surface the break of a formed complex is taking place according to the reagent volume and for oleophobic minerals along the «solid-reagent» separation surface. As a result particles are selectively treated if the magnitude of the reagent adhesion to the surface of solid phase in water is great. The results of dispersion are influenced significantly by availability of sharp edges on the surface of real particles. They keep tree phase perimeter of moistening. It is possible to fix reagent in the form of lens whose contact angle is significantly smaller in comparison to the thermodynamic angle. In adhesion dispersion the reduction of reagent volume, covering the equal area of particles surface is possible when the reagent is in a pulp in the form of thin films on the «water-gas» separation border. The process is tested in laboratory conditions as well as at pilot concentrating mills in flotation of sulfide ores, non-ferrous metals (copper-molybdenum ore), native sulfur and coal.

Jan 1, 2006

By L. S. Montagna, R. M. C. Santana

"Since the industrial revolution, plastic products sector has growing bigly, however this fact presents as consequence the increase of municipal plastic waste (MPW).The aim of this work is to developmet polymer mixture from MPW with the adittion of rubber tire (TR) post use and to study the mechanical and morphologycal properties. The polymer mixtures Polypropylene/High impact polystyrene/TR (PP/HIPS/TR), where rate weight TR used was 10, 20 and 30 % and with three size particles (500, 710 e 1000 µm). The specimen tests were obtained by injection molding. Preliminary results of mechanical properties showed that the increase of TR influence in a reduction of the flexural and tensile resistance. Results by scanning electronic microscopy on the fracture surface of mixtures PP/HIPS/TR showed a better interaction of TR particle with HIPS than with PP. Also, the presence of microcavoids was observed, characteristic in PP/HIPS blends, favouring in the increase of its opacity.IntroductionOne great part of the municipal solid waste (MSW) is composed of polymer mixed since commodity plastics, blend to polymer composite. The processing of plastics mixtures for recycling has been attempted with some success, but poor mechanical properties and uncertain economic value limit their more versatile reuse. Polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), poly(vinyl chloride) (PVC) and polystyrene (PS) are among the most common plastic waste, predominantly used in packaging food industry [1].One other problem that preoccupy to the society is the increase of rubber tire waste in the proportion of MSW. In Brazil, from 1999 to 2004, 39 % from 386 mil ton of tire post-use were destined to ciment Industry as source of energy [2]. However this destiny produces one other problem, environment pollution, due to gas mixture emitted.Recycling represents a valid alternative to the disposal of post-consumer plastics in common landfills if it is possible to obtain new materials with good final properties compatible with practical and, above all, by cheap methods [3]The reutilization of group tire rubber (TR) powder as a dispersed elastomeric phase in a thermoplastic matrix offers an opportunity to design second generation materials which would be recyclable due to the thermoplastic matrix and which potentially could present thermoplastic elastomer (TPE)-like mechanical behavior. [4]."

Jan 1, 2008