Search Documents

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from Copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu10), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, Cu2O bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties of the CaO-FeOX-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation. -

Jan 1, 2003

By Akira Kaneda

Mitsubishi continuous process employs an electric furnace for settling matte from slag. Electrodes are immersed into the slag layer in the slag-cleaning furnace and the temperature of the melt is maintained at a predetermined level by Joule's heat. Electrodes are immersed to the depth where the current of each electrode is kept at a set value, and they are raised or lowered automatically to compensate for the deviation from it. Because electric resistance of the bath is varied with the matte level in the furnace and the composition and temperature of the slag, the immersion depth of the electrodes is affected by them. Therefore by monitoring the immersion depth and its change with time, abnormal situations in the furnace, such a~ rise of matte level or local abnormal state of melt, can be detected. In this paper, relations between state of the furnace and electrode behavior are discussed based on the plant data, and then a new and simple monitoring method of the condition of the furnace is proposed.

Jan 1, 2001

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

Microstructural investigation has shown that grain splitting or deformation banding ( DB ) develops progressively with increasing strains during cold rolling. Of particular significance to simulating texture development in cold rolled BCC polycrystals is the operation of higher order slip systems other than 110 and, the occurrence of DB in the rolling plane since the latter allows a new relaxation of the shears. Deformation banding ( DB ) model includes grain subdivision in the rolling plane and applies the Relaxed Constraints ( RC ) mechanism for the other shears. An energy criterion for deciding whether deformation banding occurs or not has been postulated, referred to as Deformation Banding Criterion ( DBC ). This paper reports the results of the investigations into the effects of different slip systems, i.e., those based on 110, 112 and 123 slip planes and their combinations using RC, DB and DBC models, in developing simulated BCC rolling textures.

Jan 1, 1999

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By M. J. Soria-Aguilar, F. R. Carrillo-Pedroza, S. Preciado-Nuñez

"Dust originated from the Iron Blast Furnace (BF) and the Basic Oxygen Furnace (BOF) containing alkalis and zinc are not completely recycled because due affects the process efficiency. These types of dust represents an economical lost as a consequence of values contents of iron and carbon. Several processes in aqueous media have been developed to treat the steelmaking dust. This work presents a laboratory study for reduce zinc and alkali containing in BF and BOF dust, using different acid and alkaline solutions and oxidants as ozone. The results obtained show that the elimination of zinc and alkalis can vary from 5 % to 80 % depending on the treatment conditions (the solution, the oxidant and the temperature). The dust obtained from this treatment can to be recycling to the steelmaking processes to recovery iron and carbon values.IntroductionEach one of the steel making industry processes generate several sub-products and residues containing useful units of iron, carbon and other elements that are or could be recycled to the productive process. Some of those sub products are the dust from the gas cleaning system of the blast furnace and the dust from BOF reductive process; such dusts are sent to the sedimentary lagoons. The dust represent a lost of 2 % of the total iron and coal mineral’s content feed to the process.The typical iron, carbon and zinc content of the blast furnace dust is approximately 40, 24 and 0.3 % and the content of the BOF dust are 50, 15 and 0.9 % weight respectively, with physics - chemical characteristics that became them susceptible to be agglomerated and feed to the blast furnace. But the high content of zinc does not allow recycling it into the process. At the blast furnace the presence of zinc propitiate the formation of film in the furnace wall; these elements are vaporized in the low section of the cube of the furnace and they are dragged by the gases to the top and condensed again at the cube. Part of these condensed materials strongly adheres to the furnace cover harming it and reducing the empty space of that section, causing eventually a severe perturbation of the ascendant gas flux [1]."

Jan 1, 2008

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By I. Iwasaki

Flotation characteristics of pyrrhotite by itself and in complex sulfide ores are reviewed with respect to the effects of oxidation, grinding media and other electroactive minerals.

Jan 1, 1988

By Sungdon Kim, Chuljoo Kim, Joonsoo Kim, Hosung Yoon

"This study was performed to establish the optimum leaching condition through the experiments for the oxidized roasting followed by leaching of fluorocarbonate rare earth mineral (bastnasite) using sulfuric acid, and to establish the optimum condition for the recovery of cerium by ion- sieve method from the leached solution of bastnasite. The optimum conditions for the sulfuric acid leaching by the oxidizing roasting of bastnasite concentrates are that the roasting temperature is 550 -600 °C, the roasting time is 2 hrs, the concentration of sulfuric acid is 6N, the leaching temperature is S0°C and the leaching time is 3 hrs. At this time, the leaching yield of total rare earth oxides in the leaching of bastnasite concentrates is about 91%. When cerium is recovered by ion-sieve method from the solution obtained by the sulfuric acid leaching of the roasted bastnasite, the optimum conditions are that the TREO(total rare earth oxide) of leached solution is below 70 g/l, the flow rate of leached solution is 9.6 ml/min and the ratio of height to diameter of resin packed in column is above 9. In these conditions, the recovery of cerium of yield 85% and purity 96% is possible.IntroductionThe rare earths are generally called to Lanthanides, which are totally 17 elements including Scandium of atomic number 21 and Yttrium of atomic number 39 in addition to 1 S elements from Lanthanum of atomic number 57 to Lutetium of atomic number 71. Since the separation to each element is very difficult because of their similar chemical properties, the rare earths were used as the mixed rare earths and the mischmetal without separating to each element. However, the high purity rare earths are recently produced commercially to each element so that they are used as the materials for high tech. industry such as electric and electronic materials, catalysts, optical materials, special alloy and 8Uperconductive materials, and their consumption is rapidly increasing. Therefore, the purpose of this study is firstly to prepare leached solution by using the series of process of the oxidation-roasting and leaching by sulfuric acid. Next, second purpose is the separation and recovery of cerium by ion-sieve method."

Jan 1, 1998

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011

By Congcong Yang, Jian Pan, Deqing Zhu, Yang Zhong

A study of pelletization of one imported chromite concentrate with coarse site, poor ballability and refractory roasting performance was conducted in small scale tests, and high pressure grinding rollers (HPGR) was used to improve the pelletization. The mechanism of HPGR was revealed by means of SEM images and optical microscopy. Compared with the ball milling pretreatment, HPGR pretreatment can not only enhance the ballability of pellet feed but also drop the roasting temperature. Fired pellets, containing proper chemical compositions with high compressive strength of 2917N/pellet and good metallurgical performances, have been manufactured. The mechanism of HPGR reveals that chromite particle surface turns to more irregular after HPGR treatment and more new surface being formed because of more cracks, sharp corners and edges appearing, resulting in higher surface chemical activity, all of which improve the ballability of the chromite concentrate and contribute to the consolidation of fired pellets.

Jan 1, 2015

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Ali Kucuk, Bekir Karasu, Keriman Karaveli Pekkan

"Zircon (zirconium silicate) is the main opacifier of glossy, opaque, white colored, frit-based wall tile glazes. However, zirconia containing frits employed in the preparation of these glazes increase the production cost and therefore, limit zircon usage as a raw material at industrial scale. With the present study, it was searched whether borax solid wastes could be evaluated as a component in the starting relevant frit recipes. The wastes were obtained from Eti Maden Kirka Boron Company of Turkiye. Frit production, glaze preparation, application, and fast single-firing of glazed wall tiles were conducted under laboratory working conditions in Anadolu University, Department of Materials Science and Engineering laboratories. Beside standard tests applied to the final glazed wall tiles, color and gloss analyses of the fired glazes were conducted with a spectrophoto-meter and a gloss-meter. Characterization of these newly produced glass-ceramic glazes was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques. IntroductionFrits are the indispensable constituents of most industrial glazes which mature at temperatures below 1150 °C [1]. In the traditional opaque glazes used in wall tile industry, opacity usually originates through hardening of glass matrix by adding high amounts of zirconia containing frits into the glaze batch [2]. Nowadays, researches point out that certain type of glass-ceramic layers can be alternatively employed as tile coatings lowering the use of zirconia containing expensive opaque frits. A rather high crystallization capacity of glass- ceramic glazes due to zirconia presence in glass network makes them suitable candidate as a glaze coating with a desirable micro-structure. One of the best methods to obtain an opaque glaze surface is to induce a crystal phase in the coating, whose refractive index differs significantly from that of the glassy matrix. The opacity of such coating is determined by the diffusion, refraction and reflection of light through the layer containing emerging crystals, and the degree of opacity mainly depends on the size and quantity of crystals. The development of glazes not consisting of expensive or toxic components is of special interest [3]."

Jan 1, 2008

By W. P. lmrie

The recent years have seen many copper smelting operations become uneconomic due to a combination of low metal prices, high energy and labor costs, environmental requirements and high investment costs for modernization or replacement. Since a copper commodity requirement remains, the industry will recover, but many operations will need to determine which processes can offer the best prospect for economic operation and readiness for reliable investment and implementation. Corporate investment decisions involve the judgment of many factors in addition to topical technical aspects. Consideration of plant management and operational aspects are thus included. Taking account of such proven processes as conventional, flash and continuous smelting, plus modified conventional and new unproven processes, this paper gives a systematic approach to aid optimum choice for a modernization or grassroots investment. Actual achievements in energy form alternates, conservation and cost effectiveness are highlighted, and areas of remaining potential for energy saving are discussed.

Jan 1, 1983