Search Documents

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

By Shuangsuo Yang

Coal ribs can roughly be divided into three types: (1) roof and floor rocks are similar to ribs, (2) roof and floor rocks are stronger than ribs, and (3) roof and floor rocks are weaker than ribs. Different types of roof/floor and ribs will exhibit different types of ground pressure around an entry. Most coal mines belong to the 2" type with ribs fractured or even broken. In this case the mine ground pressure depends on the occurrence and development of deformation and fracture of the ribs. If it's not properly controlled, the following deteriorating process will follow: the roof bent downward > the ribs squeezed and broken > rib sloughing and collapse > rib support to the roof reduced > the roof bent downward further > the ribs broken further. In this paper rib instability is divided into four types: compression/shear sliding rib fall, gravity sliding rib fall, cross arch rib fall, and cleavage rib fall. Since failure in thin walls is largely of tension type whereas that of thick walls by compression or shear, a concept is proposed here to utilize a thick bolted rib to stabilize entry ribs, i.e. the thickness to height ratio of the thick bolted ribs

Jan 1, 2005

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Nengxiong Xu

The WTZ coal mine is located adjacent to an auxiliary dam in P. R. China. The mining-induced ground movements are calculated using a 3-D numerical procedure based on the finite difference method (FDM) to judge whether the extraction of the coal seam will have a negative impact on the dam. First, the values of the rock mass mechanical parameters in the numerical model are estimated using the available literature that relates intact rock and discontinuity properties to rock mass parameters. Then, based on available surface subsidence monitoring data for an area in WTZ mine, the main mechanical parameters of coal and rock masses are calibrated by a back analysis procedure that combines an experimental design technique with numerical simulations. Then the reliability of these rock mass parameters is verified. Finally, according to the planned mining sequence, predictions of mining induced surface subsidence are computed in steps, and the boundary of the ground movement area of each step is determined. The nearest distance from the boundary of the surface movement area to the edge of the dam foundation was found to be about 1347 m. The maximum surface subsidence within the mining area turned out to be 2.7 m, and the maximum settlement point was found to be close to west-south corner of A2 mined area. These findings led to the conclusion that the coal seam mining would not cause dam damage.

Jan 1, 2013

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Song Yong Jin

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts, collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger.

Jan 1, 1992

By Adrian L. Moodie

Austar Coal Mine (formerly Southlands and Ellalong Collieries) has had a long association with difficult strata control conditions associated with mining depth and a highly jointed/cleated coal seam. The conditions include poor longwall face conditions, cyclic loading, heavy tailgate (TG) roadway conditions, and difficulties in maintaining stable roadways on development at 5.2 m (17 ft), as well as the geotechnical challenges of an 8.5-m (27.9 ft) -wide roadway required for installation faces. The introduction of Longwall Top Coal Caving (LTCC) to this environment has aided in the management of some of these issues, but LTCC has also given rise to other geotechnical considerations. Additional geotechnical issues associated with LTCC not only require management during operations, but also require consideration when evaluating new mining areas at Austar Coal Mine or potential LTCC extractable resources throughout Australia and the world. In September 2006, LTCC commenced at Austar Coal Mine in longwall panel A1. Since this point the LTCC face has been increased from 147 to 216 m (482 to 709 ft)and finally to 227 m (745 ft) in width, and it has also been rehanded and modified in the three fully extracted panels to date. The application of LTCC in panels A1, A2, A3, and now A4 has been very successful, both from a coal resource recovery point of view and in the management of the principal hazards of spontaneous combustion and strata control. This paper focuses on the geotechnical aspects of the application of LTCC at Austar Coal Mine and also reviews some advances in general strata control management at the mine.

Jan 1, 2011

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By Karl Brandt

Longwall panel 580 has recently been retreated in the Zollverein 1/2 seam at a depth of approximately 1000m at Auguste Victoria mine with rectangular rockbolted roadways used for both the maingate and tailgate. Although Auguste Victoria mine has been increasingly using rockbolted support since the mid 1990's. this has previously been restricted to tailgates for single use. This panel represents the first use of a rectangular rockbolted roadway as a maingate at Auguste Victoria mine. As such, it represents a significant change in support strategy. As part of the strategy numerical modelling was used to examine expected behaviour of rockbolted roadways at the site, stress changes during face retreat, the feasibility of adopting rockbolted support for the maingate and the reinforcement pattern required. Monitoring instrumentation was installed in both gates to confirm that the support systems were performing satisfactorily as the gates were driven and as the face was retreated. Although the panel is isolated from others in the Zollverein 1/2 seam, markedly different roadway conditions have been experienced in the two gate roads. Favourable conditions were obtained in the maingate, but particularly difficult conditions were encountered in the tailgate. Previous work for the mine had examined interaction with old workings in other seams and shown a vertical stress of 28MPa for the maingate and up to 45MPa for the tailgate. The values from the earlier work were used in the modelling work described, which showed contrasting results given the different stresses. The difference between the gates can be attributed to the interaction. The paper describes the numerical modelling work, the reinforcement systems adopted, the monitoring results, the interaction effects and the comparison between expectations from the numerical modelling results and the conditions actually experienced.

Jan 1, 2002

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990