Search Documents

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By T. P. Harrington

Research efforts are just beginning to identify the acoustic signatures of very short pulses of sound associated with the fracture of single particles in an autogenous mill. This presentation will discuss the anticipated correlation between these data and the fundamental mechanisms of rock fracture It is hoped that further tests will help identify what design and operating parameters influence the acoustic spectra, determine whether different minerals have different spectra and correlate product particle size distribution with acoustic spectra.

Jan 1, 1980

By Ben H. Daud

The systems optimization approach to mine planning has led to the adoption of a number of mathematical and computer models for short, medium and long range planning of mining operations. In the realm of open pit mine planning, the most common uses of such an approach have been in the areas of optimal pit design and planning of materials handling operations. Since a truck-shovel combination is the most widely used method of materials handling in open pit mines, a number of models have been presented in the past to analyze and optimize such systems. Broadly, these models can be divided into two categories. The simulation model, which is primarily used as an aid in analyzing the performance of either an operating or a proposed haulage system under the influence of externally alterable parameters, and the linear or integer model which is used as a tool for short or medium term optimization of the system under the operating constraints. In the first part of this paper, a brief discussion is presented of the linear/integer optimization models presented in the past, and in the second part a new model is described which is actually a combination of the simulation and the integer programming models. In its bare essentials, the model consists of an integer optimization algorithm, but the constraints are regularly and dynamically updated by incorporating the conclusions drawn from a stochastic simulation model of the mine haulage system. Since the successive optimization is performed by the mine operator who manipulates the constraints to guide the model towards the optimum, the mystical black box approach is minimized and should help in adoption of the model by the mine personnel. Also, by combining the stochastic simulation model and the deterministic integer model, some of the advantages of each are acquired.

Jan 1, 1976

By S. W. Thomas

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value .are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A) A relatively large size sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B) When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves.

Jan 1, 1985

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By I. Orisek

The methodology and results of a feasibility study of an Automatic Truck Dispatching (ATD) system in an actual open pit mining operation, are presented. Using mine cost data, an economic analysis confirms that capital and operating cost savings with ATD out-weigh the costs. Productivity improvement achievable with ATD is quantified with a computer simulation of truck haulage based on mine production and operational data.

Jan 1, 1986

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962

By M. A. Bouchat

The Kipushi deposit, where the Prince Leopold Mine has been installed, belongs to Union Miniere du Haut-Katanga and is located in the Belgian Congo, 20 miles SW of Elisabethville, at the vicinity of the Northern Rodhesian Border. The deposit is of the hydrothermal metasomatic vein-type; mineralisation took place, through the limestone of the, lower Kundelungu. This is a special fea¬ture of the deposit, compared to the other copper deposits of the neighbourhood, both in the. Belgian Congo and in Rhodesia. Actually, the primary mineralisation of these other deposits; is directly related to the stratigraphic systems: schistous dolomitic in the Belgian Congo and Roan in Rhodesia. Both facies are older than the Kundelungu and separated from this formation by a tectonic cataclysm. The valuable elements occuring at Kipushi are principally copper; and zinc. The deposit also contains smaller quantities of lead, precious metals and other elements including germanium.

Jan 1, 1960

By Josef J. Schwegel

The first vertical shaft lime kiln operating according to the parallel-flow regenerative principle was developed and built in the nineteen-fifties by Schmid-Hofer in Austria. Upon proving this concept of calcining or "burning" limestone to be very energy efficient for the production of good quality lime, Maerz Ofenbau AG of Zurich, Switzerland was in 1965 licensed for the design detailing and construction of these kilns. The first regenerative shaft type lime kiln outside of Austria was built in 1966 and through close co-operation with customers and their operating personnel, the advanced technical developments of today&apos;s kiln designs were accomplished. At present approximately 190 kilns of this type in capacities ranging from 60 to 700 short tons per day have been built or are under construction throughout the world in highly industrialized as well as less developed countries.

Jan 1, 1981

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation&apos;s natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By P. L. De Bruyn

[According to the Young equation, SG = SL + Coso, the equilibrium contact angle depends on the values of the three interfacial tensions involved. A solute promotes wetting, i. e. a decrease of contact angle if it decreases.LG and/or YSL or if it increases SG. Dewetting, the important step in flotation is, promoted if the solute increases y and/or SL or decreases. Most solutes used for wetting or dewetting are, positively adsorbed at all interfaces involved and consequently according to the Gibbs equation lower the interfacial tensions. Wetting is therefore expected to occur if LG and SL are more affected by the solute than SG. Dewetting on the other, hand demands a greater decrease of SG than that of SL (and of LG). See P. L. de Bruyn, J. Th. G. Overbeek and B. Schuhmann, Jr., Mining Engineering (1954) P. 519.]

Jan 1, 1960

By J. D. Cooper

Previous research developed guide- lines to restrict the placement of air velocity sensors to areas of Low turbulence in underground nines. Even though these guidelines are theoretically correct, and may be easy to follow in underground coal mines, their application in small underground metal mines is difficult. As a result, study was undertaken at the Colorado School of Mines Experimental Mine to determine if an air velocity sensor could be placed in other locations with acceptable results. It was found chat by applying a variable calibration function to correct for changes in amounts of turbulence, instead of the previously used calibration factor multiplication, the sensor could be used successfully in areas of moderate turbulence.

Jan 1, 1984

By Robert W. Cope

"Mining began, in the Colstrip area in the 1920&apos;s by the Northern Pacific Railroad. The coal was used for steam locomotives until 1957, when the advent of diesel power made them obsolete. In 1959, Montana Power Company purchased the Northern Pacific properties including the mining equipment, coal leases and the town of Colstrip. Western Energy Company, a wholly owned subsidiary of Montana Power Company was formed in 1966 to manage the mining operations in Colstrip. The Rosebud Mine officially re-opened in 1968 to supply coal for Montana Power Company&apos;s J. E. Corette Plant In Billings. Since 1970, Long Construction has operated the mine equipment for Western Energy Company". The Rosebud Mine is located in Southeast Montana and supplies coal to two 350 megawatt power plants located in Colstrip and one 180 megawatt plant located in Billings. Approximately 30 percent of Western&apos;s annual production is consumed by these plants. The remaining production is shipped to the mid-west and burned by utility companies and municipalities.

Jan 1, 1981

By C. H. McGuirk

Computerized Preventive Maintenance is important in maintaining consistent and efficient operation in any industry utilizing sophisticated and expensive equipment on a continuous basis. At today&apos;s large bulk materials handling facilities, the problems of continuous operation of complex machines with their thousands of components exposed to abrasion, dirt, dust and the elements, are intensified and multiplied. Effective preventive maintenance can increase profits. Yet, the number of tasks to be performed is so staggering that it is beyond error-free human capacity. The computer must be an essential ele¬ment in any efficient and economical preventive maintenance system. Computerized preventive maintenance techniques have been successfully used in many fields, usually involving highly skilled and specialized personnel working under favorable and controlled conditions. Now, The Pittsburgh & Conneaut Dock Company has developed and is applying a computerized preventive maintenance system that is applicable to the bulk materials handling industry. The "system" has taken many years of intensive effort to develop and has been time-tested and proven during the past years on equipment handling materials with rugged physical characteristics and corrosive and abrasive qualities, under some of the most adverse weather conditions on the Great Lakes.

Jan 1, 1976

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month&apos;s supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By R. H. Goodman

The development of techniques for separating minerals based on differences in their specific gravities is reviewed and their present applications in process technology outlined. Special emphasis is placed on the development, in Australia, of new models of the spiral concentrator. The mechanics of separation of spiral separators are stated, including the effects of operating parameters, Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes and fine coal recovery.

Jan 1, 1984