Search Documents

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By Robert H. Carpenter

Downstream dispersion curves for certain trace metals were obtained from two mineralized areas in the southeastern U. S. In Lincoln Co., Georgia, 7 sample sets were collected downstream from the Magruder mine, a polymetallic sulfide deposit (Zn-Cu-Pb-Ag-Au) in metavolcanic rocks. Five sample sets were collected along Joe Mill Creek in Grainger Go., Tennessee, downstream from a zone of zinc mineralization in carbonate rocks (Mississippi Valley-type). In both areas, analyses were made of Fe-Mn oxide coatings on lithic fragments and quartz pebbles, and the -80 mesh fraction of the stream sediment. A comparison of the dispersion curves reveals the following: 1.) the anomaly/background ratio is markedly higher in the Fe-Mn oxide coatings for zinc and copper; 2.) the anomaly/background ratlo is markedly higher in the -80 mesh fraction for lead which is not concentrated in the coatings; and, 3.) the Zn/Mn and Cu/Mn ratios in the coatings are useful in that they enhance downstream derectability of mineralization as well as provide for a simpler analytical procedure. There are several potential advantages of using coatings vs. the conventional -80 mesh fraction in stream sediment surveys. Because soluble metal is brought into the stream mainly in groundwater, deeper anomaly sources may be detectable from the oxide coatings than from clastic fractions of alluvium where much of the metal is derived from erosion of soils. Variability due to sampling may also be reduced, providing better discrimination of anomalies. In areas of glacial or alluvial cover, coating surveys may be particularly applicable.

Jan 1, 1975

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Ashis Bhattacherjee, Subrata Chatterjee, Michael T. Dewey, Christopher J. Bise

In order to continue the advancements made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, closer attention will have to be paid to the increasing number of accidents resulting in disabling injuries and lost time. With the increased emphasis on safety training reflected in the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 96-1641, and on MSHA's current focus on the application of Job Safety Analysis, it appears that the acquisition, evaluation, and application of accident and incident data will take on an even greater importance. To manage this large amount of information will require a significant commitment of time and attention on the part of mine training departments. A USBM-sponsored research project is currently being completed at Penn State which focuser on the development of a model training program for mining. The program is based on five distinct steps which represent the coupling of a needs assessment with the program implementation. The five steps are: 1) database analysis, 2) workplace observations, 3) identification of trainable problem areas, 4) a library of training resources, and 6) the implementation of the program. In each of these areas, the microcomputer has proven to be a valuable tool for collecting, analyzing, and presenting accident and incident information. This paper will detail the manner in which microcomputers have been fully integrated into the model training program. Examples of applications at existing mines will also be discussed.

Jan 1, 1992

Vancouver-based War Eagle Mining Co. is an advanced-stage Canadian junior mining company that is focused on becoming one of the world?s leading germanium producers. War Eagle?s primary focus is on the Tres Marias high-grade germanium mine near Chihuahua, Mexico. The Tres Marias Mine has high-grade zinc mineralization as well. War Eagle acquired the 28-km2 (17.4-sq mile) property in 2001 from Tombstone Exploration and is currently working to put the mine into production. Current exploration is focused on supporting a resource report and prefeasibility study that is expected to be completed in early 2008. War Eagle expects to have completed an estimated 80 underground diamond drill holes, 40 surface diamond drillholes, 31 percussion holes and 1,296 1.5-m (5-ft) channel samples. Eighty-seven additional exploration targets have been identified within the mining concession. Recent drill results have significantly expanded the known mineralized body at the Tres Marias Mine. The exploration and development program is expected to be completed during 2008. War Eagle owns both the drills currently in operation at Tres Marias. An advanced exploration and development program has confirmed historical grades and is producing encouraging new results from diamond and percussion drilling, channel sampling and high-resolution resistivity geophysics. Glenn R. O?Gorman, an independent geologist and consultant to War Eagle, conducted a study on the reporter. He stated that the Tres Marias concession area has the potential to host 5 to 10 Mt (5.5 to 11 million st) of minable ore.

Jan 1, 2008

By T. P. Lim, A. J. Vivyurka, N. K. Davé

Chemical and radioisotope stratification studies were carried out in an abandoned uranium tailings pile at Elliot Lake, Ontario, Canada. The tailings, with an average thickness of 7 m over an area of 16 hectares, were deposited approximately 20 years ago on a layer of black peaty material which overlays deposits of permeable glaciofluvial sands. Geohydro-chemical investigations of this tailings area have been ongoing since 1978. The radioisotope profile study was conducted on three adjacent sites. Solid core samples, collected with a split spoon sampler at various depths, were analyzed for various chemical and radioisotope constituents. The results indicated by 2 distinct zones of stratification; an upper zone, where the constituents were uniformly distributed, and a lower zone, near the peat-tailing interface, which showed increasing concentration with depth. Within the peat layer, the concentration decreased rapidly with no significant levels of contaminant penetration below the peat layers observed, though the samples were limited. The pH profile showed that the top 5 m of the tailings have been oxidized, the average soil pH in this zone was 3.4 compared to 5 .8 underneath it. The groundwater hydrology of the system was observed to be complex showing downward and lateral flow in the dry season and lateral and upward flow during the spring and periods of heavy rainfall. The results are discussed in terms of a model based on the combined segregation and settling process of the tailings fine fraction, and the geohydro-chemical interaction of the solid and liquid phases.

Jan 1, 1981

By L. Xu, N. I. Jayaraman, R. Bhaskar

The objective of this study is to develop a better understanding of the collection characteristics of dust measurement instruments used in mine dust control research with respect to properties of quartz and coal dust. Coal and quartz dust of narrow sues, with aerodynamic median diameters being approximately 2 µm, 4 µm and 10 µm, with quartz contents of l0%, 20%, 30%, 40% and 50%, were released in an aerosol characterization chamber using a fluidized bed aerosol generator. Dust was collected in MSA personal gravimetric samplers with l0-mm nylon cyclones, total dust samplers and Sierra 298 inertial cascade impactors. The samples were analyzed for mass and quartz content. A total of 21 experiments were performed for this study. The mass and quartz collection efficiencies of the total and respirable dust samplers and the impactor were determined. The data show that the amount of dust collected by the respirable dust sampler (respirable + oversize dust trapped in the cyclone pre-classifier) was, in general, less than the amount collected by the total dust sampler. The amount of dust collected by the impactor was higher than that collected by the total dust sampler. Quartz analyses of the airborne dust samples showed that the total dust and respirable dust samplers (including oversize dust) collect less quartz dust than at inertial impactor. The larger the median particle sire of the quartz and coal mixture, the lower the quart content of the dust collected in the samplers. For all three sires, the impactor was a better collector of quartz than the other instruments.

Jan 1, 1994

By Tugba Kami?oglu

Hydromagnesite (Mg5(CO3).(OH)2.4H20), one of the sedimentary deposits in Salda Lake Basin, is developed under the control of active tectonics regime. Since the occurrence and deposition mechanism of hydromagnesite are unstable under atmospheric conditions, in order to evaluate the precipitation process, systematic host rock, lake water (surface, 20m, 40m, 60m) and hydromagnesite sampling were carried out. Macro, micro, XRD and chemical investigations were done in detail. Not only the results and formation and crystallization mechanism but also hydromagnesite's St values were evaluated. Main resources could be ultramaficmafic surrounding rocks for hydromagnesite formations. However, hydromagnesite development is considered in different phases, because it has showed various characteristics in Kayadibi and Köpekcayin areas. In Kayadibi area Huntide-Dolomite-Aragonite-Hydromagnesite paragenesis has been realized. Hydromagnesite has also formed in Köpekcayiri area, large amount of hyrdomagnesite occurrences and levels various are noticeable. Actual position of hydromagresite levels exhibits tectonic influences in and around the lake. Therefore, the levels seems to exhibit secondary formation properties. In addition, the formations are being still maintained sedimentation as products of a peripheral deposition phases. Resolving and redifferentiation sedimentation processes probably improve in periods of lake water chemistry especially Ca/Mg proportional changes, and also SI variations indicate the mentioned precipitation mechanism. Similarly, side and into the lake hydromagnesite is stored different levels and ultramafics-mafics rocks fallow indicated stages. It is postulated that hydromagnesite formation, which is existed by result of determined developments and multiphase sedimentation, could be originated from probable crack zones on the lake bottom.

Jan 1, 2005

By R. L. Grayson, N. P. Reddy, D. A. Kinzler, S. Yuan, W. R. Myers, R. A. Wells

An examination was conducted on the impact of roof conditions and the mining cycle in determining a representative respirable mass concentration at the mid-shearer location on a longwall panel. Multiple personal gravimetric dust samplers, operated at a flow rate of 2.0 lpm, were used at different locations along the face to isolate the concentrations and variances associated with good and bad roof conditions under both the cutting and cleaning mode of operation. The number of samples needed to estimate the population variance at a given confidence level was analyzed. In addition, the statistical analysis showed that the coefficient of variation of dust concentrations at different locations and under different conditions ranged from 0.185 to 0.475, with an average value of 0.283. The estimates of the average dust concentration for a shift and the variance of the dust concentrations were calculated. A total of 48 data points were available for an [a x b] factorial ANOVA (analysis of variance). The estimates of the variance components were determined. The results from F-tests indicated that both the roof conditions and mining operations had a significant effect on the respirable dust concentration. There was no significant interaction effect between mining operations and roof conditions. In conclusion, this study shows that not only should sampling and analytical errors be considered in determining the required number of samples for a good estimate of the long-range exposures of miners, but also fluctuations of concentrations due to mining operations and geological conditions should be taken into account.

Jan 1, 1991

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By Ora H. Rostad

The sequence of events preceeding the discovery of the Mount Emmons molybdenite include some inadvertent near misses by several groups. The events are given in general chronological order to bring out the essentially contemporaneous, but different activities by several groups in two areas on opposite sides of Mount Emmons. The Mount Emmons molybdenite deposit lies in the Elk Mountain mining district. The west edge of the deposit is near the boundary between the Elk Mountain and Ruby mining districts as shown by the USGS map included (see Fig. 1). Considerable history regarding the Keystone silver-lead-zinc mine is given because of its proximity to the Mount Emmons molybdenite deposit which is on the other side of the mountain from Redwell Basin and where other significant activities took place. It should be noted that there was no documentary evidence available to me that would indicate that molybdenite was recognized to be present on, or under, any part of Mount Emmons, including Redwell Basin, before 1970. Veins containing silver-lead-zinc minerals were discovered in the Elk Mountain and Ruby mining districts about 1872. Some discoveries on the south flank of Mount Emmons about 1880 were developed into the Keystone mine. The Keystone has the largest cumulative production of metal ores of any of the mines in these districts. Most of the 413 Mt (455,473 st) of ore produced from the Keystone mine through August 1967 was produced after 1950. The ore averaged 175.4 gt (5.64 oz per ton) Ag, 2.62% Pb, 5.56% Zn, and 0.72% Cu.

Jan 1, 1991

By James S. Scott

Effluents discharged from gold mills, and more recently from heap leaching operations, pose significant hazards to the environment if not properly managed prior to discharge. This paper describes the nature of wastewaters which must be treated, the treatment processes being applied in Canada and the capabilities of these methods in removing cyanide and metals. As a result of past practice the most common method of reducing cyanide in gold mill effluents remains that of natural degradation in tailings ponds. This method has proven capable of producing high quality effluents where large ponds and sufficiently long water retention times can be provided, but at many mines this has not been the case. Since 1981, as a result of these limitations there has been a strong move in Canada to chemically-based effluent treatment plants, particularly as additional processes became available. Canadian gold mills have become leaders in the use of chemical processes to remove cyanide, in terms of the variety of such processes in operation (five in total), the number of plant installations and the number of processes developed in this country. The hydrogen peroxide and Inco SO2-air processes, in that order, are being applied most widely. Alkaline chlorination, the initial process to be used fairly extensively has been almost totally replaced by the two methods mentioned above. Since a number of effective methods are now available for the treatment of gold mill effluents, the selection of a process for application at a specific mill requires careful consideration of:

Jan 1, 1987

By John W. Rushton

THE PLANNED MAINTENANCE PROGRAM All concentrators should start with a planned maintenance program from day one. Every- body thinks they have a program in place before start-up, but in reality, most have only a fraction of what is needed to avoid the "Post Start-up Disaster" (PSD) - two years for start-up is not that uncommon. An effective program has all of the following: (1) Good people. (2) Area Maintenance. (3) Good PM Checklists. (4) Daily Work Schedules. (5) Written Work Orders. (6) Equipment Histories. (7) Backlog Control. The installation of a workable program takes hard work, talent, and commitment. You have to know what you are doing (hard work will not replace talent). Good People Good people are available in any location if you make the effort. Always check references carefully (both superiors, peers and subordinates). Was the last concentrator they worked at successful? Was it clean? Find out! Success or failure follows people around. I know people who are experts on PSD because they have lived through it three or four times. You need some college trained people with hands-on experience. There are no secrets, you have to make the effort. If you make a mistake in hiring (and you probably will), make the tough decision necessary to rectify it quickly. Area Maintenance Area maintenance refers to organization of supervision such that one person is uniquely accountable for every inch of ground and piece of equipment. Avoid overlapping authority if at all possible. You must have a planner as a staff position. A foreman cannot effectively plan and

Jan 1, 1986

By Morris Loshinsky, George Ziegler

The New York City Transit System is celebrating its Diamond Jubilee this year. In 1904, 9.3 route miles of New York's first subway was placed in operation in lower Manhattan. Since that date the system has grown to 230 route miles and 458 stations (See Exhibit #1). The age of the system immediately provides a clue to the nature of our construction activity. While we must always plan for the future and expand the system in the direction of the future needs in New York, a substantial amount of time and money must be channeled towards the modernization and maintenance of the existing system which provides vital transportation for 3-1/2 million passengers a day. This paper however will be directed to our New Route's Construction and, specifically, to three rock tunnel and cut and cover sections presently under construction. Currently, New York is engaged in the construction of about 9 New Route miles of structure. Briefly, the 3 Sections we will discuss are as follows: Route 131-A Section 5A is a 4 track structure in Manhattan and includes the new Lexington Avenue Station. This 1240 foot long section is located between Park Avenue and 3rd Avenue and is a combined cut and cover and rock tunnel section under 63rd Street. Route 131-A Section 5B is an intricate 2423 foot long 4 track rock tunnel section extending from 3rd Avenue to the FDR Drive under 63rd Street in Manhattan.

Jan 1, 1979

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986