Search Documents

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By N. Finkelstein, D. A. Hinckfuss

The large and compact but simple Bougainville Copper Limited flotation circuit has been in operation for 3-1/2 years. Discussion of problem areas encountered since start-up and remedies that have been implemented or proposed, form the main basis of this paper. Full cur- rent operational data is also provided.

Jan 1, 1976

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By Haydn H. Murray

Since the advent of machine coated paper in the mid 1930's, the kaolin industry has had a remarkable growth, In 1935 the domestic production of kaolin was 500, 000 tons and in 1970 the estimated production was in excess of 3. 5 million tons. The process industries which use kaolin most extensively are paper, rubber, paint, ceramics, plastics, catalyst manufacturers, ink, and pharmaceutical. The paper industry is by far the largest consumer of kaolin using approximately 70 per cent of the total tonnage mined and beneficiated. Up until 1970 the major kaolin producers were able to expand rapidly enough to supply the demand but for the first time in thirty years the demand is expected to be in excess of mining and beneficiation capacity through at least 1975. The major reason for this is the expansion of coated paper production in Europe and Japan. Two areas supply the lion's share of kaolin for the world markets. These are the Cornwall area in extreme southwestern England and a limited area of Georgia and South Carolina in the southeastern U. S. The English kaolins are primary - (found in decomposed granite) whereas the Georgia-South Carolina kaolins are secondary - (found in lenticular, continuous beds in the Tuscaloosa formation of Cretaceous age. ) The English kaolins are mined by hydraulic methods whereas the Georgia-South Carolina kaolins are mined by dragline or shovel and benefidated by using a wet process for the majority of the production and/or a dry

Jan 1, 1971

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

Introduction The frigid regions of Canada's high arctic islands are well-known for major oil and gas explorations. But mining leads the way in development. Cominco Ltd.'s Polaris mine is in its second full year of commercial production, and outstripping the rated production capacity foreseen by its planners. The Polaris mine is located on the shore of Little Cornwallis Island, near the settlement of Resolute Bay. The mine property is compact. It occupies about 3 km2 (0.5 sq miles) of the vast Arctic landscape. A number of mining and technological firsts were necessary to bring a mine into production at this 76° North latitude. Development constraints that had to be overcome included climate, remote location, and the limited ice-free shipping season. Construction of the entire process plant and ancillary facilities took place on a barge in the South where labor and supplies are plentiful. The plant was towed through ice-strewn waters to its permanent location at the mine site 1450 km (900 miles) from the North Pole. Freighters moved the first shipments to the South during ice break-up in late summer 1982. Most of the zinc concentrate is sold to European smelters. The remainder is tolled at a custom smelter in Europe, and the resulting metal is sold by Cominco. Lead concentrate is sold to European smelters. The mine was designed to produce 177 kt/a (195,000 stpy) of zinc concentrate and 41 kt/a (45,000 stpy) of lead concentrate. Actual production in 1983 was considerably greater, with both mill throughput and feed grades being higher than forecast. Production was 217 kt (239,300 st) of zinc concentrate and 51 kt (56,300 st) of lead concentrate. Average milling rate was 2.3 kt/d (2500 stpd), well above the designed capacity of 2.1 kt/d of (2300 stpd). Arctic Climate Extremes The climate is typical of the Arctic: very dry with short, cool summers and long, cold winters. From November through February, there is continuous darkness. Continuous daylight prevails from April to August. Precipitation is light, rivaling the Sahara desert at about 127 mm (5 in.) of rain and snow a year. An almost continual wind forms deep snow drifts against any obstacle on the ground. Temperatures range from a winter low of about -50°C (-58°F) to a relatively pleasant 15°C (59°F) during sunny days in August. Freeze-up begins in September and ice thickness increases from less than 0.3 m (1 ft) in early October to a maximum of about 2.1 m (7 ft) in May. The permanently frozen ground extends to a depth of about 427 m (1400 ft). Only a few inches of surface ground thaws in the summer. Exploration Activity Zinc-lead mineralization was

Jan 10, 1984

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018