Search Documents

By W. R. Reed

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

Jan 1, 2008

By P. D. Nora, M. G. Ranade

A statistically designed pot grate-kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables - bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate - were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a plant trial. The target firing temperature at the Empire plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets.

Jan 1, 1987

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

By S. R. Maynard

The Ortiz Mountains lie 25 mi (40 km) northeast of Albuquerque, New Mexico in Santa Fe County (Figure 1). Approximately 350,000 ounces (11,000 kgs) of gold have been produced from the Ortiz Mountains since the 1820s. The 100 square mile (260 square km) Ortiz Mine Grant was secured from the Mexican government in 1833 by Jose Francisco Ortiz for the purpose of mining gold. The Grant has remained more or less intact to the present. The mineral rights are currently owned by Ortiz Mines, Inc. of Joplin, Missouri and are leased to LAC Minerals, USA, Inc. (west half) and to Gold Fields Mining Corporation (east half).

Jan 1, 1989

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By R. E. Nivens

In the past, Newmont Gold Company relied on cement for their ore agglomeration process. With assistance from Betz Industrial, Newmont began Investigating the use of polymers for ore agglomeration. If gold recovery would not be jeopardized, then polymers could replace cement and possibly reduce operational costs associated with cement agglomeration. The following outlines the preliminary testing conducted to determine the feasibility of polymer agglomeration with Newmont's ore and the results of the test heap, which was constructed so the program could be examined under actual operating conditions. Similar polymer agglomeration testing has been successfully performed in other Nevada gold operations. By eliminating the need for cement, a polymeric agglomeration program could improve material handling operations, as well as offer the following additional savings. First, the polymer application uses only lime for adjusting basicity, the polymer does not contribute any alkalinity to the heap. Because lime is more soluble than cement, detoxification of the heap becomes much faster and less costly for the mine relative to rinsing cement alkalinity. The following graph compares the detoxification rate of cement and polymer over a 33 day cycle.

Jan 1, 1993

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By S. B. Castor

Proceeds from industrial mineral mining in Nevada were approximately equal to those from metal mining during the barite boom in the late 1970s and early 1980s; however, since then the economic importance of industrial minerals has been overshadowed by gold mining (Fig. 1). The total value of industrial minerals mined in Nevada increased by about 60% during the 1980s, reaching an estimated $306 million in 1990 before falling slightly in 1991. The state's most important industrial mineral commodities, in order of estimated value, are aggregate, lithium carbonate, diatomite, lime, cement, gypsum, barite, clay, silica, and magnesia (Fig. 2). Industrial minerals produced on a smaller scale are colemanite, dimension stone, dolomite, perlite, salt, and zeolite. In 1991 industrial mineral commodities other than aggregate were produced at 39 operations in Nevada. Most of these operations are located near the two major metropolitan areas of the state, or along the major transportation routes (Fig. 3).

Jan 1, 1993

By J. E. Shearer

The state of Arizona produced 253,276.2 metric tons (279,000 st) of crude gypsum during 1986. This represents approximately 1.7% of the total U.S. production. Four mines provided Arizona's gypsum, three of these mines are in the San Pedro Valley. The uses of the gypsum produced in Arizona are for manufacture of cement, agricultural uses, and wallboard manufacture. The gypsum is used as a retarder in the manufacture of Portland cement. The use in agriculture is treatment of alkali soils to allow water penetration. Other deposits in the San Pedro Valley have production potential, providing there is sufficient market for additional wallboard. The author completed an evaluation of one property earlier this year.

Jan 1, 1988

By Jacek Galas, Stanislaw Lenczowski

The image of the flotation froth surface in the mineral processing plant contains the information about its composition. This information can be very useful for a technological process automation. Images, captured in the optical part of the measurement system were read by the computer, then were transformed and analysed digitally. The set of image parameters, extracted from an image transforms, was evaluated by statistical analysis. The recognition algorithm constructed in this process allowed to estimate the froth composition.

Jan 1, 1995

By Clarice L. Amaral, Ricardo Melamed

Clay-coating has been used as an environmental technology tool for the immobilization of toxic elements. The mechanisms of arsenate retention in clays suggest that not only the system pH is of fundamental importance in the process but also the character of metals and ligands that compose the electrolyte system. The goal of this study was to investigate the interactions between system pH and electrolyte ions on the retention of arsenate in an Oxisol soil. The sorption of arsenate decreases with the increase in system pH, reflecting the competitive sorption of arsenate with OH groups. Solutions containing Ca tend to favour the immobilization of arsenate in a relatively broad pH range.

Jan 1, 1998

By L. Sandbak

A geomechanical rock mass classification or RMR is currently being used for the evaluation of an LHD mechanized mining system versus the conventional block caving method. The successes and failures of a Panel lS-19 LHD test block on the 2315 level can be attributed to the geologic and geomechanical zonation present. Trench blasting, caving procedures, and sequencing are other factors that were also considered. Lessons learned from the P.lS-19 test block have been used to alter the design for future LHD production blocks on the 2615 level. These modifications are designed to maximize the pillar and insure an adequate draw connection.

Jan 1, 1988

By Frederick W. Bauer

The potential worldwide "market" for metallurgical bauxite is about 94 million MT. The high degree of concentration of the alumina sector, combined with the high percentage of long-term contractual relationships, results in a small spot market with an illdefined price structure. Further segmentation occurs based on bauxite quality and alumina plant design. The potential 'free" market is estimated to be about 18 million MT that represent the requirements of nonintegrated alumina producers. It, too, is covered almost entirely by multi-year supply contracts.

Jan 1, 1984

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

By Key Rosebrook, Jennifer Laggan, Ashley Rivera

Significant quantities of waste rock at abandoned uranium mine (AUM) sites in the western United States require removal from steep slopes exceeding 45 degrees in remote locations. This prevents the use of traditional excavation equipment and poses significant challenges for safe, effective material removal. A pilot study was conducted using a spider excavator to demonstrate the feasibility of removing waste rock and transporting it to areas where conventional equipment could be employed. The spider excavator was evaluated for its effectiveness in excavation, material movement and control, container usage, dust mitigation, and ensuring human health and environmental safety. The study established constructability and engineering parameters for implementing spider excavators in these challenging environments. Key outcomes include the preservation of existing vegetation, improved waste movement control, and enhanced safety measures for workers, nearby residents, and the environment.

Feb 1, 2025

By G. J. Goldberg

Through the early 1980's, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation of total station systems and their ability to meet the surveying requirements of Bingham Canyon culminated in the purchase of a total station system as the mine re-opened in 1986. This paper presents the procedure for evaluating, implementing and using the total station survey system at Bingham Canyon.

Jan 1, 1990

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By PDF

The adsorption of ethoxylated sulfonates and nonionics of the same ethoxylation number?on a low-ash coal has been studied. The surfactant adsorption has been investigated as a function of concentration, pH, temperature and ionic strength for three homologues. Zeta potential of coal particles and surface tension of supernatants has been concurrently determined to eludicate the orientation of sudactant molecules on the coal surface as well as the mechanism of adsorption process. The adsorption data are utilized to calculate thermodynamic parameters such as the free energy of adsorption and isoteric heats of adsorption.

Jan 1, 1988

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988