Search Documents

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By Lyle A. Hale

The subject area known as upper Dry Valley is located 15 miles due east of Soda Springs in Sections 14 and 23, Township 9 South, Range 44 East, Caribou County, Idaho. The railroad extending from Soda Springs to its terminus at El Paso's Maybe Canyon mine is 8z miles to the north in lower Dry Valley. Initial data derived from trench work in 1962 revealed a variety of econom¬ically significant alterations of the phosphatic beds related to the rather unique geomorphic development in the northern part of phosphate lease 1-012989. It was apparent that such conditions, while valid for near-surface beds in a strike direction, would be misleading if projected to the proposed depth limits of strip mining. Consequently, a subsurface mapping program was initiated in 1963 to determine: (1) the depth and horizontal extent of weathering and related phe¬nomena, (2) the depth, thickness, and quality of ore beds and intervening strata, and (3) structural geology as a guide for mining procedures. Successful use of a scintillometer in 1956 to detect the subcrop position of phosphate beds in the Smokey Canyon area of southeastern Idaho led to the conclusion that gamma radiation surveys of drill holes could be a useful aid in subsurface mapping. The objectives of this paper are: (1) briefly to describe geologic features characteristic of the phosphate lease area and (2) to demonstrate the practical application and theory behind gamma radiation logging as an effective tool in the economic evaluation of a phosphate lease.

Jan 1, 1969

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By G. C. Allen

Selective flocculation is used for the purification of clay minerals. Here we present data from a surface spectroscopic investigation into the polyacrylamides mediated selective flocculation of kaolin from an impure matrix. Use of X-ray photoelectron spectroscopy (XPS) was shown to offer a useful approach for investigating the observed selective separations. In particular, a new small area XPS technique was used to characterize, in situ, the differential competitive, f1occulant adsorption onto mixed kaolin/gangue systems.

Jan 1, 1998

By Thomas A. Simpson

Hydrogeological techniques were used to solve problems of slope stability in open-pit mines of the Eufaula bauxite district, Alabama. Geologic and hydrologic data were evaluated and used to design a system of dewatering wells to enable the operators to mine bauxite more efficiently and economically. Walls of open-pit mines in the district were subsequently stabilized by the operation of the dewatering system. Three open-pit mines, each at varying stages of the mining process, of the A. P. Green Refractories Company, were used to develop a sequential series of guidelines that indicate how to effectively remove ground water from the formations surrounding the ore bodies in the district. The use of sound engineering principles in well design, in combination with the correct interpretation of the pit hydrology provided the basis for solutions of the slope- stabilization problem aided in the economical removal of bauxite from mines of the district.

Jan 1, 1975

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but not obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O&apos;okiep Mining Company in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1969

By C. J. Im

As market conditions become more competitive, U.S. coal producers are faced with the increasing need to find methods of lowering production costs in their operations. One area worthy of investigation is the additional recovery of fine coal that is normally discarded in the preparation plant waste stream. United Coal Company is currently assessing the capability of the Deister Flotaire, a new application of a column flotation cell, to recover additional, saleable coal from preparation plant waste. This paper presents the technical data obtained to date. Work with a 0.76 m (30 inch) diameter cell installed in a plant shows considerable coal recovery is possible from a nominal 0.595 run (28 mesh) X 0 refuse stream.

Jan 1, 1986

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By Elif Emil-Kaya, Bernd Friedrich, Merve Papakci

Samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are used in the production of SmCo permanent magnets, which have excellent temperature stability, corrosion resistance and oxidation resistance. Of the two types of SmCo magnets, one contains a high amount of iron, approximately 15.2 percent. This paper focuses on the recycling of iron (Fe)-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Jul 1, 2024

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By B. S. Hulvey

Thin support liners are becoming more accepted and being developed with improved properties because the mining industry as a whole has been offering underground safe test trial sites. This is because of the huge potential for such products. Recent developments tend to indicate that the technology is “coming of age” and these are discussed in this paper.

Jan 1, 2003