Search Documents

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or 'greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By C. H. Lee

The world-famous Sang Dong Mine in the Republic of Korea has long been one of the world's greatest tungsten ore deposits. Over the years, the development of the Sang Dong deposit has steadily increased to a point where it now exerts a great influence on the world tungsten market. The mine is located in the mountains of the province of Kang Won Do, approximately 150 miles by road due east of Seoul, the capital of the Republic of Korea. In recent years the transportation system in Korea has greatly improved and the mine is now serviced by an excellent secondary type road from the new railroad line which is 20 miles away. The Sang Dong operation is made up of the underground mining, beneficiation mill, chemical refinery, tungsten metal plant, bismuth refinery, acid plant, foundry and machine shops. The bismuthinite production from the Sang Dong Mine is also of considerable importance, The output accounts for nearly 10 per cent of the world production of bismuth. A small amount of molybdenite concentrate is also recovered from the flotation operation.

Jan 1, 1962

By M. R. Peterson

The U.S. Bureau of Mines (USBM) is investigating alternative methods to strip metal-loaded solvent extractants. Hydrolytic, precipitation, and hydrogen pressure stripping all recover metal or metal salts directly from the organic solvent extractant. Pure metals, metallic oxides, or metal salts can be formed, allowing direct production of value-added products. Aspects affecting commercial application are emphasized, including metal recovery from actual ore leach solutions, particle size control, organic modifier and diluent effects on stripping and metal recovery efficiencies, metal grade, seed addition, mixing intensity, recycling efficiency, and reactor plating. Metal separations from copper ore leach solutions and complex waste leach solutions were examined.

Jan 1, 1995

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By J. J. Sense

The Mission Unit of American Smelting and 'Refining Company is located in Pima County, Arizona, approximately twenty miles southwest of the City of Tucson. The Unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to Company Smelters at Hayden, Arizona, or El Paso, Texas Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tons per day concentrator gas started in the spring of 1960, The first ore was treated in mid summer of 1961 and full ore production was reached in August of 1961. At that time over 46,000,000 tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tons per day. Total production to date (ore and waste) over 120,000,000 tons.

Jan 1, 1964

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By Eugene W. Price

One of the most important fundamental characteristics of iron ore pellets is their porosity. This importance arises from the fact that the pores are the busy avenues whereby many changes are brought about in the life and form of the pellet from the time it is made until the iron it contains emerges as a molten stream from the blast furnace. As a green iron ore pellet is first heated in the drying cycle of a typical heat-hardening process, the pores act as conduits to allow the escape of steam from the water or vapor from the oil which served as binders to hold the green pellet together. After the release of the steam (or oil vapor) the pores then act as conduits whereby oxygen can enter the pellets to 1) convert magnetite (Fe304) to hematite (Fe203), if appropriate, and 2) promote solid state grain growth between adjacent particles of iron ore. The rate of oxidation and the rate of grain growth are directly related to pore size' and pore size distribution. Rate of oxidation is also directly influenced by length of pore and length of pore is obviously related to pellet diameter. It is well to keep in mind that the heat-hardening process does not harden the mineral grains themselves. What it does is weld them together to change the green pellet from a doughy mass, composed of thousands of tiny individual particles, into a strong, intergrown monolithic structure. In the blast furnace the pores again act as conduits for gases, but in this case they trans¬port reductants such as hydrogen (H2) and carbon monoxide (C0) which remove most of the oxygen from the ore. Rate of reduction is also directly related to pore size and pore size distribution.

Jan 1, 1967

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By Louis J. Czel

Although lithium was first discovered by Arfwedson in Sweden in 1817, it did not reach any significant status in commercial application until 1908 when Thomas A. Edison received a patent covering the use of lithium hydroxide in alkaline' storage batteries. Edison's achievement can be regarded as a major breakthrough in the development of the lithium industry. In the years prior to 1908 lithium salts had found only modest applications in the pharmaceutical and pyrotechnic fields. The next important milestone in the growth of this net industry occurred in Germany in 1918 when Metallgesellschaft at its metallurgical laboratory at Frankfort-on-Main discovered that the addition of a few hundredths percent of lithium metal to aluminum and its alloys increased-the hardness. This brought into being a new commercial use of lithium in the manufacture of bearing metals. The new material, called "Bahnmetall" (railroad, metal), was widely used for, many years in the manufacture of bearings for railroad and automotive purposes. Its use continued until the early 1930's and there was a short-lived renewal of its production during World War II. Subsequent use of-the alloy was soon outmoded.

Jan 1, 1961

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980