Search Documents

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By J. W. Leonard, D. A. Newman

Discussion by N. Standish and P.N. Standish Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage-"the bottom line evaluator." Correct. Theory Definitions Coal bulk density is the ratio of the mass of a collection of discrete particles to the volume that it occupies (ASA, 1980). There can be no possible argument about this definition. Mass and volume are readily measured both in laboratory and large scale installations. So, to obtain the bulk density, one simply divides the measured mass by the measured volume. It is here that we come unstuck as everybody who has ever had to reconcile book values with the measured stock tonnages knows. Where does the problem originate? Almost invariably in a too casual a reading of the above definition and the words "a collection of discrete particles." The word collection means "a number of objects collected or gathered together, viewed as a whole" (The Oxford English Dictionary, 1989). If one knows the bulk density of a pile of coal viewed as a whole,

Jan 1, 1991

By Warnie Flint

According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. No one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and. the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, but not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By R. J. Cornelius

Gold with minor associated copper mineralization in the area of what is now the Bougainville porphyry copper deposit has been known since the 1920s and was probably known in German colonial times, pre- 19 14, although no records persist other than a reference by Stanley (1922) to copper specimens from Kieta that he saw in Rabaul. Stanley did not at the time believe that they came from Kieta. Gold was first discovered at Kupei by Jack Comb in 1929 and the Kieta Goldfield was proclaimed in May 1930. In December 1932, the Tapu Reward Claim at Moroni - the site of the Bougainville Copper concentrator, was pegged by C.W.M. Evans who prospected up river from the West Coast. The Pumkuna (Panguna) Reward Claim on the site of the subsequent porphyry copper deposit was granted in February 1934 to G.A. Myers. n May 193 1, the Kupei Reward Claim was transferred to Bou- gainville Gold Options NL and later reverted to Jack Comb and then the Bougainville Syndicate, as did the Pumkuna and Moroni claims. Most of the interested parties had come from the Edie Creek rush on the New Guinea mainland. In 1935, N.H. Fisher, the geologist in Rabaul for the New Guinea administration who later became director of the Australian Bureau of Mineral Resources in Canberra, reported on the three gold areas. Norm Fisher described the gold and copper mineralization and its habit in great detail and this report had a major influence on the events leading to the discovery in the 1960s. Gold production up to the Japanese invasion probably did not exceed $50,000 in value. Half a ton of copper-gold ore from Kupei was sent to O.T. Lempriere's in Sydney for assay in the early 1930s.

Jan 1, 1991

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By Kenneth G. Knight, Frank L. Lynch

It's 12:30 A.M. The day before had been a long one with problems ranging from proper application of shotcrete during cold weather and the follow-on precautions for curing, meetings with city officials to avert a job shutdown because traffic wasn't being maintained properly and finally a briefing before METRO's General Manager to bring him up to date on projections for meeting the operational date of June 1975. The phone rings and Officer Jones of the Park Police says "Mr. Lynch, this lady in the apartments overlooking the jobsite is complaining of noise and she wants the job shutdown". "Officer Jones, have you called the Project Manager or the Resident Engineer?" "Yes, sir, but there is no answer!" "O.K., Officer, I'll check it out." In calling the job, I can only get the guard, because the inspector is in the tunnel. After some time, the guard calls back and says he doesn't know the way down into the tunnel. I have since had a difficult time believing that one. In the interim I finally reached the Resident Engineer and explained the situation. And finally at 1:30 A.M. the inspector called the Resident to say that the Park Police stopped the job at 1:00 A.M. because we didn't respond promptly. A similar situation had occurred some 2 years previously. With great expectation, noise specifications were developed to correct the earlier situation that had occurred. These newly developed specifications were in force at the time of this most recent shutdown. Common sense would tell you that even though we had developed and implemented, we believe, some of the best and most practical noise specifications in construction practice today, we had not enforced them. What caused the shutdown - a noisy

Jan 1, 1974

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By G. L. Black

Choosing a mining method for an underground ore body is a complicated and often iterative process. Advances in technology give the design team an overwhelming array of possibilities for methods and equipment. Hecla's recent discovery of the deep Gold Hunter ore body has given the staff at the Lucky Friday Mine the exciting challenge of determining the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization, including drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of information as the project progresses through exploration and development.

Jan 1, 1998

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By John H. Canterford

The conversion of nickel and cobalt to the water-soluble sulphates forms the basis of some of the many methods of recovering these metals from their oxide and silicate ores. The applicability of these sulphation processes to a range of Australian oxidized ores is discussed. The chemical and hence mineralogical composition of the ores is shown to have a major influence on the degree of nickel and cobalt extraction. Different sulphation processes are compared, taking into account the influence of ore composition, and considering effects on reagent consumption and on subsequent metal recovery processes.

Jan 1, 1979

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

By M. J. Laurila

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of on-line analyzers (ISO/DIS 15239).

Jan 1, 1999

By Mahmoud Sepehrmanesh, Verya Nasri

The purpose of this paper is to outline the advantages and disadvantages of single tube and twin tubes for subway systems. Different aspects such as diameter of the tunnel (tunnel spaceproofing), configuration of subway line and stations, impacts on passenger safety and evacuation, ventilation system as well as rail system for each solution were evaluated and compared. In addition, a multi-criterion approach is established to facilitate the decision making for these two different subway systems. The practical example of a mega project has been discussed and the details of the decision-making process has been explained. This proposed multicriterion can be used to facilitate selecting the best subway system in any urban areas.

Dec 1, 2022

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline?s long-term performances and availabilities, to develop preventive maintenance plans, and to make future projections about the machine?s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, PAGE 736 and MARION 7820, which have been operating in Tunçbilek open cast coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages as: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data; (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (20 yd3) is seemed to be more reliable and less likely to fail when compared with Marion 7820 (40 yd3). The operating hours without failure range from 41 to 51 hours with 50 percent reliability.

Jan 1, 2011