Search Documents

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By Mohamed A. Younis, Robert J. F. Goodfellow

This paper investigates the design approaches taken and the philosophy employed during the construction of the Metropolitan Airport Commission (MAC) storm tunnels, part of the Phase 4 Segment of the MAC Trunk Storm Sewer Project at Minneapolis St.-Paul International Airport, located in Minneapolis, Minnesota. URS Corporation was retained to provide a design and Construction Management (CM)services for the MAC Trunk Storm Sewer Project. A case history of the design and construction challenges of the project is presented. The MAC storm tunnels consisted of the construction of twin 10-foot inside diameter (I.D.) tunnels within 7 feet of an existing 72-inch I.D. storm pipe at the base of a 70-foot high highway embankment. The analysis required during the design stage of the project is discussed. This analysis and our design approach provided a defensible framework and justification to make design decisions on relevant issues including: allowable spacing of new and existing structures; preferred order of construction; expected ground deformation behavior; response of lining types to adjacent construction; and effects of proposed changes to design at the submittal stage and during construction.

Jan 1, 2003

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970's prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By S. R. Titley

Results of regional analyses of precious metal habits in Arizona ores lead to interpretations of a fundamental ore control related to geographic location that corresponds with crustal contrasts. Measurements of isotopic and trace element characteristics of Laramide ore-related intrusions lead to interpretations of crustal derivation of apparent ore-related magmas. Interpreted regionally, the numerous kinds of Laramide ores, which include porphyry copper deposits of this southern cordilleran region appear to be phenomena of a specific crustal lithology characterized by a basement of Proterozoic turbidites and (an interpreted) lower crust of amphibolite. This association with a specific basement terrane may be extended in principle from the United states into Mexico where faulted offsets of this basement are similarly favorable to formation of Laramide porphyry ores -to the exclusion of adjacent terranes. Whereas plate tectonic mechanisms may have triggered evolution of these ores, it is hypothesized here that crustal setting and crustal composition are more profound influences of metallogenesis.

Jan 1, 1992

By T. B. Thompson

The Leadville District has been a prominent metal producer since its discovery in 1860. Veins and replacement bodies both have contributed to district production. The latter have been the major metal sources and are hosted within the Paleozoic Leadville, Dyer, and Manitou Dolomites. Igneous bodies representing eight separate events cut the sedimentary section. The main intrusive complex within the district occurs in the Breece Hill area and was the thermal center about which the vein and replacement ores exhibit mineralogical zoning. Precious metal-pyrite-quartz veins (quartz Th= 422 to 469°C; salinity < 4.2 wt. percent eNaCI) occur within or peripheral to the Breece Hill Intrusive Complex, whereas base metal veins and replacement bodies extend from the complex margins outward as much as 2 mi. Pre-ore and post-ore igneous bodies occur, but Fragmental Porphyry dikes immediately post-date the ore event. The Fragmental Porphyry grades downward from a heterolithic breccia with rock-flour matrix to one with a dark, glassy, sulfide- and phenocryst-bearing matrix, commonly with quartz-feldspar porphyry selvages on the dike. Two types of replacement bodies are recognized in the district: 1) the Leadville-type (LTM), massive sulfide (> 60% sulfides) bodies with recoverable Zn, Pb, Ag, and Au, and 2) the Sherman-type (STM), sulfide bodies (low total sulfide) with barite, galena, sphalerite, argentian tetra.hedrite, and minor pyrite. The latter type occurs only within the Leadville Dolomite and is found throughout the Mosquito Range and extending into the Alma District. The Leadville-type replacement bodies are zoned with a pyritic margin and base metal core. Wallrock alteration and trace Pb-Zn dispersion are strongly developed in igneous wallrocks but are weakly developed in carbonate wallrocks. Cu:Zn, Ag:Zn, and Au:Fe ratios increase outward from the center to the margins of LTM. Some of the sulfide bodies are localized on earlier-formed magnetite skarns. Pyrrhotite, pyrite, and marcasite are the earliest formed sulfide phases while chalcopyrite, marmatite, and galena developed later. Tetrahedrite and electrum occur in vugs and fine veinlets cutting the sulfides. Late-stage barite, dolomite, and fluorite occur as minor phases. Pressure-corrected Th for quartz (375-410°C), sphalerite (374-387°C), barite (320-360°C), and dolomite (310-314°C) fluid inclusions with salinities < 5.2 wt. percent eNaCI characterize the fluid responsible for the formation of the Leadville-type orebodies. These values clearly demonstrate the high temperature and low salinity of the ore fluids. Sulfur isotope analyses for galena and barite from LTM are - 1.9 to + 0.9%o and 7.8%o, respectively. Proximity to feeder veins and favorable dolomite hosts are the principal controls on ore localization. The Sherman-type bodies are not internally zoned but commonly have host rock silicification near the orebody margin or in the footwall rocks adjacent to fluid flowpaths along faults. Early quartz, pyrite, dolomite, and white barite precede base metal-silver minerals which are followed by late quartz and golden barite. It is not clear whether the early quartz and the late quartz and barite are part of the STM-forming process. Fluid inclusion analyses yield trapping temperatures as follows: early quartz, 316-341 °C; barite, 264-347°C; low-iron sphalerite, 215-265°C; and late quartz, 260-278°C. All inclusion fluids have salinities < 8.1 wt. percent eNaCI. Sulfur isotope values for barite and galena from STM range from 13.2 to 24.00/00 (avg: 18.4%o) and -6.8 to -3.8%o (avg: -5.5o/00), respectively. A hydrothermal fluid d34SSS of about 15%o is needed in order for galena and barite in equilibrium to exhibit the observed sulfur isotope compositions. Equilibrium sulfur isotope fractionation between barite and galena indicates a 300°C temperature of deposition. Two separate hydrothermal events appear to have taken place to form the distinctive Leadville-type orebodies and those of the Sherman-type assemblage. The STM is known to be older than the LTM. The latter is likely mid-Tertiary in age, post-dating emplacement of the Johnson Gulch Porphyry. LTM is clearly related to meteoric leaching of sulfur and lead (and other metals) from the upper portions of the Breece Hill Stock. Fluids were transmitted along faults, bedding planes, and contacts, and cooled away from the intrusive complex. Early ore fluids were weakly acidic and developed argillic assemblages in the igneous rocks adjacent to the fluid conduits. Reaction/replacement of carbonate rocks occurred where fluids encountered dolomite, but rapid neutralization prevented any wide-spread alteration beyond the ore-carbonate host contact. Pressures based on sphalerite geobarometry and stratigraphic reconstruction were 1.0-1.2 Kb. The high temperatures of vein and replacement ore fluids indicate that chloride complexing was more effective in metal transport than bisulfide complexes. Cooling, dilution of ore fluids, and reaction with carbonate rocks were the major factors in LTM ore deposition. STM formed over wide expanses of the Leadville Dolomite terrain adjacent to (and possibly capping) the Sawatch uplift. Sedimentary sulfur was derived from Pennsylvanian evaporite-bearing sequences adjacent to the uplift. Ore leads are strongly radiogenic (J-type) and are compatible with a crustal-leaching model. Temperatures of ore formation are higher, and ore-fluid salinities are lower than Mississippi Valley-type ore fluids. Superimposed upon dark-gray, diagenetic Leadville Dolomite are several stages of hydrothermal dolomite regionally distributed astride intrusive centers of the Colorado Mineral Belt. The presence of these later dolomites argues for dolomitization and later ore deposition in response to an abnormal thermal gradient caused by emplacement of Laramide batholiths and their generation of convective flow of meteoric fluids.

Jan 1, 2013

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By John J. Dran

[This paper summarizes the more popular mineral valuation techniques being used by the dining industry, and attempts to demonstrate how they are Interrelated and where some are in error when compared to modern methods of financial analysis. The academic community and the larger and more sophisticated raining companies, have largely rejected the older valuation methods such as the, Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or ?safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest In numerous (often non-mining} alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice, all mitigate against the continued use of the older valuation methods, especially for the larger mining companies. Snail mining companies and Individuals still use these methods largely out of habit and familiarity. This paper attempts to point out the weaknesses and strengths of the valuation methods In current use in the hope that these techniques may be better understood and [rcrn] appropriately applied.]

Jan 1, 1973

By C. J. Bise, P. Bucks

Central Appalachian coal reserves are a valuable natural resource in high demand, both domestically and internationally, justifying efforts to increase percentage recovery through pillaring. Unfortunately, the challenge associated with pillar extraction introduces additional safety risks during the activity. Although pillaring developed prior to mechanized mining, current technology and mining practices have made this form of mining highly modernized. However, current fatality trends suggest that work still needs to be done to control the residual risk that is not controlled by modern practices, such as those having a personnel-performance-based component. This paper investigates the application of modern coal pillaring techniques and will present a risk-management-based strategy that targets personnel-performance-based risk, in order to improve the ability of safety engineers, managers and trainers to provide training programs addressing the needs of pillaring sections.

Jan 1, 2012

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

"Despite being a field of study that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world, consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited, while the only contact that undergraduate students have with mining operations during their time of study is usually through shorttime internships or visits in the context of educational trips. Real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes and thus understand the whole picture of mining operations.Indirect practical training is now possible since that technology is shifting from mechanical to digital, and the use of virtual reality — in the context of Mining 4.0 — can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al., 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other, especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers.Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and knowhow could be developed and/or enhanced, are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.An early example of asolely experimental mines is the Luossavaara-Kiirunavaara Mine site operated by LKAB in Sweden, where systematic research on rock mechanics and mining engineering was successfully carried out in the 1980s. As a result, the developed underground mining technology was applied in LKAB’s mines at a later stage. There have also been research mines within collieries such as the former Lake Macquarie Mine at New South Wales in Australia and the Zeche Tremonia Mine in Germany), but these are no longer in operation (Mischo, 2015)."

Oct 1, 2019