Search Documents

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors in¬fluencing the variation in face emissions between the two mines will be discussed.

Jan 1, 1997

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By Irwin R. Higgins, Richard S. Dennis

Acid recovery employs ion exchange resin as an adsorption media for the separation of inorganic acids from mixtures of acids and their metallic salts. This technology has been used to treat spent pickling and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. Acid recovery can also be used for electrolyte treatment to facilitate valuable metal recovery and to improve product quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process strong acid concentrations. TETRA'S CCIX™ continuous I-X contactor has been used successfully in a simple, continuous operating mode to separate acid from its salt. Efficient separation is enhanced by refluxing which allows acid to be produced as a salt-free product at nearly its original strength. Continuous treatment also recovers heat to the bath and improves metal quality due to consistent acid quality.

Jan 1, 1995

By S. G. Malghan

This paper reviews uses of sodium sulfide in the flotation of oxide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance, the nature of the heterogeneous reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. Recent studies on sodium sulfide addition to flotation pulps, monitoring its concentration, and the optimum dosage control using platinum and/or sulfide specific ion electrodes are discussed.

Jan 1, 1987

By P. V. Avotins, D. R. Nagaraj, S. S. Wang

Xanthates and dithiophosphates are the most commonly used collectors in the flotation of sulfide minerals. Other reagents such as thionocarbamates, mercaptobenzothiazoles (MBT), mercaptans and xanthogen formates occupy niche positions in industrial collector use. Over the last ten years there has been much activity by chemical companies to develop new collector compositions. The new collectors are aimed at meeting specific process needs such as recovering an increment of valuable metals, improved sulfide separations, increased flotation kinetics, and reducing reagents costs. A review of the patent literature shows that American Cyanamid (Cytec), Dow Chemical, Phillips Petroleum, Sentrachem Ltd., Henkel, Montan Chemicals and Elf Aquitaine, among others, have been active in sulfide collector research. Several companies have achieved considerable success in laboratory and plant tests of the new collectors; however, commercial acceptance for plant usage has been slow. Those most advanced have been plant tested extensively and some are in day-to-day use. The new collector types in this category are: Modified thionocarbamates, dithiophosphinates, organic sulfides, trithiocarbonates, monothiophosphates, and modified thioureas. Others such as substituted mercaptobenzothiazoles and monothiophosphinates have been tested in the laboratory. The chemistry of collectors developed in the last 10 years, their preparation, physical properties and their potential for commercial use are reviewed in this paper.

Jan 1, 1994

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By William M. PhD. Schafer

The net acid generation (NAG) pH method is an important analytical tool that supplements static and kinetic tests for assessment of the acid generation risk of rock samples. This method is useful because it is simple, rapid and cost-effective; it combines features of the static and kinetic tests; and it can be conducted at mine assay labs. The NAG pH test is particularly effective for operational testing programs used to classify, selectively handle, and route potentially acid-generating waste rock. The NAG pH procedure is based on a 24 hour oxidation of a pulverized rock sample with hydrogen peroxide and subsequent measurement of the sample's pH. If the NAG pH is below a critical value, determined empirically, then the sample has the potential to generate acid in the field. The critical NAG pH value is typically within the range of 3 to 4.5, but the exact relationship between NAG pH and potential acid generation should be determined individually for each mine site, based on comparison with results of acid base accounting, humidity cell tests, and mineralogical analyses. Calibration and use of the NAG test for predicting ARD risk at several mines are described in this paper.

Jan 1, 2000

By Arpad E. Torma

The introduction of biotechnological principles in hydrometallurgy has created new opportunities and challenges for the industry of mineral processing. During the 1950's and 608s, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes, especially for the production of copper and uranium. The economic viability of bio- leaching technology lead to its world-wide acceptance by the mining industries. During the 1970's this technology grew into a more structured discipline which is called "biohydrometallurgy". Currently, bioleaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, gold and silver from diverse mineral resources and for the desulfurization of certain coals. However, in a foreseeable future the biohydrometallurgical processes may be applied also for the treatment of high- grade ores and mineral concentrates using native and/or genetically engineered microorganisms.

Jan 1, 1989

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By J. A. King, D. R. Weir, P. C. Robinson

Preconcentration of Porgera ore results in high recoveries of gold into gravity and flotation concentrates. The bulk of the gold is contained in auriferous pyrite flotation concentrate and is not readily recoverable by direct cyanidation. Oxidation in autoclaves at high pressure and temperature produces a residue that contains the gold in recoverable form. Pilot plant treatment of the autoclave residue is described, through washing and jarosite decomposition stages, to cyanide leaching and recovery of gold and silver by carbon-in-pulp techniques. The concern associated with disposal of plant effluents are also addressed.

Jan 1, 1987

By Randy Fulton, Ignacy Puszkiewicz, George H. K. Schenck

Stuart Olson Construction, Inc. excavated 385m (1263 ft.) long twin tunnels with 6.25m (20.5 ft.) O.D., a portal and a cross-over for the Edmonton, "Metro". The work for Contract No. 76458, SLRT South Tunnel and Portal, in Edmonton, Alberta, Canada was performed in 1989 and 1990. NATM was specified because of the instability of glacial deposits. The contractor decided to use "two firsts" on this project: Fully mechanized NATM and a novel excavator¬mounted tunneling machine. An excavator was equipped with a cutter boom, and a loading and conveying system. This novel machine cost only about one-third of the price of a special NATM roadheader. This new combination of NATM and an excavator-mounted cutter boom offered a cost-effective alternative to shields, slurry TBMs and roadheaders for short tunnels in unstable ground. For NATM tunneling in hard rock or in mixed faces, the roadheader-type cutter boom can be replaced with an impact hammer (hydraulic breaker).

Jan 1, 1993

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By A. W. Khair, M. Ahmad

Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion, oxidation, or diffusion, depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been camed out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation.

Jan 1, 1992

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006