Search Documents

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By D. R. Dolinar

Geogrids can be used as surface control on both the roof and rib in underground mines to prevent the fall of small pieces of rock and material from between the primary supports. The use of screen material such as geogrid can significantly reduce the number of ground fall injuries caused by these small rock falls. Because of the potential for reducing injuries through the use of screen, the National Institute for Occupational Safety and Health (NIOSH) has conducted tests on screen materials including geogrid to determine their support characteristics and identify parameters that can affect their performance with respect to maintaining broken or failed rock. A specially designed test frame installed in the NIOSH Mine Roof Simulator (MRS) has been used to evaluate the load and stiffness characteristics of the screen material. Two types of geogrids with various designs have been tested-a polyester yarn and a polypropylene grid. The load-displacement characteristics of these grids were determined and the load capacity and stiffness were calculated through 20in of displacement. The load capacity and stiffness of the geogrid in general are shown to be related to the ultimate tensile strength of the screen material.

Feb 27, 2013

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By Jill Murray

This study focuses on the amosite mining region in South Africa and associated health effects, compared to other mined asbestos fiber types. Historically, dust and fiber levels were high in the amosite mills and mines, and many miners and members of the surrounding communities were exposed to the fibers. Research has shown that amosite produces both benign and malignant disease. Nevertheless, the mesotheliomagenic potential of amosite is several fold lower than crocidolite. The risk of disease associated with amosite exposure is difficult to quantify. Reasons for this include the scarcity of available information, including fiber measurements, and case ascertainment, as well as the juxtaposition of the amosite and crocidolite asbestos seams in South Africa. © 2007 Elsevier Inc. All rights reserved. Keywords: Amosite; Mesothelioma; Crocidolite; South Africa; Asbestos

Jan 1, 2007

By S. Angioletti

This paper addresses strategic investment decisions when they are nested in a project development format where each project is implemented in phases and each phase is approved to move on to the next phase only if certain technical and economic requirements are met. This configuration is sometimes referred to as a ?Project Portfolio?. Mining companies maintain project portfolios in their exploration investment plan. This study proposes a procedure to best manage an exploration project portfolio including technical and economic uncertainties. The procedure may support decision makers in a simple and intuitive way, while maintaining the rigor and precision required by the rather large amount of financial resources typically called for by mining projects. The procedure was tested in a real case study of a gold mining company and its exploration projects portfolio. The procedure uses the following approaches: i) investment valuation methods under technical and market uncertainties based on Option Pricing Model, Real Option Theory and Option Space; ii) portfolio management and Stage Gate®1 method; iii) Monte Carlo simulation.

Jan 1, 2010

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without king reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county mad and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Feb 24, 1997

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article is based on research report data from minecost.com and Metalytics Pty Ltd which detail the specific carbon dioxide emissions for 208mines producing 90% or more of western world copper, zinc, lead and nickel in 2007. The copper and nickel mines also include Norilsk in Russia, KGHM in Poland and Kazakhmys in Kazakhstan. This is the first time that such information has become available.

Jan 1, 2009

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By Alfred Weiss

Selecting a minicomputer is not unlike selecting a costly piece of mining equipment such as a truck, shovel, crusher, or conveyor belt system. A marked difference might lie in the frequency at which such selection takes place; another difference might be mine management's familiarity with mining equipment vis a vis a minicomputer. These basic differences might prompt a mining company to seek the aid of a consultant when selecting a minicomputer system. Advantages and Disadvantages The fundamental advantage of employing an independent consultant is that it provides management with a source of knowledge and breadth of experience not readily available within the organization. If the consultant has a minerals background, such knowledge and experience are further enhanced by actual experience in exploration, mining, and mineral processing. If the consultant has worked within a mining company, such hands-on experience is supplemented with a meaningful understanding of the client's business; this facilitates communication between the consultant and members of the client organization. The consultant has been, so to speak, "in the client's shoes." There are several other advantages. Since computer systems cut across organizational boundaries, the independent consultant may be able to move within the organization more easily than an inside staff person to collect necessary information. Also, detachment from any manufacturer should provide the client with an objectivity and a set of recommendations as near optimal as feasible. The principal disadvantages lie in the area of continuity and accountability. Once the consultant's report has been submitted and his recommendations implemented, a discontinuity might occur. Also, if implementation does not provide the desired results, the consultant might not be available to correct the situation or account for actions taken. Proper selection of consultant services, relative to kind and duration, and the consultant's method of operation, will often prevent many of these aftereffects. Services Offered The professional consultant can help a client: •Define and summarize information systems technology* needs; • Evaluate alternatives such as in-house capability and capacity, time-sharing, or service bureaus; • Prepare a formal request for proposal (RFP) to be submitted to vendors; •Evaluate vendor proposals; •Evaluate the economics of lease vs. purchase; and •Assist in the conversion and installation. Thus, consulting services may range from evaluating an existing system and upgrading to a larger piece of equipment, to selecting a new first-for-the-organization computer. First, Define and Summarize Needs Regardless of circumstances, the most valuable document required before equipment selection is the information system plan (I/S plan). It helps insure that the company's information needs are met in a cost-effective manner. An I/S plan is usually a comporient of the mining company's overall business goals. Since an I/S plan is a formal vehicle for establishing and communicating the direction the organization intends to take to satisfy information requirements needed to achieve goals and objectives, most initial systems services are likely to center around creating such a document or updating an existing document. The trend toward company-wide I/S planning is increasing in the mining industry; however, smaller scale efforts focused at the information systems needs to support an individual

Jan 11, 1981

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011