Search Documents

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997

By M. Abdel-latif, R. W. Bartlett, P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines was designed and operated. A nontransferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained above 1673 OK (1400°C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbonmonoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pres- sure and average reactor temperature. The interaction of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1995

By John Waggoner, Steve Klein, John Townsend, Jay Arabshahi

The Riverside Badlands Tunnel is a 13 km (8 mile) long segment of the Inland Feeder Project. This 3.65 m (12 ft) finished diameter water tunnel presented many challenges that had to be overcome to take the project from concept to reality, not the least of which were the diverse ground conditions. Construction of the tunnel was carried out by a single tunnel boring machine (TBM) in one tunnel drive. The project is considered a success due to the accurate baseline established for the ground conditions; the approaches used to mitigate adverse conditions; and the appropriate use of TBM excavation methods, which achieved rapid advance rates despite the challenging ground conditions.

Jan 1, 2003

By Ken A. Pfaff, Ray Daigh

This paper will discuss state-of-the-art applications of GPS automation in mobile conveying systems. Robotic mobile conveying systems increase profitability, optimize stacking and reclaiming operations, and control complex interfaces more accurately than other systems. We will also discuss the application process in machine-to-machine coordination, selection of the appropriate GPS system, and Ethernet considerations. As the leading supplier of GPS-controlled mobile conveying systems, we'll draw on our experience at Morenci, Radomiro Tomic, Zaldivar, El Abra (Figure 1), and El Tesoro mines in the US and South America to demonstrate system reliability and the lessons we've learned through analysis of these projects.

Jan 1, 2002

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit' data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO's increased geochemical activity.

Jan 1, 1982

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By B. K. Baird, P. C. Satchwell

The application of cutoffs during and after pit optimization is examined for a lower-grade multimetallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block. The calculation incorporates parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which parameters have significant effects on the total contained resource tonnage and total contained nondiscounted revenue in the optimized pit. The cumulative effects of changing several of the more-significant parameters are investigated The application of a copper cutoff grade to a block inside the optimized pit could result in the less-than-optimal extraction of the resource. A block with a copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher-copper-grade block may be subeconomic. Also discussed are the merits of applying a copper-grade cutoff, an "equivalent-grade" cutoff and a dollar-per-ton cutoff to blocks inside the optimum nit.

Jan 1, 2002

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Douglas W. Fuerstenau

This paper concern the specific adsorption of sulfate anions on nonmetallic minerals and its role in flotation. The specific surface affinity of sulfate ions in various systems has been observed in the results of electrokinetic measurements that show conditions under which sodium sulfate can reverse the sign of the zeta potential. The electrical double layer model provides a means for interpreting the results and for estimating the free energy of adsorption of sulfate ions. Because of their surface activity, sulfate ions not only can function as a depressant in the flotation of oxide minerals with physisorbed anionic collectors but also can function as an activator for flotation with physisorbed cationic collectors. Their role in depressing or enhancing the flotation of the sparingly-soluble mineral barite is also explained in terms of the double layer model.

Jan 1, 2005

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By G. T. Adel

The selective recovery of fine particles by flotation has been a long-standing problem in the mineral processing industry. Fundamental studies carried out at Virginia Tech since 1980 have suggested that many of the problems encountered in separating fine particles can be alleviated by using significantly smaller air bubbles than those used in conventional flotation processes. The main advantage of using smaller bubbles is found in an increased recovery rate, which can be attributed to an improved bubble-particle collision efficiency. This concept has been applied in column flotation as a means of improving flotation kinetics. A computer simulator has been developed to better study the effects of various parameters on flotation column performance. The simulation results suggest that the use of small bubbles and tall columns improves the recovery of fine particles while a judicious use of wash water greatly improves product quality. Information collected as a result of this analysis has been applied in developing scale-up relationships for column flotation.

Jan 1, 1989

By C. Anastasiadis

The wettability of sandstone was investigated using the technique of dielectric spectroscopy in the frequency interval 1kHz-1MHz. The natural wetness of the material was modified to get two different sets of samples, one with sea-water wetness and the other with crude oil wetness. Measurements showed that the electric responses of water-wet and crude oil-wet samples were markedly different beside the fact that the dielectric response of both groups of samples obeys a general fractional power law. The dispersivity, of the complex permittivity component that expresses the material loss with respect to the electric field was found to be the most suitable parameter to check the wettability of the samples.

Jan 1, 2005

By E. F. ‘Pat’ Nelson, Richard Broom

Our portion of this afternoon’s session is dedicated to the operation of automatic process control associated with small to medium size primary or SAG milling circuits. In recognition of the subject matter of this symposium, specifically precious metals, our historical reference is Rosario Dominicanna in the Dominican Republic, one of the largest gold producers in the Western Hemisphere. Plus a backward glance to review very briefly the initial performance of the big primary mills at Island Copper in British Columbia and Pima IV in Arizona. We will then get to the subject at hand with a discussion of a retrofit control logic recently installed on a 5000 hp primary mill. The focus of this review is the simple, inexpensive, and cost effective character of this retrofit installation.

Jan 1, 1984

By C. H. Lee, F. Concha, L. G. Austin, P. T. Luckie

The Concha-Almendra batch-settling treatment for concentrated suspensions of single-diameter spheres has been modified. This modified version is used in the differential equations of simple batch settling of a particle size range of different density materials. The equations have been programmed for a finite difference solution, and a number of test cases have been analyzed. By cutting the settling column at a fixed fractional height, the material below this height can be treated as underflow and the material above as overflow. The predicted partition curves obtained from treating the settling in this way have Sharpness Indices in the range of 0.5 to 0.6, in the absence of dispersion effects. The Sharpness Indices decrease as dispersion increases. When the feed size distributions are of the Rosin-Rammler form, the partition curves (corrected for the bypass fraction) fit the Rosin-Rammler equation with reasonable accuracy. The predicted Sharpness Index of a component of a mixture of two materials of different densities was unchanged from that of the same materials settled alone. However, for the same, feed size distribution and volume fraction of solids in the feed, the heavier material settled faster, and the lighter settled slower, than when settled alone.

Jan 1, 1993

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

By Fernando de Oliveira Durão

A complete computer package for the steady-state simulation, either in analysis or in design mode, of mineral processing flowsheets is described. The main features of the simulation package are: modular architecture, flexible structure and sequential solution strategy. Different detail levels of mathematical models of several mineral processing unit operations have been developed and implemented as unit modules (FORTRAN routines). Unit operations currently modelled are: coarse/fine crushing, grinding, screening, hydrocyclone classification, gravity separation, heavy media separation, froth flotation, high gradient magnetic separation and solid-liquid separation. In design mode, a simulation study is stated as a general non linear optimization problem. The objective function is a weighted sum of square deviations between the design specification set points and the calculated values, subject to non linear equality and inequality constraints. The optimization problem solution is obtained solving successive Quadratic Programming subproblems followed by inexact line search of an exact penalty function (Powell algorithm). One non trivial example is discussed, illustrating the design capabilities of the simulation package.

Jan 1, 1992

By Graham A. Mathieson

A detailed breakdown of capital and operating costs is an essential element in the planning and evaluation of any mining project. The OPCOST System was developed by Golder Associates to provide mining engineers with the facility to synthesize detailed cost estimates for all aspects of an operating or potential open pit mine. The system can also be applied to underground mines equally as well. Such estimates can be prepared at a variety of levels depending on the detail required by the project. The OPCOST System is a suite of computer programs linked through a common hierarchical data base. It simulates the thought and reasoning processes within the quantity takeoff and cost estimation phases of a mining project. The system was developed as a mining cost engineering tool on the basis that it would have to satisfy a variety of purposes, namely:

Jan 1, 1982

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By J. Peck, M. J. Scoble, C. Hendricks

This paper is based on field studies in North American surface mines. The work involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board rotary blasthole drills and mining shovels. Following a review of instrumentation and monitoring methodology - drawing on experience gained under field conditions-the paper will focus on the application of monitoring technology within the framework of an Integrated Equipment Monitoring System. Such a system will permit real-time performance evaluation of key equipment involved in surface mine production. Drill performance monitoring has been demonstrated through work to date, to provide significant input into blast design, reserve estimation, mine planning and production control processes, through an improved facility for ground characterization. Monitoring excavation equipment has been proven valuable in assessing how effectively the input from drill monitored data has been used in the evolution of blast designs. This specifically refers to assessing blast efficiency through measuring associated levels of excavator performance in relation to muckpile characteristics. The medium-term goal of equipment instrumentation and monitoring has been to assist mines in optimizing the overall rock breakage and handling process. Based on the reported results, this has been accomplished. Long-term efforts now concern using a greater understanding of equipment performance and response to varying operating conditions as a foundation for the implementation of mining automation.

Jan 1, 1993

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989