Search Documents

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier's law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962

By W. R. Hardwick

This information circular describes mining methods and practices at New Cornelia Branch, Phelps Dodge Corp., Ajo, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The New Cornelia mine (fig. 1) is at Ajo, a town in southwestern Arizona (fig. 2) on Arizona State Highway 85 in the western part of Pima County. The [oncentrator] and smelter are near the mine (fig. 3). Copper ore is mined, crushed, ground, and concentrated, and the concentrates are smelted. Copper is cast in anode form and sent to the Phelps Dodge Corp. refinery in El Paso, Tex.

Jan 1, 1960

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

"An active list of permissible explosives was published in July, 1930 as part of the United States Bureau of Mines Report of Investigations 3025, under the title of “Active List of Permissible Explosives and Blasting Devices Approved Proir to June 30, 1930”. Changes on that list were authorized in August, September, October and November, 1930, and January, March, April and June, 1931, as published in Reports of Investigations 3029, 3037, 3046, 3053, 3069, 3089, 3099, and 3123, respectively, By these changes the following explosives were added to the active permissible list:Big Red No. 9 Hercogel CBlack Diamond No. 5-A Liberty No 1Black Diamond No. 9 Liberty No. 2Burton 5, L. F. Liberty No. 3Burton 7, L. F. Liberty-Gel L.P.Duobel No. 4, L. F. Wesco Coal Powder No. 1Genigel No. 1and the permissible explosive EP-28 was transferred from the active to the in active list of permissible explosives.During June the following permissible explosives were added' to the active permissible list:Austin Red Diamond No. 9-B, L. F. BurtonAustin Red Diamond No. 9-C, L. F. Gelobel No. 4, L.F.Austin Red Diamond No. 10-A, L. F. Liberty No. 6Austin Red. Diamond No.12-A, L. F. Monobel 8 L.F.,- WR Austin Red-D-Gel"

Jul 1, 1931

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By R. V. Higgins

"INTRODUCTION When nations throughout the world are pitted against each other in a war in which petroleum plays a major role, scientist and engineers of the petroleum industry must give serious thought to ways and means for recover¬ing greater percentages of oil from natural reservoirs than in the past. Petroleum and its products are vital to highly mechanized modern warfare, and the victorious nations will be those whose armies, navies, and air forces are supplied with adequate fuel oil, gasoline, and lubricants until the war is won.Efficient recovery of oil from underground reservoirs depends on many interrelated techniques; evaluation of the producing performance of wells upon the basis of their productivity indexes is one such tool. Oil wells usually yield oil at a maximum rate when first ""brought in"". The rate of production begins to decline soon after the first oil is delivered to the tanks, and although part of the decline usually can be attributed to natural reduction of reservoir pressure as oil and as are withdrawn from the reservoir, a larger proportion frequently is caused by greater saturation of water and as in the producing formation about wells and clogging of the pores of the sands by silt, organic salt, and insoluble hydrocarbons. If the maximum quantity of oil is to be recovered from reservoir sands and rocks by wells, it is then imperative that the ability of wells to produce oil be watched closely and all adverse influences that affect the case with which oil can flow to wells be corrected if possible."

Sep 1, 1942

Ground-water and tailings pond monitoring in the Upper Santa Cruz Basin Mines Task Force's Special Studies Area has been performed to determine the nature and extent of aquifer contamination from copper tailings pond's recharge in the basin. A monitoring program for each of three mining areas (Mines A, B, and D) was developed. Analysis of data shows that recharge from Mine A's ponds has caused increased hardness, sulfate and total dissolved solids in local ground water. However, pumpage in the area has controlled most of the water's movement. Pond recharge from Mine B has led to similar conditions, and the degraded water is moving towards a local public-supply well. Pumpage from Mine D's interceptor wells is controlling some, but not all, of the movement of recharge seepage from Mine D's ponds. Recommendations include the need for enhanced monitoring programs at each current mine site, development of a monitoring program for Mine C's area, development of water budgets for all mines, investigation of tailings pond compaction and sliming, establishment of mine closure plans for containment of recharged pond water, and the need for additional interceptor wells in several locations.

Jan 1, 1983

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

Reduce the number of accidents in which large mining trucks crush objects that were not visible to the driver. Approach Improved rear view mirrors, light-bending plastic lenses, and a closed circuit TV, are combined in a rugged system that allows the driver to see almost all areas around a large raining truck. How It Works Improved mirrors, used in place of ordinary left and right rear view mirrors, give wider angle viewing. Fresnel lenses, two mounted on the front edge of the hood and another one mounted above the right front fender, show objects close to the front and right side of the truck. A rugged closed circuit TV camera mounted above the rear axle reveals objects behind the truck. See diagrams showing reduction of blind area around a 150-ton mining truck. The improved mirrors for rear viewing are approximately rectangular. The left rear view mirror has a flat reflecting surface 10 inches wide by 20 inches high. The right rear view mirror is curved to give wider viewing angles, both from left to right and up and down. This mirror is 12 inches wide by 16 inches high. Its convex reflecting surface has the same curve as the surface

Jan 1, 1979

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978