Search Documents

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By S. S. Venkata

This volume describes a comprehensive program of research into the reliability of mine electrical power system components and the resultant reliability of the total system. The research effort encompassed analytical models, laboratory testing and field testing. The analytical work included definition of terms, fail rate functions and distributions, failure rate estimation and techniques and procedures for theoretical reliability assessment. One of the primary mine power system components addressed in the study was the ac molded case circuit breaker. This device is known to have low reliability and hence an unfavorable impact on mine safety and productivity. Ac molded case circuit breaker reliability was studied by analytical means, laboratory testing and field monitoring. A similar three-pronged' effort was made to study the reliability of undervoltage relays/releases. Particular emphasis was placed on new solid state undervoltage relays. The reliability of bulk power components, such as trailing cab les, motors, control gear, and other equipment, was assessed by gathering maintenance records from active mines. These data were compared to similar records from other industries. The work was extended to include the reliability, availability, maintainability and safety of these components.

Jan 1, 1979

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By E. G. King

Heat of formation values for mercuric sulfide appear in all the comprehensive listings of thermodynamic data, but experimentally determined entropy values have been lacking. Consequently, all free energy calculations involving mercuric sulfide have been based upon estimated entropy values. This paper reports Bureau of Mines measurements of the low-temperature heat capacity of red mercuric sulfide (cinnabar) and the entropy value at 298.15° K. derived therefrom. The entropy value was combined with heat data to obtain free energy values for the formation of red mercuric sulfide from liquid or gaseous mercury and from rhombic or gaseous diatomic sulfur.

Jan 1, 1962

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By EDGAR K. SOPER, Clarence A. Wright, DOUGLAS C. LIVINGSTON, Thomas Varley

In 1917 the Federal Bureau of Mines and the University of Idaho arranged to cooperate in an investigation looking to the improvement of mining and milling methods in the mining districts of the State of Idaho, with an especial view to the wider development of the minerul deposits and greater efficiency in the treatment of the lowgrade ores of the State. This work has been made possible lnrgely through the generosity and active assistance of the mine operators, especially certain companies in the Coeur d'Alene region. As the first step in the work under the cooperative agreement it wa.s decided to gather all data possible on the various mining districts throughout the State, both active and abandoned, in order to ascertain their potential possibilities, especial attention being paid to methods of metallurgical treatment and to the solution of the many metallurgical problems in order to effect a greater commercinl saving. With this plan in view, field work was begun in the latter part of May, 1917, and was continued during the summer. E. K. Soper, formerly professor of mining, University of Idaho, and now dean of the mining department of Oregon Agricultural • College, Corvallis, Oreg., visited the mining districts in central and southwestern Idaho and also some of those in the northern part of the St.ate. D. C. Livingston, professor of geology at the University of Idaho, Moscow, Idaho, also visited some of the mining districts in central Idaho during the summer; in addition, much valuable information he had gathered on former trips to many other districts is included in this report. Credit is also due Mr. Livingston for the maps covering the State, as well as the bibliography nt the end of each chapter. Thomas Varley, superintendent of the Seattle mining experiment station of the Bureau of Mines, spent a short time in the field, principally in the mining districts in central and . northern Idaho, and made a brief visit to the southwestern districts with Mr Soper. The field work of Mr. C. A. Wright, metallurgical engineer of the Bureau of Mines, in direct charge of the cooperative work, was chiefly in the Coeur d'Alene region. Mr. Wright visited nearly all of the mining districts in the region and devoted most of his time to studying the milling methods. The results of the investigation are set 1iorth in this bulletin. The bulletin aims to give the l9Calities of the various mining districts, and the nature of the present operations and those that have been carried on in the past. The geology is discussed only in a general way, the descriptions being intended more especially to bring out the types of ore deposits and the character of the ores, a knowledge of which is essential in determining the proper treatment of the ores. The writers do not wish to imply that all districts mentioned in this bulletin were visited during the summer of 1917, for a great deal of the material has been gathered from other reports, especially from publications of the United States Geological Survey. However, it is hoped that this report will be of help to those who are interested in mining in the State of Idaho. The plan is to continue the field work and subsequently publish the results of the investigations in much more detail, with greater emphasis given the metallurgical treatment of the ores and the problems involved.

Jan 1, 1919

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

By Almon F. Robertson

"INTRODUCTION At various times, North Carolina has supplied small quantities of brown-iron ore to the furnace o the South. Between 1917 and 1920, the quantity reported to the Federal Geological Survey was 126,000 tons. Most of this came from Cherokee County. 3/In furtherance of the program initiated by the Bureau of Mines to develop additional reserve of iron ore during the emergency, the Cherokee County deposits were examined by an engineer 4/ of the Bureau of Mines, and work was recommended on,12 properties.The project was begun in April 1944 and continued intermittently until April 1945, when work was stopped. During this period, eight properties were explored, and an additional property was mapped.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch; Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007