Search Documents

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By Charles L. Kimbell

For 1991, the aggregate value of world international export trade in mineral commodities was roughly estimated at $685 billion in current 1991 dollars. The estimated level was about 6 % higher than that for 1990, but still more than 3 % below the record high set in 1980, and the year was the fifth in a row in which the value of exported minerals advanced. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1991, as well as a breakdown of this total into fuel and non fuel commodities. The data shown are based on the historically more traditional and realistic (from the viewpoint of data availability) practice of reporting trade values for the year before the year of review. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1 %, this share was very near the recent year record low of 19.0% reached in 1988. Comparable 1991 figures were not available in time for inclusion here, but it is expected that the mineral commodity share of the total will be little altered from that of 1990.

Jan 1, 1993

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By Joseph P. Flick, Kathleen M. Kowalski, Lynn L. Rethi, Roberta A. Calhoun

Many miners are involved in tasks at the mine site that are similar to those sub-tasks performed in general construction, maintenance and repair (CMR) type work activities. As a result, many of the injuries in the mining industry today can be traced to employees performing these CMR type work activities. Indeed, a recent analysis of a major aggregate company revealed that 65% of all injuries documented originated from performing such CMR activities. It is hypothesized that the number of injuries to miners performing construction, maintenance and repair (CMR) work activities on mine property may be reduced through improved training that focuses on better hazard recognition using the numerous visual and other cues that are available for evaluating workplace health and safety hazards. To this end, researchers at NIOSH’s Pittsburgh Research Laboratory have merged two proven methods of training miners to recognize hazards, stereoscopic (3-D) slides and the concept of degraded images, into this training program. Stereoscopic (3-D) slides have been shown in earlier NIOSH and U.S. Bureau of Mines research to be an effective training aid for improving the ability of miners to recognize various geologic and mining-induced irregularities that can cause groundfalls.3 They realistically portray the natural mine environment, and thus are an excellent training aid for teaching miners to recognize such visual cues. The degraded image concept, originally developed by the military and used for target detection training, describes scenes where the target is partially hidden by cloud cover, dust, rain, natural barriers, buildings, or other obstructions that can camouflage or confuse the target. Research had shown that flight observers who were trained with less than ideal (or degraded) pictures were more successful in subsequent identification of targets than those trained using ideal (or highlighted) pictures of targets. In order to investigate this concept for training miners to recognize hazards, NIOSH researchers developed a prototype hazard recognition training program using such mining scenes. A control program based on traditional highlighted mining scenes was also developed. Both programs were applied to subjects in a field experiment. Results indicated that miners trained with the degraded images did significantly better on a follow-up test of hazard recognition.4 This hazard recognition program teaches trainees to look for hazards in a more realistic manner than that of the control program. This specific training program for CMR activities involves using the degraded image concept and 3-D slides. The module is designed to educate workers on hazard identification techniques and safe work practices. It focuses on teaching miners techniques for recognizing visual (sight) cues, and then uses these cues to evaluate mining conditions. It should be stressed that other senses, such as sound can also play an important role in hazard detection.

Jan 1, 1999

By Michael J. Griffin

Science involves the study of the nature and behaviour of natural things and the knowledge we obtain about them. Scientific endeavour leads to the unfolding of new knowledge and adjustments to our understanding and our behavior. To indicate that we ‘know’ something may merely mean we do not feel able to, or that we do not wish to, disagree with others who claim to know; or it may mean we have either heard about it, or studied it, or understand part of it, or accept that it is true, or have seen evidence to be convinced of its veracity. What do we ‘know’ about the health effects of vibration? There are many unknowns in the field of human responses to vibration. Not all would agree on what is known and what is unknown. This paper seeks to summarize what we know that we know, what it is sometimes claimed that we know, and what we know that we do not know about the relation between exposures to vibration and our health. It also speculates on what we do not know that we do not know. Hand-transmitted vibration What we know we know We know that exposures to hand-transmitted vibration result in various disorders of the hand, including abnormal vascular and neurological function. Not all frequencies, or magnitudes, or durations, of hand-transmitted vibration cause the same effects. What we may claim to know To enable exposures to be reported and compared, they are ‘measured’ and ‘evaluated’ using defined (e.g. standardised) procedures. This involves identifying what is to be measured and specifying how it is expressed by one (or a few) numbers. Summarising a vibration exposure in a single value involves assuming the relative importance of components within the vibration (e.g. different magnitudes, frequencies, directions, and durations), so standards define ‘weightings’ for these variables. The importance of the weighted values may also be suggested, allowing ‘assessments’ according to a criterion (e.g. the probability of a specific severity of a specific disease). Standards for the measurement and evaluation of hand-transmitted vibration define a frequency weighting and time dependencies that allow the severity of vibration exposures to be assessed and the probability of finger blanching to be predicted 1. What we do not know We do not know that the frequency weighting in current standards reflects the relative importance of different frequencies and axes of vibration in producing any specific disorder. We do not know whether the energy-based daily time-dependency inherent in A(8) reflects the relative importance of vibration magnitude and daily exposure duration. Consequently, the relation between A(8) and the years of exposure to develop finger blanching, as in an appendix to ISO 5349-1 (2001), is not well-founded. We do not know, or at least there is no consensus on, the full extent of the disorders caused by hand-transmitted vibration (e.g. vascular, neurological, muscular, articular, central), or the pathogenesis of any specific disorder caused by hand-transmitted vibration, or the roles of other factors (e.g. ergonomic factors, environmental factors, or individual factors). We know that acute

Jan 6, 2006

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By George J. Conroy

Types and causes of short-circuit and open-circuit faults in mine portable trailing cables are discussed, and techniques for locating these faults are described. Time domain reflectometers (TDR) , tone generator, infrared sensing, and high voltage methods are covered. The paper summarizes Bureau of Mines research, including development of a ~DR/tone generator sender with auxiliary probe.

Jan 1, 1975

By M. E. Tyrrell

Work in this investigation was undertaken by the Bureau of Mines to demonstrate how waste glass might be utilized to lower the required firing temperature and firing time of structural clay products. Mixtures of waste glass and common clays were formed by stiff-mud extrusion and fired to the temperature required to produce a body having 6 to 7 percent absorption. Substitution of glass for one-half of the clay in a red body reduced the firing temperature 500° F, which made possible a 30-percent increase in production; in a tan body, the firing temperature was reduced 400° F, which made possible a 23-percent increase in production.

Jan 1, 1972

Table B-1. Summary of respirable coal mine dust samples collected under 30 CFR 90 by MSHA inspectors for underground occupations, 1988-92* [ ]

Jan 1, 1997

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

Design a high-production coal mining machine with inherent low dust generation and low frictional ignition potential. Approach Constant depth linear cutting (CDLC) provides a longterm solution to excessive dust generation from shearers and continuous mining machines through new design of the rotary drum culling system. Problems with rotary drum systems, which must be eliminated to control the dust generation at the source, include the effect of a con¬stantly varying depth of cut using fixed bit spacing, secondary fragmentation of already broken coal and, frictional heating of bits and entrainment of dust by fanning action due to high drum rotational speed, Each bit on a rotary drum enters the coal face at zero depth of cut, goes to some maximum depth at the horizontal centerline during sump, and exits at zero depth.

Jan 1, 1989

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper's four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator's cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985