Search Documents

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves, To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By Lloyd A. Morley

This report details the continuation of mine power systems transient research under USBM Grant G0155003. The purpose of the work, which commenced under Grant G0133077, is the elimination of safety hazards created by transients" and the objective is to provide knowledge about transients existing in a-c and d-c coal mine power systems. The report chapters cover theoretical background, instrumentation, and experimental investigations. The instrumentation discussion scans measurement problems and considerations plus the development of a low-cast peak-detector. Transient data from in-mine measurements are presented and include high-voltage distribution and d-c trolley systems. Extremely unique field exercises are described involving actual power equipment connected on the surface to duplicate typical underground coal mine system arrangements. Here, transients on high-voltage distribution resulting from vacuum circuit breaker operations could be observed under controlled conditions, and work centered around how surge capacitors effect transients. Using the in-mine and staged transient data, specific conclusions and recommendations are made with emphasis on high-voltage distribution.

Jan 1, 1977

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves. To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By Charles Zahn

Gas chromatography is a method of separating mixtures of gases and volatile materials by entraining their vapors in a gas stream, which passes over an appropriate stationary phase. Two techniques are in common use: Gas-Liquid Chromatography, in which the stationary phase is a liquid supported on an inert solid, and Gas-Solid Chromatography, where the stationary phase is a solid adsorbent, such as charcoal or alumina. In both techniques components emerge from the column after a characteristic residence time. Gas chromatography is applicable as a qualitative or quantitative tool in a wide variety of problems in chemical research and processing. It may also be employed for purification and separation. A running bibliography on gas chromatography has been maintained at the Bureau of Mines synthetic liquid fuels laboratories, Bruceton, Pa., for several years for the benefit of research workers, who use chromatography as an analytical tool. Since the number of references grew and interest in the technique became more wide-spread, the Bureau is publishing this list rather than maintain it as a purely internal source.

Jan 1, 1958

By Thomas M. Garland

Reports that set forth the pertinent facts of existing secondary-recovery operations are an integral part of the work of the Bureau of Mines in promoting conservation and efficient utilization of the petroleum resources of the Nation. Knowledge of the success or failure of waterflood projects in an area is very useful to other operators. Although projects will not have identical results, information concerning the flood performance, method of operation, and difficulties encountered on one project will help operators to determine the feasibility of flooding a similar sand and to select the methods of operation most likely to prove successful. The increasing cost of discovering and developing new oil reserves, as well as the unending effort to reduce operating costs and increase ultimate oil recovery from known petroleum reservoirs, has required the petroleum industry to evaluate continuously the performances of various secondary-recovery methods. Waterflooding was recognized early by the petroleum industry as a possible means of increasing oil recovery. From the early accidental floods in Pennsylvania and through many haphazard attempts to inject eater into oil-bearing formations, waterflooding emerged as one of the more important methods of oil recovery. Waterflooding is important not only to the oil industry but also to the economy of the area concerned.

Jan 1, 1962

By Michael R. Grubbs

The Bureau of Mines is currently developing methods for reclaiming the metal and mineral values contained in unburned urban refuse. One important phase of this research deals with recovering Mastic from shredded refuse using in electrodynamic separation process. The results of this study have indicated that mixed plastic concentrates analyzing 99.4 percent plastic can be consistently recovered from the light material fraction of shredded refuse, leaving a mixed paper traction analyzing 99.9 percent paper. Recovery of the plastic exceeds 99 percent.

Jan 1, 1972

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By V. R. Spironello

One of the primary objectives of the Bureau of Mines solid waste utilization program is the recycling of the magnetic fraction of municipal solid waste called raw refuse scrap. In this investigation, several types of scrap of differing quality, including refuse and turnings, were melted in a 1-ton electric-arc furnace in various combinations to produce steel in noncritical (construction) grades. In-formation on furnace operation and on the behavior of tramp and alloying elements was obtained. The research showed that it is possible to produce acceptable steel from a variety of steel scrap. Although some scrap is routinely used in steelmaking, it was found that up to 50 to 55 pct of the scrap charge can be ref-use, provided it is combined with higher quality scrap. The chemistry of the steels was generally acceptable, and all of them were rolled without difficulty. The specification (ASTM 615) for the steels produced was grade 40 or grade 60, containing 0.30 or 0.40 pct C, with mini-mum yield strengths of 40,000 or 60,000-psi, respectively. Most of the steels met the specification requirements. In-formation on typical microstructures of some of the steels is included. The composition of some furnace dusts showed high levels of Sn, Pb, and Zn.

Jan 1, 1981

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By R. H. Thompson

Six different types of blasting caps, mainly of the type used in coal mines, were evaluated to determine both their 1lF and DC characteristics. Two of the caps were of foreign manufacture. All the American made caps had "no-fire" (0.1% firing probability with 95% confidence, as determined by the Bruceton test) levels above 0.04 watts. One of the caps of foreign manufacture had a "no-fire" level of 0.023 watts. A worst case analysis of blasting cap pick up of RF power in coal mines was performed and safe distance curves were generated.

Jan 8, 1973

[ ]

Jan 1, 2012

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By J. A. Herdlick

"INTRODUCTION The Bureau of Mines began a broad program of exploration of various proportion in the Pine Creek area of the Coeur d'Alene mining region in the fall of 1943. As a part of this project, exploring was done at theLittle Pittsburg property in 1945. The work included driving a 500-foot crosscut from the No, 6 level and drilling four diamond core drill holes to test the behavior of the Little Pittsburg vein at depth. This report presents the data obtained by the Bureau.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The Bureau's exploration of the Little Pittsburg vein was one of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. The project was started by R. M. Gammell, mining engineer, and was continued by the author and J. R. Reynolds, assistant mining engineer.The chemical analyses included in this report were made at Reno, Nov., under the direction of A.C, Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines.The cooperation and assistance of the management of the Denver Development Co. is gratefully acknowledged, in particular that of C. E. Nugent, who made available much of the operational data included in this report."

Jan 1, 1947

By Ruth F. Brinkley

This report is the 17th of a series originally issued annually, and more recently bienially, to acquaint the reader with the work of the Division of Explosives Technology, Federal Bureau of Mines. It differs from preceding reports in that its material is presented in two parts: Part I reviews briefly the overall activities of the Division during fiscal years 1955 and 1956;4/ part II presents in abstract form, the publications of the Division during that period. As it is not unusual for research completed in the course of one report period to be published only in the following period, the Bureau believes that the present approach will give a more accurate presentation of its work for the period considered. The Bureau hopes too, that the somewhat more concise presentation will prove convenient to the reader.5/ PART I -RESEARCH AND TECHNOLOGIC ACTIVITIES The activities of the Division during fiscal years 1955 and 1956 reflected the steadily growing preoccupation with factors affecting the safety of permissible explosives and those affecting the tests used for approval of these explosives. Findings by a team of French investigators prompted a study of the influence of atmospheric moisture on the ignition of firedamp by

Jan 1, 1961

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954