Search Documents

By M. Howard Berliner

In August 1943 the Bureau of Mines completed seven churn-drill holes in an area of old mine workings near Linden, Wis., formerly known as the Argall mine. The work was undertaken as part of a general investigation by the Bureau of the zinc and lead producing area of southwestern Wisconsin at a time when special effort was being made to increase the production of metals necessary for war. The area was selected for investigation on the basis of its favorable geologic structure, past history, and apparent mineralization.

Jan 1, 1948

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all mineral to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of force applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective. A consideration of the possibilities of such a method for crushing led to some experimental work of a preliminary nature, the results of which are embodied in this paper. No systematic program was followed in the work and the results are, therefore, not final and far from complete. The success attained so far, with the mediocre apparatus available seems to warrant a preliminary report, with the expressed hope that the work may be carried on as well-outline program covering such phases as have been impossible to investigate at this time.

Jan 1, 1931

By H. J. Heinen

Malononitrile [CH2(CN)2J, which forms a carbanion in basic solutions, was investigated as a potential leachant for gold and was shown to be an effective extractant in alkaline pulps. Malononitrile was comparable to equal molar quantities of sodium cyanide (NaCN) in leaching gold from an oxide ore and yielded 10 to 20 percent higher recovery in leaching a refractory carbonaceous ore, although dissolution was slower with malononitrile than with cyanide. Complete recovery of the gold from the pregnant solutions was achieved by coprecipitation with a lead salt on zinc dust; the leachant was shown to be capable of regeneration and recycling a limited number of times. Addition of an anion-exchange resin to the carbonaceous pulp containing malononitri1e increased gold recovery from 67 to 95 percent. Some malononitrile derivatives were also shown to be gold solvents.

Jan 1, 1970

By D. Debasis, Christopher Mark, Gregory M. Molinda

The stability of any underground opening is, in large part, a function of the strength of the rock mass which surrounds it. The Coal Mine Roof Rating (CMRR) has been developed to quantify the defects in the rock mass and compile a strength value which can be used for engineering design. The CMRR has been applied to a number of ground stability problems, including chain pillar design, roof bolt selection, hazard assessment, intersection design, and numerical modeling. The CMRR procedure and some of these applications are described in this paper. The CMRR will soon be available in a Visual Basic computer program, allowing easy integration into exploration programs and standard roof fall assessments.

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By J. J. Forbes

The Coal Mine Inspection Branch of the Health and Safety Division, Bureau of Mines, was established to carry out the provisions in Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. The series of major disasters that beset the coal-mining industry in 1940 aroused public interest in mine-safety measures, and the act 18 the direct result of this rekindled interest. Under the provisions of the act, the Secretary of the Interior, acting through the Federal Bureau of Mines, is authorized and empowered to make, or cause to be made, annual or necessary inspections and investigations in coal mines, the products of which regularly enter commerce or the operations of which substantially affect commerce. The principal functions of the Federal coal-mine inspectors are to determine the causes of accidents and occupational diseases in coal mines and then endeavor to eliminate or ameliorate them (1) by revealing, through personal conferences with mine personnel, correspondence, and published reports, the unhealthful and unsafe conditions and practices existing in the mines and (2) by recommending practical means for correcting the conditions observed. The act does not provide any enforcement powers, and therefore compliance with the inspectors' recommendations is not mandatory; it does give Federal coal-mine inspectors the right to enter coal mines for inspection purposes.

Jan 1, 1951

By John R. Benham

The West Pioneer RARE II study area, No. 1-006 (fig. 1), has Figure 1.--NEAR HERE a high molybdenum resource potential. Two molybdenum-bearing areas are being explored by Utah International and by Cyprus-Moly Corp, Inc. using geophysical exploration and diamond core drilling. The study area also contains potential resources of gold and silver at six prospects: the Bear Paw (Ibex), Black Bear, Coeur d'Alene, Franklin No. 1, Martin, and Maynard. In addition, the Black Rear and the Martin contain possible copper, lead, and molybdenum resources. Most of the workings are caved.

Jan 1, 1981

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By F. S. LOTT

The number of petroleum refineries in the United States decreased from 399 on January 1, 1947, to 390 on January 1, 1948. On the latter date two additional refineries were under construction , a large one in New Jersey and a small one in Texas . This Crude oil charging capacity, based on complete facilities only , increased in 1947 from 5,569,482 barrels to 6,034,252 barrels per day , owing to material gains reported in all of the larger refining districts . great increase in effective capacity is only in part the result of the completion of major new units for crude-oil processing . Much of it is due to rearrangement and minor additions to existing facilities to permit more efficient and complete utilization . Recent experience has apparently demonstrated that many processing units are capable , with greater emphasis upon maintenance and precise controls , of sustained operations at higher volumes than were indicated in their old rated capacities . This situation doubtless has caused some upward revision in capacity data .

Aug 1, 1948

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995