Search Documents

By Doug Scott

Develop tools that companies can use to comply with 29 CFR 1910.1200.

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Ronald P. Hollenbeck

Samples of clays, shales, and slates from 29 locations in the Appalachian Region of Alabama and Georgia were tested and evaluated to determine their suitability as raw material for the manufacture of lightweight aggregate by the rotary-kiln method. Samples from 11 locations in Alabama (one each in Etowah, Lawrence, and Morgan Counties and two each in Colbert, Cullman, Tuscaloosa, and Walker Counties) and one location in Walker County; Ga., produced satisfactory lightweight aggregate.

Jan 1, 1969

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By H. D. Kline

Manganese ores have been mined in the Batesville district since 1849. Although not continuous over the intervening years, production had totaled approximately 432,000 tons of manganese ore and ferruginous manganese ore to the end of 1953. The ores occur in deposits, essentially low in manganese content, distributed over an east-west belt 24 miles long and 4 to 8 miles wide, the core of which is about 6 miles north of Batesville, Independence County. Although the reserves of high-grade ores in the district are comparatively small, the large deposits of subgrade ores and low-grade manganiferous material comprise potential sources of supply of manganese that may have increasing future importance. The manganese occurs as primary oxide and carbonate minerals in relatively flat-lying limestone and shale formations in which they were originally deposited and as oxides in residual clays resulting from decomposition of the shale and lime-stone. Most of the deposits underlie from a few to over a hundred feet of sedimentary chert, but many occur in the residual clays on exposed slopes of chert-covered hills.

Jan 1, 1956

By Elio Ferreira

This report describes the design, and development work performed to reduce the volume and weight of the miners caplamp battery, as well as a headpiece with a swivel mechanism containing a halogen bulb with two filaments. Work was also conducted in the development of a maintenance free battery. The design concept is based on non-sintered Ni-Cd technology, with an energy density of 22 Wh/lb. The cap lamp system developed has been approved by the Mine Safety and Health Administration (MSHA) and can be manufactured for mine use.

Jan 1, 1988

By L. B. Pankratz

High-temperature heat-content values of pure lutetium sesquioxide and dysprosium sesquioxide were measured over the temperature range from 298° to 1,800° K. Similar data for cerium sesquioxide were calculated from measurements of a mixture of cerium sesquioxide and dioxide and known values for cerium dioxide. The results for lutetium sesquioxide are regular. Dysprosium sesquioxide has a minor thermal anomaly near 1,590° K, the extra heat absorption being 220 cal/mole, Hexagonal cerium sesquioxide undergoes a transformation around 1,050° K, which is only slowly reversible; consequently results were obtained for both the low- and high-temperature varieties. The original heat-content data are reported, and smooth values of heat content and the corresponding entropy increments are tabulated. Equations were derived to represent the heat-content values.

Jan 1, 1963

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By R. A. Kearns

To enable the mining industry to be kept informed as to the availability of equipment developed by mining equipment manufacturers in their constant endeavor to keep a step ahead of changes in mining techniques, the Bureau of Mines periodically issues lists of equipment approved subsequent to the last previous listing. The present list covers those approvals issued during calendar years 1953 and 1954. It supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953. The procedure established in Bulletin 543 of numbering items in each category consecutively to indicate the chronological order of the approvals has been continued in this circular. Information on approvals issued later than January 1, 1955 may be obtained by referring to Coal Age, a monthly magazine issued by the McGraw-Hill Publishing Co.

Jan 1, 1955

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By M. C. Irani

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va., 40.7; Marion County, W. Va., 23.1; Buchanan County, Va., 22.1; Washington County, Pa. , 12.4; Greene County, Pa. , 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala., 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1974