Search Documents

Develop a 22-ton capacity temporary mine roof support light enough to be easily lifted and transported manually from one place to another. Approach Several potential approaches were investigated in developing a new temporary support. An all-hydraulic, high-strength aluminum design was chosen as the best. The support was designed, fabricated, and tested in several mines. The first units, built for 6- to 8-foot seam heights, have a load- bearing capacity of 22 tons, and weigh only 55 pounds. How It Works The lightweight hydraulic support is designed for use in any temporary support situation in place of wood posts or steel mechanical or hydraulic supports. This includes use prior to roof bolting in room and pillar mining and in longwall development sections, use as head and tailgate supports for a longwall, and use as turn posts and breaker posts in retreat mining operations. The supports feature a release valve for quick manual extension to roof level, a lanyard

Jan 1, 1983

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

By Robert L. Chufo

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of "seeing into the earth." A first generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full threedimensional (3-D) imaging system that will have applications in both the underground and surface environment.

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By H. H. Stoek

It would permit coal mines to operate continuously instead of intermittently . Intermittent operation increases the cost per ton for mining , and makes the yearly return to labor low . These conditions contribute to serious instability and unrest in one of the fundamental industries of the country and this can be changed only by coal buyers doing their part to insure steady work . The railroads are now required to transport the maximum amount of coal during the winter months when traffic is most interfered with by bad weather and when the maximum amount of coal is used by the railroads to handle other coal . The railroads now use nearly 30 per cent of the total output of coal . About one- third of their freight traffic is hauling coal , so that economy of fuel used by the railroads will produce a considerable gross saving .

Apr 1, 1920

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By W. W. Adams

luring the past two years the Bureau of ?,lines has been receiving from 100 to 150 coal mines in various States a report of each accident causing death, permanent total disability, permanent partial disability, or temporary disability lasting beyond the remainder of the day or shift on which the accident occurred. For each 100 accidents in these groups, there are perhaps from 35 to 45 accidents that do not disable the employee beyond the remainder of the day, and of these fraction-of-a-day accidents the Bureau has compiled no statistics. Information revealed by the reports is to the effect that falls of roof and coal in bituminous coal mines are responsible for 28 per cent of the temporary injuries to underground workers and 33 per cent of the days lost from all temporary injuries underground; they also indicate that falls caused 59 per cent of the deaths from all causes underground. Figures compiled by R. N. Hosler, of the Pennsylvania. Mine Rating Bureau, and covering accidents in bituminous; minis in that State, chow that 61 per cent of the deaths underground during the years 1917-1921 wore due to falls. Neither of these percentage figures includes deaths in major explosions; figures for all bituminous mines in the United States during the five years 1920-1024, inclusive of deaths in major explosions, show that 52 per cent of the deaths underground and in shafts were due to falls of roof and coal.

Jan 1, 1925

By E. D. Gardner

About five minutes after 3 o'clock on Thanksgiving morning, November 24, 1927, smoke was discovered coming up No. 2 shaft of the Magma Copper Co.'s mine at Superior, Pinal County, Arizona. Of the 49 men in the mine at the time, 42 were able to make their way to the outside unassisted, but 7 perished. Six bodies were recovered, and the seventh, that of an Apache Indian cage-tender at No. 2 shaft, is thought to be in the caved section between the 1,600 and 2,250 foot levels A second and independent fire broke, out in No. 1 shift about 2 a.m., November 27, burning .out the shaft timbers from the surface to the 200-foot level and destroying the surface fan and structures. About 20 men were underground fighting the fire in No. 2 shaft, but all were safely withdrawn, aril the fire in No. 1 haft was quickly controlled.

Jan 1, 1928

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

"An active list of permissible explosives was published in September 1935 as part of United States Bureau of Mines Report of Investigations 32S6, under the title ""Active List of Permissible Explosives and. Blasting Devices Approved. Prior to July 31, 1935."" This list included 154 brand names,Changes in the list that have been authorized subsequently placed 24 addi¬tional brands of permissible explosives on the active permissible list as a re¬sult of tests, changes in brand names, or transfer from the inactive list. Eight permissible explosives were transferred from the active to the inactive list. The present active permissible list contains 170 brand names. The brand names of the permissible explosives placed on the active list are as follows:Black Diamond Nu-Gel No. 4 By test.Black Diamond Special A,do.Burton 11, L. F. By change in name,Burton G, L. F. By test.Columbia B By change in name.Columbia C Do.Columbia D Do.Columbia E Do.Columbia. F Do.Columbia G Do.Columbia 1 Do.Columbia 2 D.Columbia 3 DoColumbia 4 Do.Columbia-Gel 1 Do.Columbia-Gel 2 Do.Genite 5, Do.Genite 7, Do.Genite G Do.Lump Coal C By test.Peerless No, 1 By transfer from inactivePeerless No. 8, L. F. Do.Tri-State Special No. 1 Do.Unilite No. 2 Do."

Dec 1, 1936

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

By T. R. Jolley

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: I. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in the county series that describes the preparation characteristics of the coals of Bell County, Ky.

Jan 1, 1957

By Gordon H. Dechman

This Bureau of Mines report presents an iterative approximation method for microseismic source location that was developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems, such as slope failure in an open pit mine. The source location method and two derivative location algorithms are described in detail, and the speed and accuracy of the two algorithms are compared.

Jan 1, 1977

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963