Search Documents

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the C2 through C5 paraffins, the C2 and C3 olefins and possibly the C4 and C5 olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pct of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By Irving Hartmann

The Bureau of Minas has been charged by the Congress with the responsibility for administrating the provisions of the Federal Coal-Mine Safety Act. One of the important duties of bureau inspectors under this act is to determine whether proper measures are taken to prevent mine explosions, which in moat miner includes Judea adequate rock dusting The investigation made after the explosion in Orient No. 2 mine, December 21, 1951, showed that much information is lacking on the adequacy of current rock-dusting and duet-sampling practices in the United States. To obtain such information, an intensive sampling survey was conducted by the Bureau in an Indiana coal mine. This paper summarizes the more Important findings from this survey, describes special samplings at several Pennsylvania coal miners, and discusses related studies in the Bureau's Experimental coal mine.

Jan 1, 1954

By C. W. Davis, M. W. Von Bernewitz, S. C. Lind

During the past few years our possible domestic resources of platinum have attracted much attention . On account of the extensive use of platinum during the World War , and the practical elimination of the Russian supply , the price of this metal rose to new high levels , as shown in Table 1 ; and though it since receded to some extent , the price is now nearly six times that of gold .

Jun 1, 1923

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By Charles E. Whieldon, C. I. Pierce

Data on the oilfields in Mahoning , Columbiana , Carroll , Jefferson , and Harrison Counties , Ohio , were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary - recovery operations in the area . General geology , oil production , oil - productive acreage , core data , reservoir calculations by townships , and miscellaneous data and reference material are presented .

Jan 1, 1965

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Comprehensive ventilation surveys are made to review the adequacy of the mine system with regard to both statutory requirements and/or company policy, to evaluate improvements to the current ventilation system and to plan for £stun expansion. If computer simulation is to be used for these purposes, accurate quantity and pressure measurements become an absolute necessity since the validity of the computer generated output is heavily dependent on the accuracy of the input data. Consequently ventilation surveys that are run to generate input data for computer simu¬lation must use the best data collection procedures to guarantee as accurate results as are possible. These requirements have led to modifications in procedures that are used for routine ventilation surveying. McElroy and Kingery (1957) have recommended that pressures be measured independent of quantities since minor changes in mine conditions have a greater effect on absolute pressure measurements than on quantity measure¬ments. They estimate that, for large mines, a pressure survey may take only 1 to 3 days while the corresponding quantity survey would require 1 to 3 weeks. Although this procedure would undoubtedly lead to more ac¬curate pressure measurements, its use for the development of computer input data is not recommended for the following reasons. Atkinson's equation, H = RQ2, is used in computer oriented analysis to develop the airway resistance, R, based on quantity and pressure loss measure¬ments. It can easily be seen that since R a 1/Q2 and R a H, the effect of errors in quantity measurement is, in fact, more significant than those in pressure measurement. If the quantity and pressure measure¬ments are made at different times another problem results. Minor changes in quantity that may occur in the time between the pressure and quantity

Jan 1, 1977

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By J. M. Oestreich

Supercritical water (sew) Is being tested for commercial use 1n several organic extraction systems but little work has been done on the extraction of metals from minerals. This lack of information prompted Bureau of Hines (BOM) research into the sew treatment of minerals. As a result, this research project is intended to serve mainly as a starting point for further experimentation. A simple flow-through reactor was built out of high pressure tubing and used to treat minerals with SCU at 400? C and 3500 to 7000 psi. The research produced four main conclusions: (1) carbonates of copper, iron, and lead convert to oxides; (2) most iron minerals showed alteration to oxides with some iron dissolution; (3) valuable trace elements including nickel, chromium, and others leached to some extent from sea minerals along with some calcium, iron, silicon, and sulfur; and (4) treatment of sulfides extracted elemental sulfur and resulted in several alteration reactions, though with the exception of cinnabar and the iron bearing minerals, the metals in sulfides were mainly insoluble. Surface alterations on many of the minerals show significant changes have occurred in the minerals even when only minor extractions were detected. These surface effects may be very important when used in conjunction with flotation processes since the sew treatment may selectively enhance or suppress a mineral's floatability.

Jan 1, 1989

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By L. R. Burdick

This paper presents a review of published investigation dealing with the importance of sulfur compounds in the deterioration of materials or providing some basis for estimating the extent of loss shareable to such air pollution. Materials included are cement, stone, metals, paint, leather, paper, sand cloth. The investigations may be divided into two classes, one of the laboratory type in which the sulfur content and the humidity of the air were controlled and the other dealing with the exposure of materials to atmospheres not under control. The first type of work has shown that cement is subject to deterioration by the action of sulfur dioxide gas. The experiments with stone indicate that although limestone takes up sulfur dioxide, from the air, moist sulfur dioxide-air mixtures alone cannot be used for establishing- the comparative weathering- qualities of the different types of stone by accelerated test methods. Laboratory tests indicate that sulfur compounds in the air accelerate the corrosion of iron, steel, zinc, copper, and nickel at normal air temperatures and at certain relative humidities. It has also been indicated that certain types of paint are, affected by high sulfur dioxide concentrations, and that paper is attacked by sulfur dioxide in the atmosphere. The investigations of the second type show the amount or variation of corrosion in different localities and under different types of exposure. The investigations (10) (18)4/ during which sulfur determinations were made indicate that sulfur dioxide is a main controlling factor in the corrosion of iron and steel but according to Quick (18) may not be for some nonferrous metals. In general, the laboratory tests do not Jive definite data on the loss due to sulfur compounds at the concentrations normally found in the air. The data from atmospheric exposures are not complete from the standpoint of the exact effect of the sulfur compounds. Damage to materials so exposed is affected by factors such as other chemical contaminants, humidity, rainfall, solid deposits, and sunlight. A simple scheme has been devised in Great Britain which is considered to provide a measure of the attack of sulfur compound, on building materials (1). Small cylinders coated

Jan 1, 1939

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire in¬juries that occurred in underground coal mines by state during 1990-1999. Table 1 also shows by state the risk rates, employ¬ees' working hours, lost workdays, and coal production. Over¬all, 87 fires occurred in 12 states. Twenty-seven of those fires caused 34 injuries (the yearly average was 8.7 fires and 3.4 injuries). One fire and one injury involved a contractor. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations followed by 13 mine/section sealing/flooding/CO2/N2, gas injections. The Ewhr value was 1,003 x 106 hr (In = 0.007), the CP value was 4,008 x 106 st (Frr = 0.022), and the LWD value was 208. Virginia had the most fires (15 fires and 7 injuries). Pennsyl¬vania had the most fire injuries (12 fires and 9 injuries), fol¬lowed by Kentucky (12 fires and 6 injuries), and Alabama (12 fires and 4 injuries). Among these states, Alabama had the highest fire risk rate value (Frr = 0.073), whereas Pennsylvania had the highest injury risk rate value (In = 0.016). Table 2, partly illustrated in figure 2, shows by time period the number of fires, fire injuries, risk rates, employees' working hours, lost workdays, and coal production. The number of fires and fire injuries show a decrease followed by an increase during the five time periods (see table 2 and figure 2). This was ac¬companied by a decline in employees' working hours throughout the periods and an overall small decrease in coal production. The In and Frr values follow patterns similar to those shown by the fire and injury values. By comparison, data from Pomroy and Carigiet [1995] show that during 1978-1992 a total of 11 states were involved in 164 underground coal mine fires (yearly average, 10.8) with 43 injuries (yearly average, 2.9) and 27 fatalities (yearly average, 2; however, the 27 deaths occurred during a single fire caused by an overheated air compressor [MSHA 1984]). The CP value was 5,340 x 106 st (yearly average, 356 x 106 st) (Fn = 0.031). Data on employees' working hours and injury risk rates were not available. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables during 1990-1999. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962