Search Documents

By Lung Cheng

The Bureau of Mines conducted laboratory tests to investigate the ease of frictional ingition with frozen (nonrotating) conical bits cutting into sandstone. The number of strikes with a new bit to obtain ignition of a combustible methane-air environment was measured. Tests were made with bits tipped with both tungsten carbide and steel at several bit attack angles (angle between bit axis and sandstone surface) and initial tip angles (included angle at the tip of the new bit). Carbide-tipped bits required more strikes for ingition than steel-tipped bits, by a factor of 7 to 10. With a carbide-tipped bit, the number of strikes for ingition increased by a factor of about 3 if the bit attack angle increased by 10° or if the initial tip angle decreased by 10°. During use, abrasive wear of the frozen bit caused a flat surface to form at the tip of the bit, thereby decreasing the tip angle. As the attack angle increased, however, the new bit involved a smaller wear-flat area whereby, abrasive wear was decreased.

Jan 1, 1987

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By H. E. Powell

A solvent extraction procedure was developed on a laboratory scale for recovering trisodium phosphate, zinc, and iron from waste phosphate sludge as separate products. The sludge was dissolved in hydrochloric acid, and iron was extracted as ferric chloride by isopropyl ether. Zinc was extracted by di-2-ethylhexyl phosphoric acid in kerosine. The efficiencies of the one-and two-stage extractions ranged from 98 to nearly 100 percent. Trisodium phosphate was recovered by crystallization from the raffinate. The value of two marketable products is considerably more than than the costs of the major reagent. The process was developed to permit recycling of values in this waste and to consequently reduce stream pollution from this source.

Jan 1, 1972

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By Fred D. Wright

Some new equipment for drilling vertical holes, cleaning blast holes, hauling explosives, and conditioning Diesel exhaust gas has been developed. at the Bureau's Experimental Oil-Shale mine near Rifle, Colo, The equipment has application, not only in oil-shale mining, but in many of the country's underground mines in which room-and-pillar methods of mining are employed. This report presents the Bureau's experience in testing the following equipment in the Experimental Oil-Shale mine: 1. A four-drill benching jumbo for drilling 23-foot vertical blast holes 2. A jet borehole blower for efficient cleaning of deep, vertical blast holes. 3. An explosives truck equipped with two compartments to provide safe conveyance for dynamite and detonators. 4. A mobile, electric substation to provide switching equipment, low-voltage and overload protection, and transformer facilities to remote locations in the mine. 5. A chemical conditioner for scrubbing the exhaust gases from Diesel-powered equipment used in underground operations. 6. Other units of equipment which have been tested at the Experimental mine.

Jan 1, 1951

By G. S. Scott, G. W. Jones, I. Spolan, R. E. Kennedy

In studies made by the United States Bureau of Mines to determine the causes of explosions in medium-pressure acetylene generators , it was shown that when these are operated at elevated temperatures the acetylene liberated in an acetylene generator carries enough water vapor to heat certain types of carbides to a high temperature , when the acetylene- water vapor mixtures are passed through the carbide . This report contains results of further work carried out to develop an apparatus to show the heating effects or reactivity of various types of carbides in contact with acetylene - water vapor mixtures .

Apr 1, 1947

By C. A. Frenzel

Extensive spectroscopic data are needed in making reliable vibrational assignments for use in calculating thermodynamic functions of polyatomic molecules. The fundamental vibrations of organic molecules may be observed at any wavelength from 2.5 to 200 microns (micron = µ = 10-4 centimeters), but most often in the region from 3µ to 50µ. Raman spectra generally cover the range in which fundamental vibrations occur, but equally important infrared spectra usually are not measured at wavelengths longer than 25µ. This limitation results because most infrared spectra are determined for analytical purposes, which seldom require information outside the region 2µ to 25µ. Measurements of infrared spectra in the range 15µ to 35µ recently were begun by the Bureau of Mines to obtain data needed in making vibrational assignments. This report presents the spectra of the following thirteen compounds: Tetrahydrofuran, 1-methylpyrrole, piperidine, 2-methylpyridine, 3-miuthylpyridine, 2-propanethiol, cyclopentanethiol, 2-methyl-2-butanethiol, 3,3-dimethyl-2-thiabutane, cyclohexanethiol, cyclopentyl-l-thiaethane, 2,4-dimethyl-3-thiapentane, and hexamethyldisiloxane.

Jan 1, 1960

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By A. B. Needham

This paper, which describes mining practices at a mine in the Cave- in-Rock, Illinois, fluorspar district, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. Ore deposits in the southern Illinois-western Kentucky fluorspar dis- trict are of two general types (1) the flat-bedded, lenticular replacement and (2) the relatively narrow, rather steeply dipping fault or fissure filling. This paper describes production methods used and results obtained in mining one of the bedded lenticular ore bodies that are prevalent in the northeast portion of the district near Cave-in-Rock.

Aug 1, 1949

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By C. J. Walker, Ray V. Huff

The feasibility of inert - gas cushions in underground gas storages was studied by the Bureau of Mines in accordance with a continuing program of cooperative research between the natural gas industry -- through the American Gas Association . As mixing of the inert - gas cushion with the stored natural gas is undesirable , the various mechanisms tending to bring about such mixing were the subjects of both theoretical and experimental studies . These studies indicated the practicability of such cushions is dependent upon both reservoir and operating conditions . Equations and tables of illustrative data relating the various reservoir and operating conditions to the expected time required for undesired mixing to occur in ideal reservoirs are presented . This information permits estimating the relationship of such factors in actual storage operations .

Jan 1, 1964

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent to as high as 20.5 per cent by volume. Hydrogen sulphide is probably the most toxic gas associated with natural gas, and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphj.de, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free sulphur and water. The free sulphur will dissolve in the gasoline produced by any of the aforementioned methods and cause the product to be positive to the corrosion test and there-fore unsuitable for commercial use in that condition. The objectionable sulphur compounds can be removed by washing the gasoline with a solution of caustic soda or other chemicals, but this treatment is expensive. It is advantageous therefore to remove the hydrogen sulphide from the gas before it is processed in a natural-gasoline plant.

Jan 1, 1932

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1362 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964