Search Documents

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By Robert M. Busche

[Recent developments in the gasification of coal, both by the Bureau of Mines and American industry, have intensified interest in the thermodynamic and kinetic principles necessary for understanding the reaction mechanism and rates and the physical changes that take place. In the course of a Bureau of Mines study of the kinetics of coal gasification at the Synthetic Liquid Fuels Demonstration Plant, Louisiana, Mo., a bibliography of approximately two references was compiled. They are listed n this publication and refer both to American and foreign sources.]

Jan 1, 1952

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility is evident from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well- administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"DIGREGORIO, K. A., E. V. CILENTO, AND R. C. LANTZ. A kinetic model of superoxide production from single pulmonary alueolar macrophages. Am. J. Physiol. 256 (Cell Physiol. 25): C405-C412, 1989.-A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared with experimental results obtained from single rat PAM. The 02 was quantified by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate (NBTH,) from video-recorded images of individual cells. The kinetic model considered three reactions: 1 ) the production of extracellular 02 from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, 2) the subsequent dismutation of 02 to form H,O,, and 3) the reaction of 02 and NBT to form diformazan. NBT specificity for 02 was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) that catalyzes the dismutation of 02 to H,O,. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations because NBT is a relatively small molecule (818 mo! wt) compared with SOD (34,000 mol wt). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/ or electrostatic effects, since SOD is also negatively charged, whereas NBT is positively charged.PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria. This process is accompanied by the production of superoxide anion (02) at the surface of the plasma membrane (3, 31). Superoxide readily dismutates to form H20 2 and subsequently, other oxygen metabolites which have been shown to be both antibacterial and cytotoxic (21, 25, 35).Superoxide is produced from the reduction of extracellular O, at the surface of the cell membrane by NADPH oxidase by the following reaction (3, 4)"

Jan 1, 1989

By L. C. Brichta

The Tri-State zinc-lead catalog, compilation of which was initiated by the Bureau of Mines in August 1949, is designed to provide a continuing record of avail-able drill-hole logs and maps of mine developments in the zinc-lead district in southwestern Missouri, southeastern Kansas, and northeastern Oklahoma. The maps and data thus preserved constitute a reservoir of factual information readily available to individuals and firms interested in planning mineral explorations, to Government agencies for formulating estimates or ore reserves, and to the mining industry in the district for general uses. The areas to be included in the catalog embrace the explored and mined tracts within 760,000 acres of the more active western part of the district. The consensus among local mine operators, geologists, and mining engineers is that over 100,000 boles, costing more than $30,000,000, have been drilled in the district. Records of some of the early drilling and mine developments are destroyed or lost, but the Bureau of Mines has copies of about 47,500 drill-hole logs and is accumulating and recording on microfilm those that are currently available. As of May 1, 1954, the logs of approximately 28,000 drill holes had been microfilmed and are available for inspection at the Bureau of Mines office, Joplin, Mo.

Jan 1, 1955

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By Verne E. Hooker

In situ stresses, based on isotropic and anisotropic relations, were evaluated using computer techniques from overcoring data obtained in dimension stone quarries along the Appalachian Piedmont, the Ozark Uplift, and the Ouachita Tectonic Belt. Stresses in the horizontal plane near the surface are compressive and range from 100 to 4,500 psi. The direction of maximum compressive stress seems to be alined with the general tectonic structure for most of the determinations. The ratio of the maximum to minimum elastic parameters in the horizontal plane ranges from 1.05 to 2.46 for these competent rocks. Isotropic versus anisotropic stress determinations show differences only as great as 25 percent in stress magnitude and 25° in orientation.

Jan 1, 1969

By J. D. Davis

THE CARBONIZING properties of Chilton-bed coal from Lorado No. 5 mine, HE Logan County, W. Va., were determined by Bureau of Mines-American Gas Association tests at 600°, 700°, 800°, 900°, and 1,000° C. and by expansion tests. Chemical analyses, agglutinating and plasticity tests, and low- and high-temperature assays also were included in the investigation. Blends with low-volatile Pocahontas No. 3 coal were carbonized at. 900° C. The Chilton coal bed lies in the Kanawha, or Upper Pottsville formation of the Pennsylvanian system; the estimated original reserves are nearly 3.2 billion tons. The bed was 39/1 to 57 inches thick in the Lorado No. 5 mine, and the coal was 38 to 57 inches thick. The carbonization sample contained 62.6 percent fixed carbon on the dry, mineral-matter-free, basis, and the heating value on the moist, mineral-matter-free basis was 15,190 B. t. u. per pound; it therefore ranks as high-volatile A bituminous. It contained 1.8 percent moisture, 35.2 percent volatile matter, 57.9 percent fixed carbon, 5.1 percent ash, and 0.7 percent sulfur, as carbonized. The sulfur was largely organic, and the ash softened at 2,630° F. The agglutinating value determined on a silicon carbide-coal mixture of 15:1 was 6.8. In the Gieseler test the coal softened at 327° C., fused at 407° C., attained a maximum fluidity of 5,730 dial divisions per minute at 435° C., and solidified at 487° C. Maximum resistance in the Davis plastometer was 45.5 pound-inches.

Jan 1, 1951

By C. Golumbic

Most early research on solvent extraction of coal has been concerned with the molecular structure of coal. Although rush work is continuing, practical aspects of the subject also are being emphasized. For example, development of the Pott-Broche extraction process resulted from the discovery of very efficient solvents for the pressure-extraction of coal. Recently, Orchin and Storch reported the use of even more efficient solvents under similar conditions. In addition to the discovery of more effective solvents, the possibility of efficient extraction at atmospheric pressure is obviously of practical interest. H. J. Rose observed that phenanthrene at its atmospheric boiling point readily dispersed 80 percent or more of Pittsburgh-bed bituminous coal. This fact served as the starting point of the present investigation, ill which determination of the chemical specificity of this solvent and the chemical nature of the resulting extracts was undertaken. This paper represents a progress report of the results obtained to date.

Jan 1, 1950

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

By J. J. Shields

The Bureau of Mines observed two different types of longwall mining; the advancing longwall method and the retreating longwall method at seven bituminous coal mines located in five of the coal producing states. In two mines using the advancing face method, the coal faces were abandoned because of roof failures and poor production. In the other five mines using the retreating method, roof control was good as was production. The success of longwall mining depends on good roof control and good production. The use of self-advancing hydraulic roof supports, such as Westfalia, Dowty, and Wanheim props along with Westfalia coal planers and the Anderton and Eickhoff shearer-loaders have been a factor in recent successes.

Jan 1, 1967

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By John A. Ruppert

1. It has been proposed that the addition of enough limestone to an open -hearth s lag to give a CaO-3P2O5 ratio of approximately 2-followed by SiO2 firing in an oxidizing atmosphere under the proper conditions of time and temperature will result in a clinker having a magnetic phase containing a preponderance of Mn, Fe, Al, and Mg as oxides and a nonmagnetic phase consisting for the most part of a phosphorus-containing dicalcium silicate. It has been postulated further that the metal oxide phase can be recovered by fine grinding and magnetic separation. These broad principles have been substantiated by numerous clinkering operations made in an electrically fired studio-type kiln, a batch rotary kiln, and a continuous rotary kiln and by magnetic separations made in a Davis -tube separator and a laboratory-size Jeffrey-Steffensen three -roll continuous separator. 2. Quenching the clinker after firing seems to improve its grindability. Microscopic examination of the ground clinker indicates .that the oxide phase grinds down at a somewhat faster rate than the silicate phase. 3. Very fine grinding is necessary to approach liberation, of the oxide phase from the silicate phase. Grinding to ininus-325-mesh, followed by magnetic separation, gave only a rougher concentrate, which had to be reground before final separation. 4. Although the manganese content of the final concentrate was higher, there was some evidence that manganese recovery was lower from a clinker made from a flush s lag than one made from a mixture of tap and flush slags. A possible explanation is that a clinker made from a mixture of slags has a higher iron content and hence is more magnetic and more easily separated.

Jan 1, 1952

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By Pamela J. Watson

A novel technique has been employed by the U.S. Bureau of Mines to determine the zeta potential of particles for a far-reaching series of material types in a wide variety of baseline waters, both alone and with many different chemical additives. The materials tested ranged from naturally occurring Sioux Quartzite and Tennessee marble to commercially produced magnesium oxide bricks. The waters tested ranged from ultrapure distilled, deionized water to municipal tap water and mine-site water. The chemical solutions tested included inorganic additives, such as aluminum chloride (AICI3) and sodium chloride (NaCl); organic additives, such as dodecyltrimethyl ammonium bromide (DTAB); and nonionic polymers, such as polyethylene oxide (PEO). The results of precise zeta potential determinations have application in a large number of laboratory studies as well as in various mining and processing operations.

Jan 1, 1989