Search Documents

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By L. C. Zhou

The floatability of andalusite and associated minerals are studied and their action mechanisms of andalusite and associated minerals with collector alkyl benzene sulphonate are also studied. Through the mensuration of electrical potential and the infrared spectroscopy, as well as desorption tests, it is confirmed that the interaction of andalusite with sodium dodecyl benzene sulphonate (SDBS), is in addition to physical adsorption, but also is chemical adsorption. The study results of the pure minerals are used for the flotation of actual andalusite mineral. By flotation from contain-ing 45.68% andalusite ore, the fine andalusite concentrate is gained which Andalusite grade is 85.88%, containing Al2O355.29% and Fe2O3 less than 1.5%.

Jan 1, 2014

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By D. DePaoli, P. Zhang

"Phosphate ore is one of the most significant secondary resources for rare earth elements (REEs), and Florida phosphate is of particular interest due to its much higher ratio of heavy REEs, especially yttrium. Analyses of numerous samples from different phosphate processing streams in Florida showed that heavy REEs account for about 50% of the total REEs in Florida phosphate with yttrium accounting for approximately 30%. It was estimated that the amount of yttrium from US phosphate processing could meet the world demand for this critical element. This research aimed at recovering both REEs and phosphorus from a phosphate flotation tails. This tails is composed of mainly silica and phosphate with a small fraction of heavy minerals including monazite and xenotime. Since the specific gravity of silica is 2.6 versus 3.2 for phosphate and 4.5-5 for rare earth minerals, pre-concentration of the minerals of interest by gravity separation was investigated first. A pilot scale shaking table was used in this study. One pass gravity concentration achieved a shaking table concentrate analyzing over 600 ppm REEs at about 40% recovery. Flotation of the shaking table concentrate resulted in a product containing 1809 ppm REEs and 26.37% P2O5 with corresponding recoveries of 73% and 82%. Sulfuric acid leaching at 75oC could recover over 60% REE and nearly all the P2O5. Higher REEs (>90%) recovery was achieved by conducting leaching at higher temperature with concentrated sulfuric acid. The phosphoric acid from leaching of the flotation concentrate is of superior quality compared with that generated from regular phosphate rock.INTRODUCTION Rare earths are a group of 17 elements including those of the lanthanum series, as well as the non-lanthanides, yttrium and scandium. These elements have very specific critical uses in a multitude of markets. For example, lanthanum is used as a catalyst in breaking down crude oil to produce gasoline, diesel and jet fuel and neodymium is the core magnetic component in high-strength magnets for electric car batteries, wind turbines and hard disk drives. Rare earths are also essential for many military applications. Many of these applications have no substitute materials and the move to green technologies has dramatically increased their demand."

Jan 1, 2018

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By K. Kiangi

On installing the Metso Superior MK 54x75? primary gyratory crusher in Nkomati mine the crusher experienced severe power spikes greater than 1000kW which subsequently led to the crusher tripping under load while processing some of Nkomati?s MMZ ores. Likewise significant losses in throughput were also experienced while processing some of Nkomati?s MMZ ore types. Interestingly the crusher was capable of processing the PCMZ ores without experiencing any power spikes or losses in throughput. Investigations into the challenges faced by the crusher while processing Nkomati?s MMZ ores were conducted using the DEM model in conjunction with the fast breakage model present in Metso?s High Fidelity Simulator. The intentions of the study were to establish the most suitable operating conditions or cavity design that would potentially enhance the performance of the crusher. Likewise an understanding of the effects the feed conditions (size distribution and hardness) had on the crusher?s performance was established. Ore characterization tests were conducted on Nkomati?sPyroxenite, Diabase, Calc silicate and quartzite ores which were from Nkomati?s MMZ ore body. The ore characterization tests conducted were drop weight tests, slow compression tests and elastic modulus tests. Four simulations were conducted used the existing cavity design with various open side settings (OSS) and throws. This established the effects of changing the crusher?s operating conditions on its performance. Four additional simulations were conducted on two cavity designs with reduced volumes. This established the effects of changing the crusher?s cavity design on the crusher?s performance. Thus through the simulations a better understandings of the impact of the crusher design, operating conditions and feed conditions on the crushers performance. Furthermore an analysis of the crusher?s performance was made which was used as a basis for comparisons with the base case simulation. Keywords: crusher, discrete element method, simulation, ore characterization

Sep 1, 2012

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By J. Y. Tian

In view of the fact that many domestic iron ore-dressing plant applying flotation cells in the re-verse flotation, to improve the technical level of magnetite reverse flotation, we apply such a technological process of one stage rougher and two stages scavenger flotation column respectively. The middling from the two stage scavenger process are returned to magnetic separation for condensing. By contrast, the technological process of one stage rougher and one stage cleaning flotation cells is made up of by multi-magnetic separation and magnetic middling regrinding separations. It has been proved that the flotation column we offer can simplify the technological process structure, obtain advanced technical indexes, run the system smoothly, reduce energy consumption, and be environ-mental friendly.

Jan 1, 2014

By G. R. Forbes

Flotation froth machine vision systems provide consistent real-time measurements pertaining to the state of the flotation cell being monitored. Typical measurements include froth velocity, froth colour, froth texture and froth stability. This paper presents the results from test work conducted on the molybdenite rougher circuit at the Kennecott Utah Copper Concentrator during February 2006. Machine vision results show that it is not possible to accurately determine bubble size distribution information for the molybdenite froth, despite using state-of-the-art methods. Instead, it is necessary to make use of texture measurements to classify the various different froth states. Numerous combinations of texture measurements and classifiers are used to determine the best combination. Results show that the Fourier ring based texture measurements perform the best when both K nearest neighbour and Gaussian mixture model classifiers are used. The concentrate grade of the flotation cell is modelled using combinations of froth velocity and froth texture descriptors. The results show that by using a linear combination of these descriptors rather than either one by itself it is possible to account for a much larger percentage of the variation observed in the concentrate grade data. Adjusted R2 values of 92% and 84% are achieved when modelling the copper and the molybdenite concentrate grade respectively.

Jan 1, 2014

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By Charlene Gokhale

Geopolymerisation has emerged during the last few years as an industrial and ecological approach to construction and waste management. By utilizing waste materials and their reactive properties, it is now possible to create geopolymers systems that not only mechanically durable enough to be used as construction materials but are also potential stable immobilisation systems for toxic waste. Previous studies by Van Jaarsveld et al. (1997) and Van Jaarsveld et al. (1998) have reported on the numerous applications of geopolymers in the immobilisation of toxic metals. Research into the possible utilisation of geopolymers as an encapsulation media for organic waste has however been rare. This paper therefore provides an insight into the possible utilisation of geopolymers as a binder for hazardous organic materials.

Jan 1, 2003