Search Documents

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By Timothy C. Siegel, Derrick Dasenbrock, Rich Lamb, Paul J. Axtell

"The axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top loads, and whether the top load is sustained, transient, or a combination of sustained and transient loads. Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the AASHTO LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines the current AASHTO Specifications and presents an alternative design approach for drag load and downdrag using the LRFD framework. The alternative design approach is illustrated by two examples involving drag load and downdrag.IntroductionThe axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top load, and whether the top load is sustained, transient, or a combination of sustained and transient.Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines current LRFD design specifications and presents an alternative design approach for drag load and alternative design approach is applied to several examples where drag load and/or downdrag may control design."

Jan 1, 2015

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By Julie Clarke

In 1939 Dr. Ralph Peck criticized the Civil Engineering community for taking a bifurcated approach to the prediction of building damage due to subsurface geo-technical works. Specifically, he observed that Geotechnical Engineers concerned themselves only with subsurface issues implying that their results were largely independent of the presence and condition of the structures above. He continued that Structural Engineers charged with risk assessment of buildings approached their work nearly in isolation of below ground activities. Seventy years later, although the state-of-the-art has enabled a better understanding of soil-structure interaction, the reality remains that risk assessment from subsurface construction, is not yet an integrated activity when done on a large-scale basis. To help move beyond this, this paper proposes a new, integrated methodology for preliminary assessment that considers a three-stage process that involves the following: (1) traditional empirical relationships for predicting ground movement from tunneling, (2) recent advances in condition assessments, and (3) architectural designators related to usage and historic preservation listings. The methodology is applied to a study area of nearly 260 buildings in the city center of Dublin Ireland, in an area slated for an upcoming metro. The results are com-pared to the Environmental Impact Statement issued for the official project. Al-though the test case is for tunneling, the approach may be adapted to other subsurface construction activities including excavation and piling.

Jan 1, 2009

By Bernardo J. Jiménez, Harlem Lora, Roberto Acosta Mora

Circunvalacion Norte project is currently the most important infrastructure project in Costa Rica. It is the last segment of the urban perimeter highway. Site investigation of local geotechnical conditions were studied by SPT, CPT, pressuremeter tests and boreholes. A static load test was executed as a proof test with an associated ultimate resistance of 12056 kN (2710 kips). Drilled shaft design was done using PMT tests and axial nominal resistance varied between 4000 kN (900 kips) and 6000 kN (1350 kips). A total of 416 drilled shafts were constructed in 15 months with drill performance of 32 m/day (105 ft/day). Drilled shaft lengths varied between 4,0 (13 ft) m and 40,0 m (130 ft). Selfconsolidating concrete was used to achieve an adequate workability even in high densities rebar cages. Several site conditions proved the importance for maintenance of the working platform, predrilling of rock sockets and having spare parts to avoid increase in project’s cost. New procedures were taken to prevent concrete segregation on excavations near underground water flow. Monitoring the quality of the shafts from CSL test showed less than 3% of the shafts presented a considerable anomaly, which proved that the adopted construction method and materials were adequate. For the concrete anomalies, successful remediation was performed by means of grout at the base of the shaft with two different types of drilling methodology depending on the concrete anomaly.

By Arash Khosravifar, Amalia Giannakou

"Nonlinear foundation springs for bridge caisson foundations show significant coupling between the shear force and bending moment. Implementing foundation stiffness matrix with coupling effects (off-diagonal components) into the global bridge model presents numerical challenges. A simplified approach is developed to model foundation springs including coupling effects using a simple methodology. This simplified model include one translational spring and one rotational spring combined with a rigid link in 2D space. Results show that nonlinear springs (translational, rotational and coupling) can be reasonably captured using this simplified procedure.INTRODUCTIONThe Izmit Bay Bridge is a 3-km long suspension bridge that crosses Izmit Bay in Turkey and is being constructed in a highly seismic region. Figure 1 shows the project location. The South Approach Viaduct (SAV), located along the western margin of Hersek peninsula, is within 5 km from the North Anatolian Fault and within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The proposed SAV consists of 11 Piers and an abutment at the south end of the structure."

Jan 1, 2017

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019