Search Documents

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988