Search Documents

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By W. Dolsak

Introduction Alternative bolting injection resin Hollow bars, rebars, and cable bolts Results from an in-house product development project Sept. 2011 to Feb. 2013 Goals Introduction of a newly developed bolting silicate injection resin as alternative to cement grout based injection systems Definition of easy-to-use pumping devices and installation accessories Accomplishment of installation trials and performance evaluation

May 1, 2013

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By M. E. Holter

"Three main potash members are recognized within the Prairie Evaporite Formation of Saskatchewan and have been designated, in ascending order, the Esterhazy, Belle Plaine and Patience Lake members. Each is composed of sylvinite near the geographic center of the member and becomes increasingly carnallitic marginally. Each stratigraphically higher member has a narrower carnallitic margin. The sharp contact between carnallitic and non-carnallitic components of the formation describes a surface which may be traced regionally and is not related to bed-ding. The contact rises higher in the stratigraphic section toward margins of members. Within each of the three members, analyses indicate that carnallite becomes more abundant toward the north whereas sylvite and insolubles, increase toward the south. Within each member, areas rich in carnallite are coincident with areas in which the member as a whole is thicker than averag,e. The Belle Plaine Member contains the highest concentrations of carnallite, the Esterhazy the lowest. A maximum content of about 30 per cent sylvite is common to all three members. Insoluble contents increase in successively higher members.Map studies are combined to outline the economic potential of the potash beds in terms of depth to the top of the Prairie Evaporite, ""salt-back"" thicknesses and sylvite grades for each member."

Jan 1, 1971

By Weldon Li

Outline ?Introduction and Motivation ?Previous Research ?Details ?Findings ?Current Multi-Piece Mining Wheel Research ?Methodology ?Preliminary findings ?Current and Future Activities ?Summary and Closing Remarks

Oct 1, 2010

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By R. A. L. Drew, F. Jalilian, M. Jahazi

Joining of superalloy Inconel 61 7 with a foil interlayer using transient liquid phase bonding (TLP) technique was studied. Inconel 617 is a solid solution, Ni - Cr - Co- Mo alloy with an exceptional composition of high temperature strength, oxidation, carburization resistance and thermal stability. In this investigation, two bonding temperatures, 1065°C and 1150°C, and two interlayer thicknesses with joining times varying from 5 minutes to 24 hours were employed. Experiments were carried out using nickel base interlayer (A WS BNi-3) with boron as the melting point depressant (MPD) element. Joints were characterized using optical microscopy, SEM, FEG-SEM, EBSD, XRD and microhardness. The results indicated that the rate of elimination of the liquid phase with increasing the bonding temperature, holding time and decreasing the thickness of the interlayer increased. The main precipitates in the diffusion layer had platelike and blocky morphologies for both bonding temperatures and all holding times.

Jan 1, 2006

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By B. Vorobyov

A Canadian company, Sight Power Inc., has developed a revolutionary, fully automated shaft monitoring and inspection system for deep-level mining based on a 3D mobile laser scanning technology. It consists of a special hardware unit and proprietary software with Artificial Intelligence elements for object recognition, features identification and change detection. The main purpose of this system is to significantly improve the safety of underground mining as well as to increase the available hoisting time thus generating substantial additional revenue for the mine.

Aug 1, 2013

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By Samuel Nunoo

Gibraltar Mine is an open pit copper-molybdenum mine in central British Columbia. The stability and potential failure modes of pit walls in the Granite Pit are controlled by the orientations of joints and faults. The structural geology also has an impact on as-mined bench geometries. Geotechnical mapping and surveying were conducted using stereo photographs and photogrammetry software. Detailed digital terrain models were constructed to determine the pit wall geometry and the locations and orientations of larger structural features. The pit wall geometry is compared to conventional survey results and the mapped structures are compared to results from a nearby geotechnical borehole.

Aug 1, 2013

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994