Search Documents

By Yuki Soma, Tsutomu Ogawa, Jae Hyung Hong, Toshihiro Nagato

The Saganoseki flash furnace was built in 1973. The steel frames of the flash furnace were designed to absorb the expansion of refractories and contain expansion-absorbing materials between their frames and the skin plate. Expansion and deformation resulted in the furnace settler because of the repeated increase and decrease in temperature from more than 30 maintenance shutdowns. Preliminary investigations were conducted to confirm the condition of the settler, and it was found that partial cracks accompanied the expansion in the lower layer of the refractories. As a result, the risk of molten-matte leakage increased. Based on the above investigation, it was decided that the entire settler should be replaced by introducing a spring-displacement structure that was capable of maintaining the furnace integrity over an extended period. The difficult redesign and rebuilding of the Saganoseki flash furnace was accomplished successfully and safely in 76 days from September to December 2017, as planned. Because of various redesigns, the furnace was changed to a flash-smelting furnace that can withstand higher thermal loads based on recent trends of copper concentrate with increased sulfur and reduced copper. The new furnace is operating smoothly at present. INTRODUCTION The flash-smelting furnace of Pan Pacific Copper Co., Ltd. Saganoseki Smelting & Refinary commenced operation in 1973, with an original designed feeding rate of 71 t/h. As a result of facility remodeling and operational improvements, shown in Figure 1, the feeding rate was increased to 215 t/h in recent years. After more than 40 years of operation, the original settler in the melt holding section of the flash furnace underwent significant expansion and deformation.

Jan 1, 2019

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By L. Becze, B. Pierre, S. Di Carlo, G. P. Demopoulos

From January to June 2007, the autoclave production at the Kidd Metallurgical Site was severely affected as a result of plugged discharge lines and extensive precipitation/crystallization of sulphates that caused massive scaling in different autoclave compartments. Work was performed at McGill University to understand the root causes. The crystallization of zinc and ferrous sulphate salts was investigated in terms of solubility measurements. Scale samples were characterized using chemical and mineralogical-spectroscopic analysis. In this paper, following a description of the Kidd zinc pressure leach operation, highlights from this investigation are presented and solutions used to overcome the problem are outlined.

Jan 1, 2008

By D. L. Marchioni

"The detection and quantification of the degree of weathering is an important aspect of coal exploration and mining. Tests for weathering which are suitable for the exploration camp should be fast, simple, and require minimal equipment and operator expertise. In this study, two tests which fulfill these requirements were evaluated using samples of Western Canadian coals. These tests, one based on the pH of a coal slurry and the other on the flotation of coal in a water/diesel oil mixture, do not appear to give consistent results and are not recommended as ideal weathering parameters.IntroductionThe weathering of coal results in a deterioration of those properties which render it suitable for use in industrial processes. Consequently, the detection and quantification of the degree of weathering is an important aspect of exploration and mining. Frequently, decisions related to the depth of the weathered zone must be made at the exploration camp and, therefore, tests for weathering which are fast, and require relatively inexpensive and portable equipment and minimal operator experience, would be very useful. The aim of the study reported here was to evaluate two tests used by U. S. Steel Corp. to detect coal weathering and which satisfy the requirements for use in an exploration camp. The study is a continuation of a more extensive examination of the detection of coal weathering by various methods, reported elsewhere (Marchioni, in press)."

Jan 1, 1981

Concentrator Improvements -1990-1995Back to Basics ?pilot plant versus plant opportunities identified ?understand process fundamentals & baseline -1996-2000Point ?C?Projects ?strategy to improve global competitiveness ?structure implemented to generate & drive ideas ?capital investment for life of mine asset renewal - 2001-200?Six Sigma Methodologies ?emphasis on data, measurements & analyses ?dedicated, highly trained personnel on projects 1990-1995 Improvement Phase??Philosophy??back to basics?approach?understand what each piece equipment needed to do?understand reagents, control variables?confirm operating strategies ??probe, stabilize, institutionalize??test theories, confirm with lab and plant trials?process stability (equipment reliability, controls)?enhanced operator guidelines, operator training?focus on continuous improvement?optimize existing equipment capability?stop looking for ?magic?solutions 1990-1995 Improvement Phase??Technical?finer grind, same equipment?optimize media size/shape to grinding application?balanced available ball mill power to applications?lowered cyclone feed densities where possible?improved selectivity, same equipment?balanced available cells to applications?streamlined process (eliminate process steps)?added cleaning stages where required?understanding pulp/mineral surface chemistry?lowered flotation pulp densities 1990-1995 Improvement Phase??Effort?numerous studies to understand process?liberation and mineralogical characterization?pulp and mineral surface chemistry?flotation kinetics and entrainment?extensive internal and external manpower?Brunswick, Noranda Technology Centre?CanMet, AMTEL, MinnovEx, Lakefield Research, McGill University?small capital expenditure

May 1, 2002

The effect of long term exposure of full size bolts to corrosive environments is presented. A special test rig was used to test four bolts under different loading conditions. Four, X-grade identical profile bolts, each of 21.7 mm core diameters (23.7 mm full diameter) were subjected to prolonged corrosion testing using acid sulphate water. The pH value of the circulated water varied between 3.4 and 4.3. The corrosion exposure test period lasted three and half years. Two bolts were axially loaded to 10 and 20 tonnes force respectively, the third bolt was subjected to a 360 Nm torsion load and the fourth bolt was left unstressed to act as a reference bolt. After the test period ended, the bolts were stripped of their corroded coatings and weighted for weight loss. The diameter of each bolt was subsequently measured, and the loaded bolt samples were first tested non-destructively for tensile cracks and then tested for tensile failure. No cracks were found on post corrosion bolts tested non-destructively. The failure strength reduction on all four post-corroded bolts was significant, varying between 21% and 39%. The onset of corrosion was not confined to the targeted mid-section length of the bolt, however, the severest corrosion occurred at the anchored ends of the bolts.

Aug 1, 2013

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By R. W. Guill

"The Apex Mine is currently scheduled to be brought back into production by Hecla in the first quarter of1990. Its projected productivity rate will be exceptionally high for a small underhand cut and fill mine.The ore mined at the Apex Mine occurs within a pipe-like structure as a series of iron oxides containing both gallium and germanium, plus significant amounts of silver, zinc, lead, and copper.Ground conditions in and around the ore zone have dictated that unique approaches be utilized. To date, these have included a prototype 0.5 cu. yd diesel LHD, and the use of fibrous shotcrete in 4ft by 7ft headings, and the first pneumatically-placed cemented backfill in North America. Above all else, it is the combination of new technologies with a small and dedicated workforce which has allowed for the successful development of this ore body.IntroductionThe Apex Mine is an example of the typical small underground project. It has high grade, but low tonnage and is deposited in poor ground. In such cases, conventional planning and thinking generally results in an uneconomical evaluation and negative production decision. Fortunately, some unconventional thinking was allowed to take place during the planning and evolution of the Apex Mine development. The result now serves as an example of how such unconventional thinking can lead to the type of innovations described below.The job necessitated the development and use of new equipment and materials to execute a highly flexible underhand cut and fill mine design/pneumatic backfill concept, that must be constantly modified as different than assumed conditions become evident in and around the ore zone."

Jan 1, 1990

By Arash Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5 M tons. The underground mine has three active development panels and one longwall panel. The mining horizon is about 500 m below surface and strata liberate methane. Three surface-based blowing fans provide ventilation air. A ventilation survey and subsequent analysis was undertaken and a simulation model developed. Air heating during winter is essential to prevent freezing of pipelines and to lesser degree, for miner comfort. Air at all three intake shafts is heated using gas-fired heat exchangers. A strata heat study was conducted in one of the active panels to determine rock attributes. Tests included in-situ measurements of rock thermal conductivity and geothermal gradient. Continuously methane monitors have also been installed in an active development panel?s return drift. Ventsim ventilation software was used to aid the heat and contaminant simulation study. An exercise was also undertaken to gain some understanding of methane contaminant levels throughout the mine. It was further used to determine an adequate surface intake air heating rate and consequently the minimum natural gas consumption needed for winter intake air heating at the mine.

Aug 1, 2013

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By M. G. Rylatt, G. M. Popplewell

"Production from Canada's first diamond mine is planned for the last quarter of 1998. The climatic conditions and the variation in kimberlite types to be treated have lead to the development of a compact and flexible processing plant.High kimberlite moisture contents and winter temperatures below -40°C have dictated a process flowsheet with limited in-circuit storage to reduce materials handling difficulties. The latest developments in High Pressure Grinding Roll technology will be used to liberate the valuable diamond, reduce diamond breakage, and increase fines production to reduce the amount of material for down stream processing in the Heavy Medium Separation section.A varying heavy mineral concentrate yield has lead to the development of a final Recovery section that will incorporate Attrition Milling and Wet High Intensity Magnetic Separation for concentrate reduction. The latest developments in diamond X-ray sorting will be used to produce a final diamond concentrate for mechanical sizing, weighing and packing.Fine tailings thickening will utilise Deep Bed Compression type thickeners. This relatively new technology can produce;i) high underflow densities at low flocculant dosage rates, andii) clear overflowswith a smaller thickening area than conventional high-rate thickeners."

Jan 1, 1998

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014