Search Documents

By Oberlando Gonzalez, Claudia Serna, Andrea Alzate, Esperanza López, Maria Holuszko

This paper presents a systematic approach on gold recovery from electronic waste (e-waste) using ammonium persulfate. This process was developed as a response to the lack of hydrometallurgical systems capable of separating gold from its metallic substrate without material grinding, with minimum formation of pollutants, and achieving a lower reaction time. Computer memory boards, electronic processors and electronic pins and contacts were analyzed to determinate base metals (Ni, Fe, Cu) and gold (Au) using microwave plasma atomic emission spectroscopy (MP-AES). An aqueous commercial grade ammonium persulfate with oxygen and pressure was used to produce the persulfate anion (S2O82-) and the oxidative sulfate ion (SO42-), which partially oxidized and leached the base metals breaking the Au-Ni-Fe-Cu bonds and allowing gold to be recovered in its original non-leaching state. The influence of the oxidative parameters was evaluated using full factorial (FF) and central composite designs (CCD) with response surface methodology (RSM) and first and second order models were developed. Using RSM allowed to obtain a faster recovery of gold, minimizing the agent consumption. The findings presented suggest that optimized quantities of ammonium persulfate, oxygen, pressure, temperature and liquid solid ratio could be used for selective oxidization of the base metals and to extract more than 96% of gold from e-waste.

Jan 1, 2017

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By C. Jay Hodgson, P. J. MacGeehan, T. Sanders

"The orebodies of the Campbell and Dickenson mines are localized within an anomalously fissile and deformed zone that transects the eastern margin of a dominantly mafic volcanic complex close to its contact with a synchronously formed sedimentary basin containing clastic and chemical sedimentary rocks. The ore zones are mainly quartz-carbonate fissure veins and siliceous replacement zones formed during deformation and metamorphism, although there are some syn-volcanic exhalative ore zones in the mines. On a regional scale, the volcanic rocks have been affected by syn-volcanic spilitic alteration which has involved the leaching of Fe, Mg, Au and As from, and the addition of Na and variable amounts of Si to bleached zones enveloping primary permeable structures in the rocks. The leached constituents were deposited on the contemporaneous sea floor as iron-rich chemical sedimentary rocks. Although this alteration is not closely related, spatially, to the ore zones, it is characteristic of the general environment, and may serve to distinguish gold-prospective from gold-barren areas on a mining-camp scale.Closely associated spatially with gold deposits is a zone of feldspar-destructive alteration within which the volcanic rocks are characteristically feldspar-free, enriched in As, Au and to a variable degree in Si, and depleted in Na, Ca and to a variable degree in Mg, Fe and K. The alteration zone is also characterized by abundant, variably transposed, small quartz-dolomite to ferrodolomite veinlets formed during deformation and metamorphism, and includes, but extends outside of, the anomalously fissile zone hosting the orebodies. The alteration zone is interpreted to have formed syn-volcanically within the upper part of a major submarine hydrothermal discharge zone."

Jan 1, 1982

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By T. Urbancic, Eric von Lunen, G. Viegas, A. Baig

"The characterization of the failure process of induced fractures by hydraulic stimulation is fundamental to understanding the generation and evolution of the discrete fracture network within the reservoir. A more detailed analysis of the fracture mechanism can be a powerful tool for identifying fluid flow paths and proppant placement within the reservoir. For example, during the rupture process the energy release is partitioned into different physical processes for which the relative ratio is changed by the presence of fluids or rotations in the local stress field with relation to the frictional resistance in the fracture plane. Fractures occurring in the same host rock under the same stress conditions are expected to rupture similarly, independent of their size (self-similarity). Changes in the scaling relationships of fractures are indicative of a change in the failure process, host rock or in-situ stress. Correlation of failure process data with reservoir rock properties and the in-situ stress field will help identify regions within the reservoir with characteristic types of failures. Further correlation with hydrocarbon production data can be used to develop efficient treatment plans and production diagnostic tools.In this study we investigate the failure process of ~27,000 microseismic (M < -1) fractures induced during a hydraulic fracturing shale completion program in NE British Columbia, Canada by estimating static and dynamic source parameters, such as dynamic and static stress drop, radiated energy, seismic efficiency, moment tensor, fracture plane orientation, slip direction and rupture velocity. On average, the microseismic events have low radiated energy, low dynamic stress and low seismic efficiency, consistent with the obtained slow rupture velocities. Events fail in overshoot mode (slip weakening failure model), with fluids lubricating faults and decreasing friction resistance. Events occurring in deeper formations tend to have faster rupture velocities and are more efficient in radiating energy. Variations in rupture velocity tend to correlate with variation in depth, fault azimuth and elapsed time, reflecting a dominance of the local stress field over other factors.Further identification of spatial and temporal distribution of families of events with similar characteristic rupture behaviors, based on either rock formation, depth, source type, fracture plane orientation, stress drop, pad or proppant stage, may be used as a proxy for specific fracture network development and hydrocarbon production. This information may be used to determine reservoir properties, constrain reservoir geo-mechanical models with measured physical parameters, classify dynamic rupture processes for fracture models and improve fracture treatment designs. These will be the focus of future studies."

Jan 1, 2015

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary&apos;s river, is 3,700 feet. To th&apos;e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands&apos; appearance was investigated.

Jan 1, 2005

By F. Parada, R. Parra

"The neutralization process of SO2 from coal burning plants is a well-defined technology using limestone to form CaSO4 according to the following reaction: CaCO3 + SO2(g) + 1/2O2(g) = CaSO4 This paper presents the results of a study carried out to validate the option of capturing SO2 using gases from a non-ferrous smelter; SO2 content was up to 12% using a three-stage fluidized bed reactor. The difference in SO2 content affects equilibrium conditions and kinetics, rendering a direct extrapolation of the high efficiency achieved for low SO2 content impossible. The R&D program consisted of a laboratory study using a semi-pilot operation of a one-stage fluidized bed reactor and the construction and operation of a three-step reactor prototype. Results show that the reaction proceeds according to the unreacted core model that imposes a compromise between CaCO3 conversion and SO2 capture. For high SO2 capture, the calcine from the reactor contained CaSO4 and CaO. A complete capture of SO2 from gases with 8 vol.% can be achieved with a mean reaction time of two hours at 800°C."

Jan 1, 2007

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By C. Arson

"Optimizing hydraulic fracture injection parameters in order to maximize hydrocarbon extraction and to avoid extensive borehole spalling is still an open issue. In this paper, the Differential Stress Induced Damage (DSID) model is employed to simulate the anisotropic damage distribution around pressurized boreholes drilled in fractured shale. The loading path is purely mechanical: excavation and fluid injection are simulated by stress relaxation followed by pressurization. We investigate the effect of pre-existing fracture orientation, in-situ stress and injection pressure on the propagation of anisotropic damage during pressurization. Finite Element results indicate that (1) damage initiates and develops when the ratio of two in-situ stress component deviates from 1, and the magnitude of damage is proportional to this stress deviation; (2) For a given in-situ stress field, damage initiates for a certain threshold of injection pressure, and the damage zone extends as the injection pressure increases; (3) A pre-existing fracture only affects the damage zone locally; the orientation of that fracture does not affect the damaged zone, which is controlled by in situ stress and injection pressure.INTRODUCTIONHydraulic fracturing is used to increase shale permeability and to enhance hydrocarbon extraction. In order to maximize the extraction ratio and to avoid wellbore spalling and clogging during fluid injection, the parameters related to injection for each particular site need to be optimized. Therefore, it is necessary to clearly understand how shale responses upon excavation and pressurization.It is well known that breakouts grow in the direction of minimum compression and that plastic deformation around wellbores tends to arrest breakouts (Zoback et al., 1985). Laboratory acoustic emission tests revealed that fractures propagate along the direction of maximum compression stress, and fractures (breakouts) are surrounded by the Excavation Damaged Zone (EDZ), in which rock properties are weakened by the presence of micro cracks (Eberhardt et al., 1999; Martino et al., 2004). The anisotropy from orientated foliations and cracks may influence the development and propagation of fractures and breakouts (Everitt et al., 2004). Sonic televiewer logs proved that during hydraulic fracturing, fluid injection further alters the stress distribution (Evans et al., 2005). Shale natural fabric strongly affects the evolution of the EDZ around boreholes."

Jan 1, 2015

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By T. T. Chen

The iron- and elemental sulphur-rich residues generated during batch and continuous pressure oxidative leaching of Inco Limited&apos;s Voisey&apos;s Bay nickel sulphide concentrate at 150°C in sulphate-chloride media have been characterized by X-ray diffraction analysis and scanning electron microscopy. The residues produced during the continuous leaching of the pentlandite- and pyrrhotite-rich concentrate consisted predominantly of hematite and elemental sulphur, with minor amounts of goethite. Although the iron species generated in the batch leaching tests were similar to those formed during continuous leaching, the morphologies of the hematite and goethite particles were significantly different. In addition to the tiny spheroids and bubble-like particles, the hematite and goethite generated during batch leaching occurred as larger "hollow" shell-like particles that contained residual pentlandite or sulphur cores. Although the leach solution from which the iron oxides had precipitated contained 5-15 g/L sodium, sodium jarosite was detected only in trace amounts in a few of the leach residues.

Jan 1, 2006

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019