Search Documents

In several European countries, including Russia, it has become economically attractive to utilize peat as a fuel for power generation, the production of metallurgical coke, the production of fuel briquettes for the domestic market and low-Btu gas. Although the economic base and availability of energy supplies in Europe is much different than it is in Canada, regional economics here may warrant the development of peat as an alternative source of energy. Canadian peatlands cover several thousands of square miles and have historically been considered as waste land. Now, with the increasing costs of other energy sources, it is apparent that fuel peat should be re-evaluated as a potential energy resource. A nation-wide inventory of peat deposits has been prepared and reserves evaluated for some of these areas where field surveys have been carried out. The paper describes alternative mining methods developed to meet some of the various conditions encountered on virgin peatland . These mining techniques are generally based on current peat technology exercised in other parts of the world and would be applicable in some of the peat regions of Canada. Cost estimates have been prepared for peat production in regions of Canada, and the socio-economic aspects of a large-scale fuel peat operation are discussed. Several potential utilization schemes have been described, with particular emphasis on electric power generation. The paper makes recommendations for steps to be taken in the development of a fuel peat industry in Canada.

Jan 1, 1978

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By I. C. Christopher

Introduction The geology of the Cochen-our Willans gold mine has been described in reports by the late Dr. H. C. Horwood (1) in 1940 and by Dr. J. P. Nowlan (2) in 1947. Information from these and other (unpublished) reports has been incorporated in the present paper, together with some recent ideas regarding structural features which are at present being used to locate ore shoots. Location and History The mining claims of Cochenour Willans Gold Mines, Limited, occupy 705 acres in Dome township, on the east shore of Red lake opposite McKenzie island. Adjoining properties are those of McKenzie Red Lake Gold Mines on the west, Boymar Gold Mines on the north, Marcus Gold Mines on the east, and Martin-McNeely Gold Mines on the south. The claims of the original group were staked by W. M. Cochenour, Dan Willans, and H. G. Young, and the Cochenour Willans Syndicate was formed in 1928. Work was carried out by the Syndicate and several other companies during the next eight years with inconclusive results, due to the irregular occurrence of the ore. In 1936, Cochenour Willans Gold Mines, Limited, was incorporated and production was finally started late in 1939.

Jan 1, 1951

By Mehmet F. Taner

"Abstract - The East Sullivan Stock (ESS) is a small, composite felsic alkaline pluton of presumed late Archean age in the Val d’Or mining district. Three main facies have been distinguished: monzonite sensu stricto, porphyritic monzonite, and green trachytic porphyry. This monzonitic group of rocks is of relatively homogeneous composition with high abundances of Na2O, K2O, Ba, Sr, Rb, Zr, Mo and LREE. The alkaline ESS is distinguished from other igneous units in the Val d’Or mining district, such as the Bourlamaque Batholith, by relatively high concentrations of Ba, Sr, Rb, Mo, Cu and Au. The ESS hosts many base (Cu, Mo) and precious (Au) metal occurrences, including: (1) porphyry style Cu-Au-Mo disseminated sulfide deposits, (2) Cu-Au deposits in volcanic rocks near the ESS contact, and (3) pyritic gold mineralization in east-west trending shear zones. The ESS is well defined by concentrical zoning on the aeromagnetic vertical gradient color map, and displays four linear trends, which are assumed to be structural lineaments, at 035°-055°, 320°-300°, eastwest, and north-south. The main mineral occurrences related to the stock display a preferred spatial association with the east-west linear magnetic trends.The ESS is preferentially located along a major structure and was emplaced late in the evolution of the Abitibi subprovince like other felsic alkaline plutons. This stock is similar to late-tectonic mineralized felsic alkaline intrusions of the Kirkland Lake and Larder Lake mining districts in Ontario, and to the Allard stock in the U.S.A. which is associated with gold and base metal mineralization. Similarities also exist with younger alkaline plutons associated with Cu-Mo-Au porphyry deposits in the Canadian Cordillera, which formed in tensional tectonic environments. The felsic alkaline magma may have formed by partial melting of deeply buried supracrustal rocks, concomitant with the development of deep fractures such as the Cadillac Fault. In such an environment, hydrothermal solutions carrying remobilized metals from deep supracrustal rocks may have deposited gold and base metals in structural traps. Plutons similar to the ESS should be good targets for mineral exploration. Résumé - Le Stock de East Sullivan (SES) est une intrusion composite alcaline d’âge tardiarchéen, situé dans le camp minier de Val d’Or. Trois principaux faciès ont été identifiés: une monzonite sensu stricto, une monzonite porphyrique et un porphyre trachytique vert. Les données chimiques montrent que ce groupe des roches monzonitiques est relativement homogène en composition avec des concentrations élevées de Na2O, K2O, Ba, Sr, Rb, Zr, Mo et ETRL, définissant une suite alcaline typique. Cet alkalin stock peut être facilement distingué des autres unités géologiques de la région de Val d’Or, tel le batholite de Bourlamaque, par une concentration élevée de Ba, Sr, Rb, Mo, Cu et d’Au. Le SES contient plusieurs importants prospects de métal précieux (Au) et de métaux de base (Cu, Mo), incluant: (1) une minéralisation disséminée de type porphyre Cu-Mo-Au, (2) une minéralisation de Cu-Au dans les roches volcaniques encaissantes hôtesses près du contact et (3) une minéralisation d’or pyritique dans une zone de cisaillement de direction est-nordest. Le SES est bien défini sur la carte aéromagnétique en couleurs du gradient vertical par des zonages concentriques, où quatre linéaments structuraux ont été reconnus: 035°-55°, 320°-300°, est-ouest, et nord-sud. Les principales zones minéralisées spatialement associées au stock sont généralement situées soit près des linéaments magnétiques est-ouest, soit le long de ceux-ci.Le SES semble s’être mis en place le long d’une structure majeure, développée tardivement dans l’évolution de la Sous-province abitibienne, comme les autres plutons alcalins felsiques. Ce stock est similaire à la suite tardi-tectonique d’intrusions alcalines minéralisées des camps miniers de Kirkland Lake et de Larder Lake en Ontario, ou"

Jan 1, 1996

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

By Raymond Dallaire

The Humphrey's spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

By A. Alfantazi

Recently, titanium and its alloys have been the materials of choice for the liner and internal components of autoclaves used to extract Ni and Co from laterite ores. There have been many corrosion incidents ranging from localized attacks due to scale formation or welding, to damage caused by pockets of concentrated acid. Most of the literature focuses on methods to avoid the corrosion altogether. Little has been published to increase awareness of the chemistry at these conditions. For this paper, a literature review of the thermodynamics of titanium was undertaken to decipher the slew of information available. E-pH diagrams were constructed from select data and compared with the results of electrochemical experiments. Since nickel laterite leaching takes place in sulphuric acid, and in many cases chloride concentrations are very high, the Ti-H2O, Ti-Cl--H2O and Ti-SO4---H2O systems were considered.

Jan 1, 2004

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By Richard Wells

Peabody Energy is the largest pure-play publicly traded coal company in the world. We have been in business 129 years and like most of the coal mining companies in the United States, since 1969 the majority of our safety improvement efforts had been driven by compliance with the various versions of the Federal Mine Safety and Health Act and the supporting federal regulations. In 2004 Peabody Energy management came to the understanding that in order to achieve our goal of zero incidents, that focus must change. This paper will describe the elements of the journey we began at that point to make the transition to a behavior and systems-based approach to safety management and our efforts to win the minds and hearts of our employees. This journey is undertaken with the goal of making safety truly a way of life for all Peabody Energy employees.

Aug 1, 2013

By A. J. Oliver, C. E. O’Neil, I. J. Itzkovitch, V. A. Ettel

A new solvent extraction process for the separation of cobalt, copper and zinc from nickel sulphate process streams has been developed. It involves selective extraction of these elements with a quaternary ammonium thiocyanate dissolved in an aromatic diluent. The chemical principles of this process have been investigated and are described, together with background physico-chemical data relating to the use of this solvent. Long-term testing in a continuous "mini-plant" circuit gave high-purity nickel and cobalt products (Ni/Co —200011 and Co/Ni ~1000/1 respectively).

Jan 1, 1976

By D. B. Dreisinger, D. G. Dixon, G. Nazari

"The kinetics of chalcopyrite leaching in acidic ferric/ferrous sulfate media under atmospheric conditions in the presence of pyrite has been investigated. It has been found that pyrite samples from different sources affect the rate of chalcopyrite leaching differently. A strong correlation between the amount of silver associated with the pyrite and its effectiveness has been noted. In this study, improvement of the catalytic properties of pyrite such that all pyrite samples accelerate the rate of copper extraction regardless of their sources is demonstrated, and a detailed discussion of the mechanisms involved in the process of chalcopyrite leaching in the presence of silverenhanced pyrite is presented. INTRODUCTIONIt is well known that chalcopyrite resists leaching in sulfate media. It has been proved that pyrite facilitates the leaching of chalcopyrite (Berry et al., 1978; Dixon et al., 2008; Mehta and Murr, 1983; Muñoz et al., 2008; Nowak et al., 1984, Tshilombo, 2004). Considering the catalytic effects of pyrite on accelerating the kinetics of chalcopyrite leaching, Dixon and Tshilombo (2005) have developed a new process, known as Galvanox™, which has several advantages over other hydrometallurgical processes. Galvanox™ runs under atmospheric conditions, so it requires only low-cost leaching tanks. The sulfur yield at this temperature is high (>95%) which leads to low oxygen consumption and low sulfuric acid generation. The operating temperature is below the melting point of sulfur which eliminates the use of surfactants. This process also does not require fine grinding. Reaction 1 shows the overall leaching reaction in the Galvanox™ process.CuFeS2 + O2 + 2 H2SO4 = CuSO4 + FeSO4 + 2 S0 + 2 H2O (1)Complete copper recovery from the Galvanox™ process can be achieved at a considerably higher rate than other atmospheric ferric sulfate leaching processes (Dixon et al., 2008). Recycling pyrite and recovering copper from tailings with the Galvanox™ process have also been evaluated in continuous pilot leaching campaigns (Dixon et al., 2007)."

Jan 1, 2012

By J. De Geoffroy, T. K. Wignall

The paper describes a statistical method based on regression and classification analysis which is designed to assist exploration management in the selection of prospecting areas and drilling targets in regional programs. The classification is based on three criteria which are formulated from sets of relevant geological, geophysical and geochemical factors: (a) regression estimates of expected ore values, (b) Bayesian probabilities of success and (c) expected utility payoffs. The advantages of the method are: (a) rational and unbiased ratings for areas or targets in a manner consistent with management's goals; (b) calculation of probabilities of success and confidence intervals for the ratings, and (c) rapid and accurate handling of a large amount of data by computer programs.

Jan 1, 1970

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By R. J. Enkin

Modern mineral exploration depends on multidisciplinary 3-dimensional integration of geological and geophysical data. Identification of the geological sources of geophysical anomalies requires knowledge of the physical properties fingerprint of rock types, formations and their alteration products. Understanding how and why rock physical properties vary within the Earth's subsurface ensures that appropriate geophysical exploration methods can be chosen, and allows for more efficient and effective surveys to be designed. Physical properties knowledge is integral to geophysical modeling - measured data or values estimated based on geological understanding are used to produce realistic forward calculations and to constrain inversion models. Mira Geoscience and the Geological Survey of Canada, in collaboration with industry and academia, are building a Rock Properties Database System (rpds.mirageoscience.com). It compiles the most valuable physical properties for mineral exploration (density, porosity, magnetic susceptibility and remanence, electrical resistivity and chargeability) linked with location and lithological metadata. A critical knowledge gap, addressed in this study, concerns the dependence of physical properties on alteration and mineralization processes. We report on the results of a collaborative University of British Columbia - Geoscience British Columbia project, ?Integrated Geological & Geophysical Porphyry Models: Adding Value to Geoscience BC Geophysical Data?. As part of the QUEST and QUEST-West geophysical initiatives, Geoscience BC focused detailed geophysical surveys on a suite of six known porphyry deposits: Mount Milligan, Endako, Huckleberry, Bell, Granisle, and Morrison. Physical properties for a set of 269 samples of characteristic host rocks and their altered equivalents were measured. The causes of physical properties variations were investigated through their correlations with ore and alteration mineralogy determined from thin-section observations and X-ray diffraction analyses. Physical properties of variably altered host-rocks and intrusive rocks vary significantly between different BC porphyry deposits. No specific unifying geophysical model exists that can be uniformly applied during exploration. Knowledge of local background geology and local physical properties variations is necessary as host-rocks and intrusive rock compositions vary depending on magmatic affinities, and alteration styles will vary reflecting host-rock compositions, crustal depth and influence of meteoric water. A district-scale exploration strategy requires location of intrusive bodies, which are commonly magnetic, resistive and low in density. Correlations should not be expected between density and magnetic susceptibility, because alteration may lead to magnetite destruction or to secondary magnetite development. Deposit-scale ground geophysics might image potassic alteration zones that can be magnetic in both alkalic and calcalkalic systems. Low magnetic susceptibilities, resistivities and densities might aid in locating the typically more porous phyllic and argillic zones. All geophysical data must be interpreted with background knowledge of local rock types and in light of the expected deposit model and associated magmatic and hydrothermal processes. The most effective means to building physical properties knowledge prior to geophysical investigation remains collecting rock physical properties measurements. The cost of rock properties data collection is low, relative to the overall costs of running a mineral exploration program, and can provide an important framework for design of geophysical surveys, survey method selection, geophysical modelling, and data interpretation.

Aug 1, 2013

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015