Search Documents

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By G. A. Gross

"Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained from iron-formation; another 20 per cent was formed by natural enrichment processes.Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical com-position and environment of deposition are of special significance in their evaluation as ore.The properties of the ores, including grade, beneficiation qualities and minor element content in taconites, metataconites and naturally enriched ores, reflect characteristics of the primary stratigraphie units from which they are derived. A detailed description of the stratigraphie facies is essential for efficient utilization of these source beds."

Jan 1, 1966

By K. Hawboldt, J. E. Halfyard, C. Bottaro, I. A. Harrison

"The removal of elemental sulfur from leach residues derived from massive sulfide concentrates via hydrometallurgical routes has been demonstrated in a laboratory setting by converting water-insoluble sulfur to water-soluble polysulfides. The approach was applied to leach residue from Vale's nickel hydromet demonstration plant in Argentia, Newfoundland, which contained significant amounts of elemental sulfur. This technique offers an alternative treatment protocol for residues with a sulfur component not amenable to standard flotation/hot filtration processes. The practical considerations of a proposed flow sheet will be discussed including the impact of other sulfur species (e.g. thiosulfate and sulfides) and key process variables. INTRODUCTIONPresently, large scale elemental sulfur extraction from hydrometallurgical leach residue is performed by Teck Resources using a process of sulfur flotation followed by hot filtration (Chalkley et al., 1993). As mentioned, the technique proves viable for residues derived from specific concentrations - in this case zinc - whose residues constituency is primarily elemental sulfur itself. However, problems arise when this constituency is altered as happens when, for example, a mine containing one particular concentrate is mixed or replaced with a differing concentrate from a second mine. Such cases can often strain the effectiveness of current sulfur removal processes (D'Odorico, 2004). If hydrometallurgical residue containing elemental sulfur cannot be effectively treatment by flotation, the residue is stored subaqueously as is the case in some 'grass roots' hydrometallurgical plants (those not coupled with smelting operations). Hydrometallurgical processing of concentrates involving pressure leaching is becoming increasingly common throughout the mining world, the genesis of which can be found in research performed by Sherritt in Fort Saskatchewan since the 1950’s (Ozberk et al., 1995).The investigation of elemental sulfur removal by means other than flotation includes the uses of sulfide salts (NH3S or Na2S) effecting the conversion of hydrophobic elemental sulfur to hydrophilic polysulfides. The work of Kunda et al. (1974) and Olper et al. (2007) shows that elemental sulfur can be quantitatively removed from hydrometallurgical leach residue via the formation of a mixture of polysulfides."

Jan 1, 2012

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By Eldon L. Brown

Location and History The Sherritt Gordon property is located in northwestern Manitoba, about 100 miles north of The Pas and 40 miles northeast of Flin Flon. It is connected with the Manitoba Northern railway, which runs from The Pas to Flin Flon by a branch line, 42 miles in length. The location of the property is shown on the sketch-map, Figure 2. The ore deposit was first discovered by Philip Sherlett, a Cree Indian, in 1922. In 1924 Sherlett's claims lapsed and the ground was re-staked by Carl Sherritt and Dick Madole, and was optioned by them to J. P. Gordon in the summer of 1925. Gordon re-optioned the property successively to three well-known mining groups, one of which did some surface trenching .and put down 28 shallow diamond-drill holes before dropping their option. In the latter part of 1927, a Company known as Sherritt Gordon Mines, Limited, was formed to take over the property, and preparations were made for systematic development work. Preliminary Development In order to fill-in gaps left by the original drilling, a light diamond-drill outfit was flown-in to the property from the Hudson Bay railway in the early fall of 1927. Ten shallow holes were put down before freeze-up .and a considerable amount of surface trenching was completed. Based on the results of the surface trenching and the shallow diamond-drilling, an extensive development campaign was outlined. A winter road, 90 miles in length, was cut from mileage 55 on the Hudson Bay railway, and during the winter of 1927-28 a total of 2,600 tons of freight was hauled-in to the property. This freight included four complete diamond-drill outfits, two complete mining plants, building material for two sets of camps, and supplies for one year's operations, including 105,000 gallons of fuel-oil for Diesel engines.

Jan 1, 1933

During the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits. However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses haw not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently am poorly doc-umented, the use of these terms is reviewed. Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco's Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delin¬eation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study. The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit by 39.27% and 45.41%, respectively, and that of the 6 m wide deposit by 12.84% and 11.55%. As the impacts of ore loss and those of dilution on the net present value am almost identical in these simulations, we could, in practice, assume a 50/50 split between dilution and ore losses in such a case. These results do no take into account the effects of local optimization measures taken at the mine production level (blasthole sampling near stope limits, etc.) The potential impacts of geological and sampling uncertainties in terms of lower NPV justify and require more systematic efforts to ensure that deposit appraisal work and feasibility studies are adequate to optimize company revenue and competitive returns to investors from mine production activities.

Jan 1, 2005

By J. M. B. Scarborough

This paper deals with measures taken to maintain effective operation of heavy-duty equipment in open-pit mining. at Pine Point, N.W.T., during periods of extreme cold weather. The points covered include equipment modifications designed to improve cold-weather performance, effective lubrication of machinery that is vulnerable to extreme cold and operating procedures designed to prevent equipment damage.

Jan 1, 1966

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By T. M. Korzekwa, R. L. Cavanagh

Following considerable experience with the beneficiation of Wabana iron ore by standard methods, a study was made of the benefits to be obtained by semi-reduction. The basis of the laboratory program was an extensive mineralogical and liberation investigation which guided subsequent work. Partial reduction and beneficiation on a laboratory scale was carried out on lump ore and fines. The reduced ore was magnetically concentrated and the concentrated fines were briquetted. Data are presented on reducibility, sizing vs reduction rate, magnetic cobbing and separation, and the elimination of phosphorus. Past work is reviewed briefly and comments are made on the relation of laboratory to pilot-scale tests.

Jan 1, 1967

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By Lifeng Yang, Xiang Zhang, Liang Yuan, Yonghui Wang, Bing Hou, Mian Chen, Rixing Zhang

Large-scale hydraulic fracturing technique has been widely applied to the development of shale gas reservoirs, where the interaction between natural fractures and critical fracture zones has substantial impact on the propagation of hydraulic fractures. Therefore, it is of significant importance to understand and experimentally verify such mechanism. To reach this end, tri-axial fracturing tests were implemented on 400mm×400mm×400mm block samples collected from Longmaxi shale outcrops. The interplay between hydraulic and natural fractures was investigated during the tests, factoring in the role of pump rate in affecting the created fracture network. Based on the experimental results, the critical fracture zone, defined as the weak formation zone nearby the wellbore created by staged pressure implementation that is observed rapid fracture propagation upon next stage of pressure increase, was thoroughly investigated. The analysis illustrates that given the high brittleness of the shale formation, abundant critical fracture zones are generated around natural fractures with pressure building up at a relatively low pump rate. As the pump rate increases, hydraulic fractures initiate and come into play with critical fracture zones, implying emergence of a large number of micro-cracks. A changing pump rate modifies the way of interaction between hydraulic and natural fractures and the subsequent formation of fracture network. Long term fracturing fluid injection with relatively low pump rate below the activation of critical zones is suggested. Also proposed is appropriate timing when applying a specific pump rate that will contribute to the improvement of hydraulic fracture propagation.

Jan 1, 2015

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine&apos;s main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco&apos;s lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By J. W. Craig

THERE are, broadly speaking, three classes of refractories: acid, basic, and neutral. Fireclay, diaspore, silica, and the sillimanite group of minerals are included in the acid class, which for the most part are not very resistant to basic slags. The neutra! class includes chrome, graphite, and silicon carbide, while most important in the basic class are magnesite and dolomite. Although chrome is a neutral refractory, it has no sharp distinction from magnesitic refractoriness. The two are mineralogically (1) and chemically related, and there is available on the market a complete range of brick from straight chrome to straight magnesite. In many indus trial applications, one. type may be replaced by another. The present paper is confined entirely to such refractories. The following types of basic and neutra! brick, each sold under sorne special trade name, are available for use in Canada: (1) Burned chrome from crude ores (2) Burned chrome from treated ores (3) Chemically bonded (unburned) chrome-magnesite ( 4) Burned chrome-magnesite (5) Chemically bonded ( unburned) magnesite-chrome (6) Chemically bonded (unburned) high-iron magnesite (7) Burned high-iron magnesite (Regular) (8) Burned low-iron magnesite (9) Burned olivine-magnesite (10) Burned magnesitic dolomite-chrome (Magnecon) (11) Chemically bonded magnesitic dolomite-chrome (Magmecom) (12) Dolomitic brick

Jan 1, 1936