Search Documents

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By J. T. Fyles, C. G. Hewlett

"THE TOWN OF Salmo, rail centre for the Salmo lead-zinc mining district, is in southeastern British Columbia 26 miles by road east of Trail an about the same distance south of Nelson. The belt in which the mines occur is a few miles east of Salmo and extends about 6 miles north of the town and 17 miles south and southwest to the International Boundary. The belt includes the H. B. mine of The Consolidated Mining and Smelting Company of Canada, Limited, the Jersey mine of Canadian Exploration Limited, the Reeves MacDonald mine, and the Jack Pot property of New Jersey Zinc Explorations Limited.Since 1949, the Jersey and Reeves MacDonald mines have produced most of the lead and zinc in the district. From 1949 through 1954 these two mines together produced a total of 233,134 ounces of silver, 87,659,399 pounds of lead, 215,708,856 pounds of zinc and 475,397 pounds of cadmium. This amounts to more than 80 per cent of the total production of lead and 95 per cent of the total production of zinc from the district since the first recorded production in 1906. Reserves at the largest properties amount to several million tons of ore containing 4 to 7 per cent combined lead and zinc. Several prospects are potential producers.Regional StructureThe main structural units in the Salmo area are outlined in Figure I, and the major rock units of the stratigraphic column are listed in the following table. The lead and zinc deposits are replacements in a highly deformed limestone formation near the base of the Laib group, and all mineralized zones are on the south and east side of structural unit 2 (see Figure I)."

Jan 1, 1949

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

By Wm Petruk

"The tungsten-bismuth-molybdenum deposit in southwestern New Brunswick occurs in greisenized and silicified tuffite * and feldspar porphyry in and adjacent to volcanic necks. The ore minerals occur as veins and veinlets and as disseminated grains in gangue. These minerals can be grouped into three assemblages. Assemblage 1 consists of oxides and phosphates of W, Ti, Fe, Nb, Sn, Ta and rare-earth elements, with the main minerals being deposited in the sequence wolframite, rutile, cassiterite. Assemblage 2 consists of arsenopyrite, molybdenite and bismuth, and assemblage 3 of sulphides with minor cassiterite and arsenopyrite. Sphalerite is the main sulphide mineral, but it contains minute inclusions of copper-tin- and indium-bearing minerals. Textural relations suggest that most of the elements can be recovered from this ore by conventional mineral beneficiation and extraction methods, but a variety of techniques must be employed. It is expected that the wolframite and molybdenite can be recovered satisfactorily, but poor recoveries are expected for bismuth and cassiterite. A sphalerite concentrate can be readily obtained by flotation, but it would contain a wide variety of elements. It is suggested that leaching be used to recover the bismuth and the elements in the sphalerite concentrate."

Jan 1, 1973

By A. C. Ross

"The paper will deal with non-destructive testing in general, and its advantages to those responsible for the maintenance of wire rope. An outline of the main features of the M.D. 6 Defectograph will be given, and the method of operation and results obtained will be described.The instrument will accommodate ropes at 7 /16-to 2 %-inch diameter at reasonable speeds, and is capable of detecting the most minute defects in even the largest-diameter wire ropes."

Jan 1, 1969

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By Ben Habermann

"The object of the work described in this paper was to increase the understanding of the relation that capillary pressure of a rock, hydro-dynamics, and accumulation of oil in stratigraphie traps have to one an-other. The hydrodynamic oil-water tilt equation is derived by considering the two vector gradients involved: (1) buoyancy of oil in water and (2) hydraulic gradient.Recent theories show the necessity for oil to have a continuons phase in the reservoir rock in order to mi-grate; this fact applies to hydro-static as well as to hydrodynamic conditions. Hydrostatically, the displacement pressure of the rock deter-mines the amount of oil that can be trapped behind a permeability barrier. If the buoyancy of oil in water exceeds the displacement pressure, oil will migrate up-dip; an oil trap will be formed where displacement pressure is greater.In stratigraphie traps the pressure drop caused by moving water is positive when its direction is down-dip, helping accumulation; and it is negative when its direction is up-dip, forcing the oil into the tighter section of the reservoir. Theoretically, pro-vided we have data such as: (1) the displacement pressure of an up-dip permeability pinchout, (2) density difference between the oil and water in place, and (3) the direction and magnitude of the hydrodynamic gradient (if any), the possible extent of a stratigraphie oil accumulation down-dip can be predicted.To test the above theory sample cores from three wells in the Denver Basin were analyzed and the oil column that could be held under hydro-static conditions was calculated. After the hydrodynamic influence was considered, the results were compared with actual field data.The significant fact shown by this investigation is that the calculated oil column in one reservoir very closely approximates the actual extent of the oil column in a well. Also in accordance with the theory, the capillary pressure caused by the buoyancy of the oil column exceeded the measured displacement pressure on core samples from another productive field. For very tight shaly sand and questionable oil shows, the interpretation of data is very critical, as shown by experiments on core samples from a third field."

Jan 1, 1960

By Robert E. Wood

Engineers have known for some time that the efficiency of filtering iron ore concentrate slurry can be significantly improved by pre-heating the slurry ahead of the filters. However, heating such large quantities of dense slurry by conventional means has proven to be inefficient and high-maintenance. Recently though, submerged combustion was considered by Altos Hornos de Mexico SA (AHMSA), an integrated steel producer in the state of Coahuila, Mexico, as a means of pre-heating their iron ore concentrate. The company toured many iron ore facilities in Brasil and Labrador, reviewing their heating processes, and concluded that submerged combustion could provide a competitive advantage through operational efficiency and lower capital cost than steam boilers. Inproheat was retained by the company to design and manufacture a SubCom slurry heating system to heat 403 m3/h of iron ore concentrate slurry from 25°C to 60°C. The 60GJ/h SubCom system consists of five natural gas combustion chambers mounted in an iron ore concentrate storage tank. The system features a heat recovery unit whereby the exhaust gases are used to preheat the incoming slurry stream, giving the system an overall thermal efficiency of 95%. As a result, the steel company expects to realise significant improvements in filtering efficiency which will enable them to increase the capacity of their pelletising plant without installing additional filters.

May 1, 2010

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

It was determined by the authors that the water that remains in the filter cake after filtration in iron ore concentrators can contain several hundred times greater concentrations of calcium ions and other cations, due to surface chemical effects carrying the ions along with the water. Filter cake from two plants was analyzed. The water retained in samples of magnetite concentrate filter cake in Plant 1 contained 5088 ppm calcium and 5995 ppm magnesium, while the Plant 2 filter cake contained 231 ppm calcium and 119 ppm magnesium. These levels were dramatically elevated compared to the water that was removed from the concentrate by filtration for recycle to the plants (9 ppm calcium/15 ppm magnesium for Plant 1, and 11.9 ppm calcium/9.3 ppm magnesium in Plant 2). In addition to possible effects on agglomeration performance, the presence of these cations also affected the efficiency of filtration. In order to reduce the effects of these cations on filtration in Plant 2, carbon dioxide was injected into the slurry before it entered the filter press. This was found to increase filtration rates by up to 23.7%. Comparison of the results from the two plants shows that the concentrations of cations present in the filter cake will vary greatly from plant to plant, with correspondingly large variations in their effects on plant operations.

Jan 1, 2004

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By Franz Xaver Spachtholz

K+S Potash Canada GP (KSPC) is part of the K+S Group, one of the world's leading suppliers of standard and speciality fertilizers and the world?s leading salt producer. Globally, the K+S Group employs more than 14,000 people. The K+S share ? the only commodities stock on the German DAX index ? is listed on all German stock exchanges. Legacy, K+S Group?s most recent project, is a greenfield solution potash mine and production plant in the south of the Canadian province of Saskatchewan. Therefore K+S will invest 4.1 billion CAD. With the expected commissioning in summer 2016 the company projects to reach the two-million-tonnesmark of production capacity at the new location at the end of 2017. The gradual extension of the annual capacity to 2.86 million tonnes of potash products will occur afterwards. The Legacy Project will be Saskatchewan?s first new potash mine in nearly 40 years. It is one of the world?s most economically attractive potash projects. The project will contribute to Saskatchewan?s growth through employment, tax revenues, utilities, and local partnerships. Located in the southern part of Saskatchewan?s potash belt, the deposit is too deep to be mined conventionally due to rock mechanics and high temperatures. Legacy will therefore be a solution mine. Proximity to the urban centers of Regina and Moose Jaw is imperative, with their workforces and economy, as well as access to highways, railway carriers and, most importantly in the prairies, water. With this unique project setting and mining technique, we are convinced that Legacy will be one of the most efficient, economic, sustainable and safe potash facilities in the world.

Aug 1, 2013

By E. R. Weltevreden, C. Klauber, C. Vernon

"In this paper a review of the current status in recycling technologies for cathode ray tubes is given for both the glass and phosphors. Particular emphasis is placed on the opportunities for the recovery of the rare earth elements (REE) from the phosphor coatings. This is placed in the market context of alternative virgin sources and some of the advantages and disadvantages for REE waste recovery. Future opportunities are explored and also some experimental detail on a low cost leach system is presented. INTRODUCTIONThe disposal of cathode ray tube (CRT) based colour televisions has accelerated world-wide with the development of high definition flat screen panels. The total number of colour CRT televisions that have been sold in the United States in the mid-20th century is estimated to have been over 2 billion (U.S. Environmental Protection Agency, 2007), with high current rates of disposal. It is estimated that of the 20 million televisions annually discarded, 78% are send to landfill (Nnorom, Osibanjo & Ogwuegbu, 2011). However, this easily accessible item of electronics cannot only be turned into a valuable resource using the right recovery procedures, it can also prevent the substantial environmental contamination arising from improper disposal. In this review we focus on previous and current work performed on the recycling of CRT based televisions. Due to the increasing demand for rare earth metals, the main focus will be on the possibilities and challenges of recycling the fluorescent phosphor powders on the CRT’s panel glass.CATHODE RAY TUBE’S GLASS RECYCLINGConventional cathode ray tubes consist of three main parts, the panel, the funnel and the neck (Figure 1). To produce the different colours on the screen, the inside of the panel is coated with a matrix of hundreds of thousands of small phosphor dots. Each dot is one of three types of coloured phosphors, emitting either red, green or blue light. These emit light when excited by a beam of electrons generated by electron guns located in the neck of the CRT. These beams pass through holes in the shadow mask and excite the phosphor coating on the inside of the panel, to give light of variable RGB composition, see Figure 1."

Jan 1, 2012

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977