Search Documents

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electrolyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions.The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was investigated as a method of optimising glue additions in the presence of antimony.Scanning electron rnicroscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltarnmetry measurements showed some correlation between current efficiency and activation polarisation potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1988

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

Platinum Group metals have been known in New Zealand since the 1880's but not produced on a large scale. They have been neglected because their value was not appreciated rela- tive to gold and their value was often very low, reflecting demand, and because recovery was difficult compared with recovery of gold. With the rising price of most Platinum Group metals and the perfection of gravity and flota- tion recovery methods, recovery of platinum along with gold from alluvial deposits is more attractive. Platinum Group metals are known in several different environments in New Zealand, ranging from alluvial placer deposits to layered basic to ultrabasic intrusions and quartz veins. None of the known occurrences have been ade- quately prospected and there is a real possibi- lity of future discovery of important deposits. Several New Zealand based and at least two offshore resource companies are currently involved in exploration, prospecting or mining for Platinum Group metals in New Zealand.

Jan 1, 1987

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

Information from bores in the LatTobe Valley has been accumulating for over fifty years, and the manual extraction of details has become a limiting factor in their use.Punched card equipment, installed by the State Electricity Commission for accounting purposes, was known to be available for reasonable periods, and it was suggested that this could help in the extraction of data from the voluminous records.Investigation showed that they could be substantially duplicated on cards, with consequent gains on many operations; the cards being regarded as an auxiliary to the existing records.BRIEF DESCRIPTION OF RECORDSAs a bore is drilled a continuous record of the strata is kept, together with notes on the presence of water or any unusual features which the driller may observe.When coal is struck, samples of each ten feet are usually sent for analysis.The location and surface level of each bore is fixed by surveyors, and details of dates and methods of drilling are also kept.Bores are allocated numbers, prefixed by the name of the parish within which they are drilled. Numbers are allocated in conjunction with the Department of Mines, to avoid duplication.Records of strata and analyses are kept in folders, with 100 bore numbers per folder.Standard plans are drawn, showing the locations, bore numbers and surface levels. For each bore they also show the depth and thickness of coal struck, and the total depth drilled.Cross sections are then drawn, connecting the various coal seams, which have been identified by the geologist.

Jan 1, 1960

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

By M Roberts

The aim of this paper is to evaluate the technical feasibility of application of the electric monorail as a haulage system in hard-rock underground mining in Australia, in comparison to conventional truck haulage systems. The elements of the system being investigated include mine design and layout, installation, loading and unloading subsystems, tramming speeds, cost and productivity, automation, ground support, safety and environmental factors. Electric monorail systems are potentially more cost-effective due to a range of factors: only the one system may be needed for the transportation of workers, material and rock; and excavations for monorail haulage can be smaller and mined at much steeper gradients than for truck haulage. The smaller excavation size also reduces the need for costly ground support and û in another important measure for the health and safety of mine workers, and for energy savings û it reduces ventilation requirements. Electric monorail haulage technology is being applied in hard rock mines in South Africa and considerable benefits have been realised by the industry in that country. In Australia, mine designs for metal mines generally remain based on truck haulage and/or shaft hoisting systems. There is a tendency to apply these haulage systems to every orebody. For the industry to achieve sustained growth against a backdrop of volatile diesel prices and environmental concerns, new generation underground haulage systems are required. The monorail haulage system offers opportunities in improving materials handling efficiencies in underground mining operations. This paper examines the application of monorail haulage in metalliferous underground mining, presents comparative data with track and trackless haulage systems and develops concepts for system application in combination with conveyor belt haulage and narrow vein mining situations.

Jan 1, 2005

In presenting size analysis data, one has the choice of various graphical techniques; each no doubt has been developed to highlight a particular aspect of the data. A frequency size distribution plot is used quite extensively to illustrate the importance of the finer size particles in iron ore granulation. However, the basis for such a plot is often not appreciated. As a result, cases of incorrect use can be cited. The aim of this paper is to extend the work of Alien (1981) and to provide, using examples and figures, a basic understanding of the implications of the various size distributions. A simplified method of presenting sizing data on a linear scale graph paper is presented and recommended. This involves a simple construction of a histogram of mass fraction versus particle size (in geometric progression).

Jan 1, 1992

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

Projections of metal requirements for Japan and the United States indicate growing competit- ion for Australia's mineral output and a critical need for continuing discovery of new reserves. These projections may be modified by economic, social and political controls - the most import- ant factor probably being a shortage and the high cost of risk and development capital. Changing ownership patterns toward joint ventures and increased state participation are anticipated. New developments in global tectonics and metallogeny delineate favourable zones for ex- ploration and permit establishment of priority search areas even in regions of poorly known geology. Declining ore grades and special character- istics to meet technological requirements may modify identification and evaluation criteria. A broad approach considering all environments of concentration within the geochemical cycle is re- quired within any metallogenic province. The exploration geologist must be able to integrate geological theory, mining technology and financial analysis to establish well defined exploration objectives, in terms of economic and geologic models, in concept-oriented programmes.

Jan 1, 1973

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

THIS paper is not intended to be more than a mere outline of the economic geology of Tasmania. It is desired to present in a condensed form the present state of our knowledge in regard to the distribution of the ore, coal, and oil-shale deposits of Tasmania in time and space.Tasmania is exceptionally well endowed with mineral wealth, particularly in the north-western and western districts. In the enthusiasm resulting from the first discoveries of mineral deposits at a great number of localities in those districts, it became a generally accepted belief that the whole of that portion of Tasmania constituted a continuous metalliferous province. As geological research in these, areas has progressed, however, it has become increasingly clear that ore-deposition has been confined on an economic scale to definite well-defined areas or belts which have a genetic relationship to certain tectonic and petrologic phases of the general geology. These areas or belts have recently been defined by the writer, and...

Jan 1, 1923

By Liu Z. C

Evans' theory for chisel shaped picks is well known in the field of rock cutting technology. It has been widely accepted as a good mathematical description of how coal and other rocks break under the action of a simple wedge or chisel. Subsequently, Evans proposed a corresponding theory for pointed shaped picks. Theory along with experimental evidence from the laboratory has consistently shown that chisel picks are more efficient than pointed picks. However despite such evidence, pointed picks continue to be the preferred shape in most practical cutting applications. Evans' theory for pointed picks was developed in an attempt to shed light on this apparent incongruity. The theory although predicting forces of the right order was found to be deficient in several respects. This paper examines Evans' theory for pointed picks and proposes changes to it, which brings the theory much more into line with measured data. The issue of the relative efficiencies of chisel and pointed shaped picks is also examined on a theoretical basis and the apparent incongruity is Resolved.

Jan 1, 1995

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

By Miovski P, Hooft P. V

In the majority of recently commissioned gold mines granular activated carbon is used to adsorb gold from alkaline cyanide pulps or solutions. At the same time the carbon also adsorbs many other inorganic and organic species, most of which lower the activity of the carbon. Removal of these foulants is necessary before the carbon is reactivated and recycled. Standard practice for re- storing carbon activity involves high temperature treatment in a kiln - an apparently straightforward unit operation which is not always satisfactorily carried out. This paper presents the results of some fundamental work carried out on the thermal reactivation of carbon in a laboratory rotating pot kiln. The effects of temperature and steam addition on carbon activity were examined and compared with the activity of carbons obtained from a number of commercial kilns. Carbon was also reactivated using a small-scale Rintoul Furnace in which carbon was resistively heated by the direct passage of an alternating electric current. It was established that both elevated temperatures and the addition of steam to hot carbon generally enhanced its activity although peat-based extruded carbons responded a little differently to coconut shell types. Other measurements made included the weight loss and the hardness of carbons as a function of reactivation conditions.

Jan 1, 1987

There are countless petroleum and mineral fiscal systems throughout the world. This is because many petroleum and mineral producing countries have developed their own methods of calculating government take through fiscal evolution or individual negotiation. Those countries fortunate enough to have petroleum and mineral reserves within their national boundaries are naturally reluctant to yield this resource without a reasonable return for their population. As resource companies are perceived to be enormous conglomerates with endless amounts of cash and resources, governments and the general public demand reasonable division of production while these finite resources last. On the other hand, because companies engaged in the exploration for, and production of, minerals, oil and gas have to be large or lucky (preferably both) to sustain the great physical and commercial risks involved, the income and profit figures look so large that the general public sees them as an acceptable target for taxation. Taxation of the resource industry has been one of the industry's greatest cash flow problems through the years. Allen and Seba (1993) attribute this to the fact that the most equitable tax systems are those that affect the widest possible total of the population.

Jan 1, 1996

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

By Paine GG

In coal mining each of the unit operations are interrelated with each preceding operation having an effect on subsequent operations. This presents difficulties for determining when the lowest overall costs for a particular mining system are achieved. Drilling and blasting is the first mining operation for production and is known to have an effect on the subsequent loading, hauling and crushing operations. Computer blasting models developed over the past 15 years can be used to describe the drilling and blasting operation. This paper describes the ICI Blasting Model "SABREX" in detail. Methods of using the model are discussed. This involves field measurements of geological structure, shallow refraction seismic surveys, laboratory measurements of rock properties and high speed photography of blasts. The predictions are compared with actual blast results for fragmentation sizing and muckpile profiles. Outputs from the model are described and these can be used for input to models of subsequent operations.

Jan 1, 1987

Virtual reality (VR) simulators represent a powerful tool for training humans to perform tasks which are otherwise expensive or dangerous to duplicate in the real world. The idea is not new. Flight simulators have been used for decades to train pilots for both commercial and military aviation. These systems have advanced to a point that they are integral to both the design and the operation of modern aircraft (Adams, Klowden and Hannaford, 2001; Mastaglio and Callahan, 1995). This technology has been successfully extended and utilised in the mining industry in a range of successful applications (Bise, 1997; Denby and Schofield, 1999a; Schofield, 2005; Henning et al, 2002; Kaiser, Vasak and Suorineni, 2005). There are a number of lessons that can be learned from other industries that have successfully utilised virtual technology for a number of years. Specific rules of thumb regarding the specification, development, application and operation of these simulators can be garnered from other industrial training systems and examined in a minerals industry context (Tromp and Schofield, 2004; Schofield, 2006). This paper intends to discuss some of these generic rules in the context of a number of recently developed virtual reality mining applications.

Jan 1, 2008

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar'e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958