Search Documents

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

By Kavetsky A

A new model of flotation is presented which allows predictive calculations of total solids flows and metal grades and recoveries to be made for industrial flowsheets. A method of making these calculations is presented and illustrated with examples. The problem of determining sufficient flotability characteristics from a sample of circuit feed to predict the behaviour of that specific ground ore in the flotation circuit (ie performing flotometric analysis) is addressed, and some suggestions are made for its solution. A feature of the flotation model is its practical technological orientation, allowing determination of a small number of ore flotability parameters by fitting observed batch kinetic flotation data. The unit model explicitly includes the cell aeration as total bubble area per unit pulp volume, and pulp residence time. Although more complex unit models are feasible, it is thought that this model is sufficiently realistic to illustrate the points made. The modelling approach is illustrated by application to flotation data from a Kambalda ickel circuit. The model is parameterised and ore flotability parameters are back-calculated from batch kinetic data. These parameters are then used to fit the observed behaviour of the industrial circuit by numerically adjusting the unit aerations. Finally, it is shown how the model may be used to predict the effect of circuit and ore changes on the circuit's technological indices.

Jan 1, 1992

By P A. Dowd

This paper describes an integrated approach to the evaluation of ore loss and ore dilution via geostatistical simulation of in situ geology and grade characteristics, simulation of blasting mechanisms and simulation of loading from a blast muck pile. The approach is demonstrated on a case study. The sequential Gaussian method is used to simulate in situ bench grades on the scale of the smallest selectable volume within a blast muck pile. The simulated grades of these component volumes are interpreted as the reality that would be available with exhaustive sampling. The simulated bench is subjected to a blast simulator, based on the SCRAMBLE model, which effectively moves each of the component model volumes to its final resting place in the blast muck pile. Ore/waste delineation and selective loading processes are applied to the simulated muck pile to determine the degree of selectivity that can be achieved by various sizes of loader and types of loading and to quantify ore dilution and ore loss. An in situ model representing the reality of knowing only the data and information that are available from specific grade control drilling and sampling grids is obtained by sampling the geostatistically simulated model on a specified grid. The volumes comprising the in situ model are then populated by estimates based only on the data and from the specified grade control drilling and sampling grids. Different drilling and sampling grids are used to generate different models, each reflecting the levels of data and information available. Selectivity is assessed as a function of the drilling and sampling grids as well as the size and type of loader. Performance is assessed against the ideal selectivity that could be achieved on the perfect knowledge model comprising the simulated values of each component volume. Costs, prices and financial criteria enable an optimal selection of the grade control drilling grid, size of loader, type of loading and blast design.

Jan 1, 2004

By Baafi E. Y

In this paper, impact of expert systems development is examined from the coal mining point of view. Some introductory concepts about expert systems are explained with a view to identifying possible beneficial applications of expert systems in coal Mining.

Jan 1, 1988

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By Sillet R, Corin P. J, Wilson G

Zinc Corporation of Broken Hi11 had some long hole stopes coming into use which could not be mined using diesel loaders, because of ventilation restrictions. In preference to use of pneumatic loaders, and because there were no field proven electric loaders in Australia, Horwood Bagshaw Ltd., were commissioned to repower a diesel loader with an electric motor, within the confines of the existing machine

Jan 1, 1977

By Harraway DH, Tanner AC

The various circuits tried!at Mount.Isa Mines during the period 1959-1963 to improve the differential%f lotation of galena and sphalerite are reported. The benefits and disadvantages of 'the various circuits are discussed. An analysis of ore charao-beris;ics.and their effect on flotation is followed by the d~soription,of a proposed".cirouit in the process of install-ation.

Jan 1, 1963

By Davies C. E

At present the source of virgin iron for steel produced in New Zealand is titanomagne- tite extracted from titaniferous beachsands. Some of these beachsand deposits contain extractable quantities of ilmenite as well as titanomagnetite and both minerals represent challenging sources of vanadium and titanium products in addition to iron. This study looks at some theoretical aspects of smelting these ores directly with coal rather than with electric power, and takes into consideration the properties of the raw materials, the thermodynamics of possible process routes and the background of the economics involved.

Jan 1, 1980

Mining and metallurgy are more capital intensive than all other industry in Australia. Capital demands are met by domestic and foreign sources of finance for whom the major constraints are the supply of funds and factors of risk and uncertainty. in both mineral development and institutional financing policies, specific options are available to administrators which would allow mining to benefit from a more reliable supply of capital. The strength of major partners involved and overseas participation are important aspects of financing mineral developments. Future changes in financing for the mineral industry are considered most likely in variable interest rate funding, in the leasing of major plant items, and in the development of flexible techniques to ease the burden of infrastructure costs. In a consultancy sense, financiers are available to mining to assist with and to advise on optimal develop- ment of mineral industry projects.

Jan 1, 1975

By N Patzelt, T C. Logan, I B. Klymowsky

In 2003, NEWMONT MINING CORPORATION, the worldÆs largest gold producer, set out to prove that High Pressure Grinding Roll (HPGR) technology is sufficiently robust and reliable to be considered for the treatment of hard rock gold ores. In collaboration with POLYSIUS, a significant trial was conducted and 127 600 tonnes processed, successfully proving the HPGR capabilities on the Lone Tree Mine, Nevada ore û one of the most competent and abrasive ores in the industry. The success has led a number of mining companies to consider HPGRs for the comminution of gold and copper ores.

Jan 1, 2004

By G H. Luttrell

The use of secondary desliming cyclones ahead of froth flotation cells to reject ultrafine (-45 ¦m) particles has become a popular option in the United States for preparing fine coal feeds for froth flotation circuits. In light of this popularity, several experimental studies have been performed at industrial plant sites to develop a better understanding of the impacts of ultrafine desliming on froth cell performance and, ultimately, overall plant performance. These studies included an evaluation of various circuit configurations incorporating different flotation technologies (conventional machines and column cells) as well as different dewatering systems (disc filters, screen-bowl centrifuges, and thermal dryers). The data obtained from these studies indicate that deslime circuits offer several important benefits including lower product ash, reduced product moisture, better froth handling characteristics, and lower capital and operating costs. In addition, case studies conducted as part of this investigation have been used to develop generic guidelines for how deslime circuits may be successfully applied to improve the overall profitability of fine coal flotation circuits for both the metallurgical and steam coal markets.

Jan 1, 2005

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

Although giant strides have been made in the Australian mineral industry over the past quarter of a century in terms of mineral discoveries, self-sufficiency of commodities, contributions to exports and other aspects, there are unhealthy signs emerging which require attention. For instance there are 20 out of 34 discoveries of base metals, uranium and nickel which for a number of reasons await development. Some of the reasons for the standstill in the mineral industry are partly economic, partly due to competing land use, uncertainty in applying or, recognising the principle of crown ownership of minerals, and to some extent lack of appreciation of two closely related exploration activities referred to as development exploration and assessment Exploration.

Jan 1, 1979

This paper discusses basic practices of operation applied to raise drilling. It draws attention to critical areas that tend to be neglected. A brief history covers development of raise drills. The elements of the equipment, derrick assembly, drill string and reamers are ex- amined. Particular emphasis is on the drill string. It is concluded that manufacturer and operator can benefit each other by closer interchange of ideas.

Jan 1, 1977

For decades strip mining with discon tinuously operating 'draglines and shovels has been the most economical operation method in the shallow hard coal opencast mines of Aust- ralia, North-America and some other countries. Continuously operating equipment such as bucket chain excavators and bucket wheel excavators in combination with conveyor belt systems, conveyor bridges and stackers had been deve- loped in Germany; during the last 25 years this type of equipment has been further developed in order to allow a high degree of rationaliza= tion as to opencast mines in unconsolidated overburden in Germany, in many European couh- tries, in India and in Victoria. The differing compactness of the layers to be mined, the increasing mining depth, the adverse over- burden to coal ratio and geotechnical con- ditions account for the combined use of con- tinuously and discontinuously operating equip- ment and systems. This paper is to demonstrate some projects showing the combination of continuously and discontinuously operating equipment which aims at optimizing opencast mine operations. It will be reported on the following combinations: - combined use of bucket wheel excavator/

Jan 1, 1981

By Morrison R. D, Davis J. J, Fraser B, Kojovic T

1991 saw the completion of a three-year $1.1 million research and development program in mineral sands beneficiation, funded in two associated projects by the Australian mineral sands industry through AMIRA, and carried out by the Julius Kruttschnitt Mineral Research Centre. It is believed to be the largest R&D project in mineral sands ever conducted by a university research group. It covered dry plant operation, and delivered several products to the industrial sponsors, including: ò A detailed characterisation of the radiation properties, mineralogy and size distribution of inhaleable dust arising in dry plants. ò New process models of magnetic and electrostatic separators. ò New on-line instruments for elemental assay (in association with AMDEL) and bulk conductivity measurements of dry process streams. ò Demonstration and evaluation of the Magstream magnetohydrostatic separation technology.

Jan 1, 1992

By Hammett PHJ

Oil Exploration Companies are primarily interested in how much oil or gas is present in the rocks in an area in which an exploratory well is drilled. The solution of this problem requires a combined effort on the part of the petroleum geologists, drilling engineers, logging and drilling contractors. To help in'explaining how the drilling and evaluation is earried out the paper has been divided into two sertions, one titled Drilling which is presented by Mr. P.H.J.-Hammett and the seeond titled Evaluation which is presented by Mr. R.M.L. Elliott. A typical Perth Basin Well has been chosen as art example for this presentation. In Figure 1A is shown the type of sandstone and shale sequence encountered in this area.

Jan 1, 1964

By R Lastra

Applied mineralogy involves conducting investigations on ores, minerals and materials to solve problems encountered in mining, metallurgy, processing, industrial minerals, environment, health and other fields. The investigations are performed to determine the mineral behaviours during processing by using every mineral and ore characterisation technique and appropriate instruments. As the field is young, new techniques and instruments are still being developed. This paper attempts to convey the scope of the field by:describing the capabilities of the respective research instruments for determining mineral characteristics, summarising investigations of gold as an example of applied mineralogy studies of precious metals, andpresenting a case history where applied mineralogists worked closely with mineral processing engineers on a base metal ore and mill products to help the engineers optimise their processes for maximum recoveries.

Jan 1, 2008

By Canterford J. H, Bologiannis F, Smith A. N

The Mutooroo copper mine is one of a number of deposits that have been evaluated by Adelaide and Wallaroo Fertilizers Ltd as a source of feed for the production of high- purity copper oxide at their Burra plant. For this deposit, the technique of solution mining or in-situ leaching appeared ideal. The Mutooroo production circuit and the results of the process optimization and environmental monitoring programmes are outlined. At the end of the experimental period described here, the production liquor typically contained I g/litre copper, yield- ing in excess of 5 t/month of cement product containing about 80 per cent copper. The environmental monitoring programme provided clear evidence that there had been no un- acceptable alteration to the properties of the groundwater in the country rock surround- ing the mineralized zone. It is anticipated that the experience gained at Mutooroo will be of considerable help in the development of other solution mining operations.

Jan 1, 1983

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005