Search Documents

By R Robinson

Modem occupational health practice can be described as the fitting of work to the individual and each individual to his job; perhaps a non-traditional way to view occupational health. This two-component description is achieved through the development of programs to implement and monitor specific job procedures, from the monitoring of unwanted exposures to contaminants to the auditing of mine sites. This paper is about such programs. Some attempt must be made to evaluate the effectiveness of the program and several performance indicators which are intended to measure the effectiveness of such a program are offered.

Jan 1, 1994

By F Hungerford, T Ren

"Gas management has always been a major concern for the ventilation officer of any gassy mine. With an increase of mining depth and gas content, there is a great demand for the development of in-seam drilling sites where boreholes can be drilled for the pre-drainage of gas prior to longwall operation. The ventilation and gas management in the drilling site therefore becomes a critical component of mine safety. In this study, advanced computational fluid dynamics technology was adopted to investigate the aerodynamics of gas emitting from the drilling site and boreholes during normal drilling and, in the case of a sudden gas inrush, from the borehole. In addition, the impact of different ventilation controls on gas removal in the drilling site was investigated. Modelling results indicate that gas accumulation zones could be formed if the ventilation system fails to deliver sufficient airflow to the drill site, especially when a sudden gas inrush from a borehole occurs. The configurations of brattice, layout of ventilation tubes and the gas emission rate all have a significant effect on the gas distribution. Due to variations in site-specific conditions, it would be desirable to conduct modelling studies to assess the effects and efficiencies of a ventilation design for the varying environment on-site before carrying out drilling practice. CITATION: Ren, T, Hungerford, F and Wang, Z, 2015. Computational modelling studies of ventilation management for underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference, pp 239–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By M Scoble, E Rubio

The re-engineering of manufacturing production systems has demonstrated the benefits from using production information for optimising processes. This paper explores the techniques and issues in the acquisition and analysis of mine production data for tactical decision making in production control. The use of information and operations management tools is presented in the context of block caving studies, with particular focus on the relationship between secondary breaking and LHD production performance.

Jan 1, 2000

By L Dubron

This study details a mineralogical and textural characterisation of West African iron ores with an emphasis on their behaviour during mineral processing. By means of both qualitative and quantitative characterisation, a simulation of the beneficiation process applied to these iron ores is performed. A series of different analytical tools are used, including:X-Ray Diffraction (XRD) for qualitative mineralogical analysis;• qualitative optical microscopy (phase identifi cation, description of micro-textures) and (semi)• quantitative optical microscopy (counting of particles, phases and textural types); and• chemical analysis.All the information provided by these analytical methods are combined into a quantitative mineralogical and textural analysis, here called ‘modal analysis’, which enables us to simulate the capability of West African iron ores to be benefi ciated by magnetic and gravimetric separation techniques.On one hand, both qualitative XRD and optical microscopy have revealed the presence of the following mineralogical phases: magnetite, haematite, goethite and quartz. On the other hand, the chemical analyses provide us with quantitative inputs expressed as oxides. We have converted the oxides into mineralogical contents expressed as magnetite, haematite, goethite and quartz. In this way, we build a simple quantitative mineralogical analysis.Beside this, the semi-quantitative approach of the characterisation by optical microscopy also provides us with a liberation study, enabling us to split the gangue-bearing content between two types of particles:1. liberated gangue-bearing particles, and2. composite particles composed by both iron (oxhydr) oxides and gangue-bearing minerals.We have assumed that we could anticipate the behaviour of these two kinds of particles through a mineral process, by simulating the removal of at least the liberated particles of gangue. Optical microscopy also revealed a trend in the weathering profi le of the Tokadeh ore horizon with a decrease from bottom to top of magnetite and an increase of both goethite and martite showing a higher level of oxidation and hydration in the upper ore horizon.We have applied this removal extent upon the quartz content of the mineralogical quantitative analysis and we have re-calculated the quantitative mineralogical analysis considering the expected decrease in the quartz content. Finally, by converting the re-calculated (oxhydr) oxides contents into iron grades and summing them, we do obtain a fi nal simulated iron grade for the upgraded products.

Jul 11, 2011

By D-J Min

Strategies and achievements in the Asian steel industry to construct industrial ecological chain are reviewed largely in the case of Japan, Korea and China. Emphasis is placed on the development of resource circulatory system for the minimisation of various wastes and emissions of green house gases (GHG), toxic gases and polluting particulates. The minimisation includes:Rationalisation of iron and steelmaking processes; Implementation of available relevant measures/technologies; Life cycle assessment in designing steel from semis to assembled products; Reduction, reuse and recycling of materials and energies; and Utilisation of core competence technologies to process domestic and industrial wastes. In view of global nature of the above wastes- and emission-issues, inter-industrial linkage and international cooperation across the borders in the Asian countries have become more important. Inter-industrial linkage definitely serves to cut back the wastes and emissions. Examples of such linkage and factors influencing the sustainability of the linkage are described with expectation for further development of the linkage. Importance of international cooperation cannot be overstressed under the circumstances where steel production in China exceeded 220 Mt and world production exceeded 945 Mt in 2003 and is still increasing. Practical measures are discussed to enhance the linkage and cooperation for effectively promoting the reduction, reuse and recycling, including implications for the nonferrous industry.

Jan 1, 2004

By R Strand, B Usher

Environmental compliance and mine designs are increasingly including assessment of flows and water qualities as a key driver to decision-making over life-of-mine. Integrated site-wide water quality models linked to dynamic water balances have been used for regulatory submissions, feasibility studies, operating mines and mine closure studies. These models, developed in GoldSim, link aqueous chemistry to the physical system of the site-wide water balance. Geochemical mechanisms included are determined from geochemical characterisation and site water monitoring, depending on the data availability at each site. External geochemical modelling using PHREEQC, version 2 (by D?L?Parkhurst and C?A?J?Appelo) and Geochemists Workbench (GWB), (by C?M?Bethke and The Board of Trustees of the University of Illinois) identifies the most important geochemical processes to be included in the model as a series of geochemical mechanisms which include source term loading rates, pH-buffering and equilibration of water quality. Water balance components include seasonal flow variability; waste facility water storage and system lags; run-off variability; milling processes and tailings production as a function of ore types; simulation of automated and scheduled maintenance of settling ponds; water re-routing for water treatment and freshwater demand, usage and storage.Case studies illustrating the use of these models for regulatory submissions and mine feasibility studies in a variety of climatic and regulatory environments show the utility and applicability of these models. Site-specific examples of these models developed by Klohn Crippen Berger Ltd are currently used at operating mines across the world. One of the larger mines where this is used is a mature poly-metallic mine in South America where the model has aided mine managers in understanding how various planned initiatives and potential water options will result in changes to flows and water quality. It is used regularly to inform water and waste management to minimise impacts to the receiving environment as a consideration of both flows and concentrations. The mine has also used the model in support of water treatment design, regulatory submissions and mine closure planning.Further examples of feasibility and operational/compliance assessment in arid and strongly seasonal environments for planning, regulatory and closure consideration of mine wastes and pits have shown the utility and usefulness of these approaches for a range of mining operations at various stages of mine life.CITATION:Strand, R and Usher, B, ?2014. Integrated site water balances and water quality models for decision-making over life-of-mine, in Proceedings Life-of-Mine 2014 , pp 271–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2006

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

By J Rowland

"Ventilation models are invaluable tools for both prediction of routine daily ventilation changesin an operating mine to circuit performance expectations at the mine in 20 yearsÆ time. Arguably ventilation offi cers are becoming increasingly reliant on maintaining an accurate ventilation model with which to do their work. This paper relates to the practical assessment of the accuracy and thus ability of a mine site ventilation model to be reliably utilised on such varied tasks. The author's experience shows that in some cases the incumbent model is found to be in a state of tune that demonstrates a mine wide detailed assessment of branch resistances is simply not required. The money spent on a detailed mine wide ventilation survey that is not required would be far bett er served purchasing much needed monitoring equipment, rather than fixing something that is possibly not even broken. The term ænot rocket scienceÆ has been incorporated into the title of this paper because it appears that many practitioners believe that circuit validation is diffi cult. As long as clear att ention to detail is paid to the actual data collection process then drawing an accuracy comparison between the circuit performance and the model performance at any particular point in time, is really very simple. This paper will show a manner in which a circuit can be analysed to determine its actual state of health by using various diagnostic tools and tips. It will help ensure that subsequent work scopes to address any highlighted model defi ciencies can be more effi ciently scoped and targeted. It will hopefully remind operational people that such self assessments can easily be done æin houseÆ if the appropriate steps are followed."

Jun 1, 2012

The new law on Environmental Protection and Management (Republic of Indonesia Law 32 of 2009) was passed by the Indonesian parliament in September 2009. This law aims to protect Indonesia's rapidly degrading environment by providing tougher provisions for both polluters and law enforcers. In doing so, the law introduces a number of new constraints and potential business risks that will affect all companies in Indonesia, particularly mining companies. Some of the newly introduced concepts follow.   Mining companies will now require an environmental license, issued by the Minister of Environment or local counterparts. This license is a prerequisite for all other business and operational permits. The Minister can revoke the environmental license at any time in case of an environmental incident or dispute. Mining companies may be exposed to additional environmental taxes and bonds besides already existing reclamation and mine closure bonds.   There is an increased risk of environmental lawsuits, due to more stringent controls on one side and greater protection for NGOs on the other side who make claims, false or true, against the company. Company executives and managers can be sued and they will be held accountable if environmental degradation has indeed occurred due to the company's activities.   Companies may face increased liabilities due to a change in the definition of contamination. The new definition is more stringent (and on occasion may prove too stringent to be practical); it also provides little room for flexibility in its application.   As implementing regulations are prepared over the coming two to three years, mining companies will need to adjust to the new law. A proactive approach is needed to minimise risk. Recommended actions include: upgrading existing environmental impact assessments to a higher standard; conducting baseline studies and thoroughly documenting environmental conditions on a regular basis; closely tracking regulatory changes, especially the forthcoming implementing regulations on the new environmental law; and regularly engaging key government and community stakeholders on environmental issues.

Jun 1, 2010

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By A Jyoti, J R. Black, R R. Haese, E O. Ansah

Copper (Cu) is a critical metal in the transition to a low-carbon power supply. Presently, low-grade copper sulfide ores account for almost 80 per cent of the global reserves. Large amounts of water are required to process these low-grade copper ores. The mining industry utilises lixiviants from recycled water from different sources to conserve water, whilst enhancing Cu recovery. Some utilise intermediate to pregnant leach solutions, sea water, and processed water from electrowinning circuits with highly variable concentrations of ions. Previous studies have highlighted the formation of precipitates that passivate the surfaces of minerals in these low-grade copper ores and/or block flow paths for lixiviant during heap leaching. In this study, we utilised concepts of phase replacement to devise an innovative means of controlling precipitation and increasing copper recovery using industrial brine as opposed to freshwater. We propose the formation of Al-rich phases (such as AlSO4 + or alunite) to replace iron sulfate and iron hydroxysulfates (such as jarosite) during the chalcopyrite dissolution-precipitation mechanism. The rationale is to have available Fe3+ throughout the chalcopyrite leaching process. We tested this method by carrying out various batch experiments using CaCl2, AlCl3, and NaCl industrial brine types compared to freshwater and explored the capacity to leach Cu from chalcopyrite. There is higher Cu recovery during oxidative leaching of chalcopyrite in industrial brine with 91 per cent recovery using AlCl3-rich brine, 84 per cent with NaCl-rich brine, and 56 per cent with CaCl2-rich brine as compared to 35 per cent recovery using freshwater. In the absence of Al3+, various forms of iron sulfates, and jarosite are formed, reducing the availability of Fe3+ for chalcopyrite dissolution. The introduction of Al3+ leads to the formation of AlSO4 + species, thus lowering sulfate activity and the tendency for K-jarosite formation.

Aug 24, 2022

By Ito H, Noguchi F, Ueda Y

DTA curves of synthesis lead sulfide and commercial. lead concentrates during oxidation were measured to clarify the mechanism of ox- idation of lead sulfide. The oxidation reac tions could be divided to elementary reactions with production of basic lead sulfates such as 2PbO PbSO4. An existance of iron sulfide played an important role of the oxidation of lead concentrates. The oxidation rates of lead sulfide were measured in the wide range of oxygen potenti- als using IR type SO2 gas-meter. The oxidation rates under low Po 2 which corresponds to the direct oxidation smelting were much lower than those obtained under high Pot. The combustion temperatures of lead sulfide were also measured by hot thermocouple method. Those values were extremly low compar- ing the oxidation temperatures obtained by DTA.

Jan 1, 1987

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J M. Galvin

The traditional engineering approach to assessing stability is based on comparing resisting force (capacity) to driving force (demand), or strength to working stress. In underground coal geomechanics, considerable effort has been expended on quantifying the strength of rock structures. However, this has not been matched by advances in determining the load acting on these structures, reflecting a reluctance by some to embrace numerical modelling to assess load magnitudes and distributions. Numerical modelling is a valuable aid as loading environments are a function of both the stiffness of the mine workings and the stiffness of the superincumbent strata and are statically indeterminate in most cases.This paper defines stiffness, which is often confused with elastic modulus. It shows that, effectively, stiffness encapsulates geology, depth of mining, panel width, pillar width and mining height. Therefore, these factors are variables that need to be taken into account when determining stress magnitudes and distributions about mine workings. A range of examples are presented that illustrate the significance of the stiffness of the superincumbent strata on surface subsidence; the magnitude and distribution of pillar and abutment load; and aspects of bord and pillar mining, pillar extraction and longwall mining. These examples provide bases for identifying the limitations of some empirical approaches to mine design, identifying how to compensate for some of these in design processes; and emphasising the need to make greater use of numerical modelling in understanding and quantifying loading environments in underground coal mining.CITATION:Galvin, J M, 2014. The significance of superincumbent strata stiffness and its impacts on coalmine design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014